Home › Vehicle Exterior › WIPER / WASHER › WASHER NOZZLE (for Hatchback Front Side)

WASHER NOZZLE (for Hatchback Front Side) > INSTALLATION



1. INSTALL WASHER NOZZLE SUB-ASSEMBLY
  1. Type A:

    1. Engage the 2 claws to install a new washer nozzle sub-assembly.



  1. Type B:



      E271797E06
    1. Align the rib of the washer hose with the rib of a new washer nozzle sub-assembly and connect them.
      Text in Illustration 
      *a
      Rib

      CAUTION:
      1. Make sure that the washer hose is not twisted when installing it in order to prevent interference with the hood and cowl top ventilator louver sub-assembly.
      2. It is possible to connect the hose even if it is twisted 360°, so check to make sure the hose is not twisted.

  1. Engage the 2 claws to install the washer nozzle sub-assembly.



2. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY


    E223416E02
  1. Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).
    Text in Illustration 
    *a
    Wire Brush
    *b
    Wiper Arm Serration
    *c
    Wiper Pivot Serration

  1. Clean the wiper arm serrations.

  1. Clean the wiper pivot serrations with a wire brush.



    E229454E01
  1. Install the front wiper sub arm.
    Text in Illustration 
    *a
    Pivot of Front Wiper Sub Arm

    NOTICE:
    1. When reusing the front wiper arm and blade assembly, apply MP grease to the pivot of the front wiper sub arm.
    2. Confirm that the front wiper sub arm is engaged to the pivot.



    E229455E04
  1. Install the front wiper arm and blade assembly with the nut to the position as shown in the illustration.
    Text in Illustration 
    *a
    Mark for Blade Position
    Installation Position 
    Mark
    Measurement
    a
    10 mm (0.394 in.)

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }

    HINT:
    1. There are 2 marks, so make sure to inspect using the correct mark.
    2. After tightening, confirm that the wiper blade is within the area shown in the illustration.



  1. Type A:



      E229003E02
    1. Align the rib of the washer hose with the rib of the washer nozzle sub-assembly and connect them.
      Text in Illustration 
      *a
      Rib

      NOTICE:
      1. Make sure that the washer hose is not twisted when installing it in order to prevent interference with the hood and cowl top ventilator louver sub-assembly.
      2. It is possible to connect the hose even if it is twisted 360°, so check to make sure the hose is not twisted.

      HINT:

      1. E229005E02
        If the washer hose has been disconnected at the joint side, align the rib of the washer hose with the rib of the washer hose joint and connect them.
        Text in Illustration 
        *a
        Rib

      2. E229006E02
        Check that the washer hose rib looks like the illustration.
        Text in Illustration 
        *1
        Washer Nozzle Sub-assembly
        *2
        Washer Hose Joint
        *3
        Washer Hose
        *a
        Rib



  1. Type B:



      E271684E04
    1. Align the rib of the washer hose with the rib of the washer hose joint and connect them.
      Text in Illustration 
      *a
      Rib

      NOTICE:
      1. Make sure that the washer hose is not twisted when installing it in order to prevent interference with the hood and cowl top ventilator louver sub-assembly.
      2. It is possible to connect the hose even if it is twisted 360°, so check to make sure the hose is not twisted.

      HINT:

      1. E271797E05
        If the washer hose has been disconnected at the washer nozzle sub-assembly side, align the rib of the washer hose with the rib of the washer nozzle sub-assembly and connect them.
        Text in Illustration 
        *a
        Rib

      2. E271795E04
        Check that the washer hose rib looks like the illustration.
        Text in Illustration 
        *1
        Washer Nozzle Sub-assembly
        *2
        Washer Hose Joint
        *3
        Washer Hose
        *a
        Rib

  1. Operate the front wipers while spraying washer fluid onto the windshield. Make sure that the front wipers function properly and the wipers do not come into contact with the vehicle body.



3. INSTALL FRONT WIPER ARM HEAD CAP


  1. Type A:



      E273234
    1. Engage the 3 claws to install the front wiper arm head cap.



  1. Type B:



    1. Engage the claw and rotate the front wiper arm head cap.


      E263513

    2. Engage the 3 claws to install the front wiper arm head cap.