FRONT DOOR LOCK (for Hatchback) > INSTALLATION |
| 1. INSTALL FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY |
Install the front door inside locking cable to the front door lock.
| 2. INSTALL FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY |
Install the front door lock remote control cable to the front door lock.
![]() |
Engage the 7 claws.
| 3. INSTALL FRONT DOOR LOCK ASSEMBLY (w/ Power Door Lock) |
Apply MP grease to the sliding parts of the front door lock.
Install the door lock wire harness seal to the front door lock.
![]() |
Insert the front door lock open rod to the front door lock.
| *1 | Front Door Lock Open Rod |
![]() | Slide Direction |
Using a "TORX" socket wrench T30, install the front door lock with the 3 screws.
Connect the connector.
| 4. INSTALL FRONT DOOR LOCK ASSEMBLY (w/o Power Door Lock) |
Apply MP grease to the sliding parts of the front door lock.
Install the door lock wire harness seal to the front door lock.
![]() |
Insert the front door lock open rod to the front door lock.
| *1 | Front Door Lock Open Rod |
![]() | Slide Direction |
Using a "TORX" socket wrench T30, install the front door lock with the 3 screws.
| 5. INSTALL FRONT DOOR OUTSIDE HANDLE COVER |
Temporarily install the front door lock cylinder assembly.
Using a "TORX" socket wrench T30, install the front door lock cylinder assembly with the screw.
Install the hole plug.
| 6. INSTALL FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY |
![]() |
Engage the guide and install the front door rear lower frame sub-assembly.
Install the bolt.
| 7. INSTALL FRONT DOOR GLASS RUN |
![]() |
Install the front door glass run.
| 8. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY |
w/ Power Window:
Connect the power window regulator master switch assembly
Connect the cable to the negative (-) battery terminal.
Move the front door glass sub-assembly so that the door glass bolts can be seen.
Disconnect the cable from the negative (-) battery terminal.
Disconnect the power window regulator master switch assembly.
w/o Power Window:
Install the front door window regulator handle assembly.
Move the front door glass sub-assembly so that the door glass bolts can be seen.
Remove the front door window regulator handle assembly.
![]() |
Insert the front door glass sub-assembly into the front door panel along the front door glass run as indicated by the arrows in the order shown in the illustration.
![]() |
Install the front door glass sub-assembly with the 2 bolts.
![]() |
Install the front door service hole cover.
| 9. INSTALL FRONT DOOR SERVICE HOLE COVER (for 5 Door) |
Apply butyl tape to the front door panel.
Pass the front door lock remote control cable assembly, front door inside locking cable assembly and each connector through a new front door service hole cover.
![]() |
Install the new front door service hole cover according to the reference points on the front door panel.
| *a | Reference Point |
| 10. INSTALL FRONT DOOR SERVICE HOLE COVER (for 3 Door) |
Apply butyl tape to the front door panel.
Pass the front door lock remote control cable assembly, front door inside locking cable assembly and each connector through a new front door service hole cover.
![]() |
Install the new front door service hole cover according to the reference points on the front door panel.
| *a | Reference Point |
| 11. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY (for 5 Door) |
![]() |
Connect the front door lock remote control cable assembly and the front door inside locking cable assembly to the front door inside handle sub-assembly.
| *1 | Front Door Lock Remote Control Cable Assembly |
| *2 | Front Door Inside Locking Cable Assembly |
![]() |
Engage the 7 clips and install the front door trim board sub-assembly.
![]() |
Install the 3 screws.
![]() |
Engage the claw and close the cover.
| 12. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY (for 3 Door) |
![]() |
Connect the front door lock remote control cable assembly and the front door inside locking cable assembly to the front door inside handle sub-assembly.
| *1 | Front Door Lock Remote Control Cable Assembly |
| *2 | Front Door Inside Locking Cable Assembly |
![]() |
Engage the 8 clips and install the front door trim board sub-assembly.
![]() |
Install the 3 screws.
![]() |
Engage the claw and close the cover.
| 13. INSTALL FRONT ARMREST BASE UPPER PANEL (w/ Power Window) |
Connect the connector.
![]() |
Engage the 9 claws and 4 guides, and install the front armrest base upper panel.
| 14. INSTALL FRONT ARMREST BASE UPPER PANEL (w/o Power Window) |
Connect the connector.
![]() |
Engage the 6 claws and 3 guides, and install the front armrest base upper panel.
| 15. INSTALL FRONT DOOR WINDOW REGULATOR HANDLE ASSEMBLY (w/o Power Window) |
![]() |
Install the window regulator handle plate.
| *a | Inside of Vehicle |
Open all the windows.
![]() |
Install the front door window regulator handle assembly with the clip at the angle shown in the illustration.
| *a | Assemble with Glass in Fully Open Position |