ROOF HEADLINING (for Hatchback 5 Door) > REASSEMBLY |
| 1. INSTALL NO. 1 ROOF WIRE |
Align the No. 1 roof wire positioning tape with the markings of the roof headlining.

| *1 | Tape | *2 | Positioning Tape |
| *3 | Marking | - | - |
Install the No. 1 roof wire onto the roof headlining with 7 new pieces of tape.
| 2. INSTALL REAR SIDE RAIL SPACER RH (w/ Curtain Shield Airbag) |
![]() |
Align the markings on the roof headlining assembly with the rear side rail spacer and install the rail spacer using hot melt glue.
![]() | Adhesive Portion |
| 3. INSTALL REAR SIDE RAIL SPACER LH (w/ Curtain Shield Airbag) |
| 4. INSTALL REAR SIDE RAIL SPACER RH (w/o Curtain Shield Airbag) |
![]() |
Align the markings on the roof headlining assembly with the rear side rail spacer and install the rail spacer using hot melt glue.
![]() | Adhesive Portion |
| 5. INSTALL REAR SIDE RAIL SPACER LH (w/o Curtain Shield Airbag) |
| 6. INSTALL REAR ROOF SILENCER PAD |
![]() |
Align the markings on the roof headlining assembly with the 4 rear roof silencer pads and install the silencer pads using hot melt glue.
| 7. INSTALL NO. 2 ROOF PANEL PAD |
![]() |
Align the markings on the roof headlining assembly with the No. 2 roof panel pad and install the panel pad using hot melt glue.
| 8. INSTALL NO. 1 ROOF PANEL PAD |
![]() |
Align the markings on the roof headlining assembly with the No. 1 roof panel pad and install the panel pad using hot melt glue.
| 9. INSTALL NO. 5 ROOF SILENCER PAD |
![]() |
Align the markings on the roof headlining assembly with the 2 No. 5 roof silencer pads and install the silencer pads using hot melt glue.
| 10. INSTALL ROOF SILENCER PAD |
w/ Roof Panel Pad:
Align the markings on the roof headlining assembly with the roof silencer pad and install the silencer pads using hot melt glue.

| *1 | Roof Silencer Pad | *2 | Marking |
| *a | 25.0 mm (0.984 in.) | - | - |
w/o Roof Panel Pad:
Align the markings on the roof headlining assembly with the 4 roof silencer pads and install the silencer pads using hot melt glue.

| *1 | Roof Silencer Pad | *2 | Marking |
| *a | 25.0 mm (0.984 in.) | - | - |
| 11. INSTALL NO. 2 ROOF SILENCER PAD |
![]() |
Install a new No. 2 roof silencer pad as shown in the illustration.
| 12. INSTALL NO. 2 ANTENNA CORD SUB-ASSEMBLY |
Install the antenna cord into the clamp of the rear side rail spacer.

| *1 | Tape | *2 | Positioning Tape |
| *3 | Marking | - | - |
![]() | Front | - | - |
Align the 2 antenna cord positioning tapes with the markings of the roof headlining.
Install the antenna cord onto the roof headlining with 11 new pieces of tape.
Install the rest of antenna cord onto the roof headlining with a new piece of tape.

| *1 | Tape | *2 | Marking |
| *a | Rest of Antenna Cord | - | - |
![]() | Front | - | - |
| 13. INSTALL REAR SEAT SHOULDER BELT COVER |
![]() |
Engage the 6 claws and 2 guides and install the rear seat shoulder belt cover.