Home › Vehicle Interior › DOOR LOCK › FRONT DOOR LOCK (for Hatchback)

FRONT DOOR LOCK (for Hatchback) > REMOVAL


HINT:
  1. Use the same procedure for both the RH and LH sides.
  2. The procedure described below is for the RH side.



1. REMOVE FRONT DOOR WINDOW REGULATOR HANDLE ASSEMBLY (w/o Power Window)


    B345202E03
  1. Insert a clip remover with its shaft wrapped in protective tape between the window regulator handle plate and front door trim board sub-assembly.
    Text in Illustration 
    *a
    Protective Tape

  1. Turn the front door window regulator handle assembly with the clip remover inserted, as shown in the illustration.

  1. Remove the front door window regulator handle assembly and the clip.

  1. Remove the window regulator handle plate.



2. REMOVE FRONT ARMREST BASE UPPER PANEL (w/ Power Window)


    B284582
  1. Using a moulding remover, disengage the 9 claws and the 4 guides.

  1. Disconnect the connector and remove the front armrest base upper panel.



3. REMOVE FRONT ARMREST BASE UPPER PANEL (w/o Power Window)


    B284583
  1. Using a moulding remover, disengage the 6 claws and the 3 guides.

    1. Disconnect the connector.

      HINT:
      If the armrest base upper panel is equipped with door lock switch, disconnect the connector.



4. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY (for 5 Door)


    B273456E02
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the claw and open the cover.
    Text in Illustration 
    *a
    Protective Tape



    B271595
  1. Remove the 3 screws.



    B271596
  1. Disengage the 7 clips.



    B271597E01
  1. Disconnect the front door lock remote control cable assembly and the front door inside locking cable assembly, and remove the front door trim board sub-assembly.
    Text in Illustration 
    *1
    Front Door Lock Remote Control Cable Assembly
    *2
    Front Door Inside Locking Cable Assembly



5. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY (for 3 Door)


    B273456E02
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the claw and open the cover.
    Text in Illustration 
    *a
    Protective Tape



    B271595
  1. Remove the 3 screws.



    B284585
  1. Disengage the 8 clips.



    B271597E01
  1. Disconnect the front door lock remote control cable assembly and the front door inside locking cable assembly, and remove the front door trim board sub-assembly.
    Text in Illustration 
    *1
    Front Door Lock Remote Control Cable Assembly
    *2
    Front Door Inside Locking Cable Assembly



6. REMOVE FRONT DOOR SERVICE HOLE COVER (for 5 Door)


    B271600
  1. Remove the front door service hole cover.

    HINT:
    Remove any butyl tape remaining on the door side.



7. REMOVE FRONT DOOR SERVICE HOLE COVER (for 3 Door)


    B284587
  1. Remove the front door service hole cover.

    HINT:
    Remove any butyl tape remaining on the door side.



8. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY


    B271601
  1. Remove the front door service hole cover.

  1. w/ Power Window:

    1. Connect the power window regulator master switch assembly.

    2. Connect the cable to the negative (-) battery terminal.

    3. Move the front door glass sub-assembly so that the door glass bolts can be seen.

    4. Disconnect the cable from the negative (-) battery terminal.

    5. Disconnect the power window regulator master switch assembly.

  1. w/o Power Window:

    1. Install the front door window regulator handle assembly.

    2. Move the front door glass sub-assembly so that the door glass bolts can be seen.

    3. Remove the front door window regulator handle assembly.



    B271602
  1. Remove the 2 bolts.



    B271603E01
  1. Remove the front door glass sub-assembly as indicated by the arrows in the order shown in the illustration.

    NOTICE:
    After the bolts are removed, do not allow the front door glass sub-assembly to fall.



9. REMOVE FRONT DOOR GLASS RUN


    B271607
  1. Remove the front door glass run.



10. REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY


    B271608
  1. Remove the bolt.

  1. Disengage the guide and remove the front door rear lower frame sub-assembly.



11. REMOVE FRONT DOOR OUTSIDE HANDLE COVER
  1. Remove the hole plug.



    B271615
  1. Using a "TORX" socket wrench T30, remove the screw and the front door lock cylinder assembly.



12. REMOVE FRONT DOOR LOCK ASSEMBLY (w/ Power Door Lock)


    B271626
  1. Disconnect the connector.

  1. Using a "TORX" socket wrench T30, remove the 3 screws.



    E221614E01
  1. Slide the front door lock assembly downward, and remove the front door lock from the front door lock open rod.
    Text in Illustration 
    *1
    Front Door Lock Open Rod
    V100135
    Slide Direction



    E221639
  1. Remove the door lock wire harness seal from the front door lock.



13. REMOVE FRONT DOOR LOCK ASSEMBLY (w/o Power Door Lock)


    E228974
  1. Using a "TORX" socket wrench T30, remove the 3 screws.



    E221614E01
  1. Slide the front door lock assembly downward, and remove the front door lock from the front door lock open rod.
    Text in Illustration 
    *1
    Front Door Lock Open Rod
    V100135
    Slide Direction



    E221639
  1. Remove the door lock wire harness seal from the front door lock.



14. REMOVE FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY


    B267270E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 7 claws.
    Text in Illustration 
    *1
    Protective Tape



    E221640
  1. Remove the front door lock remote control cable assembly from the front door lock.



15. REMOVE FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY


    E221641
  1. Remove the front door inside locking cable assembly from the front door lock.