Home › Vehicle Exterior › WIPER / WASHER › WIPER SWITCH (for Hatchback)

WIPER SWITCH (for Hatchback) > INSPECTION



1. INSPECT WINDSHIELD WIPER SWITCH ASSEMBLY


    E171721E59
  1. Check the front wiper switch.
    Text in Illustration 
    *a
    Component without harness connected
    (Windshield Wiper Switch Assembly)

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Front Wiper Switch 
      Tester Connection
      Switch Condition
      Specified Condition
      D108-1 (+S) - D108-3 (+1)
      OFF
      Below 1 Ω
      INT
      D108-2 (+B) - D108-3 (+1)
      MIST
      LO
      D108-2 (+B) - D108-4 (+2)
      HI

      If the result is not as specified, replace the wiper switch.



    E171721E60
  1. Check the front washer switch.
    Text in Illustration 
    *a
    Component without harness connected
    (Windshield Wiper Switch Assembly)

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Front Washer Switch 
      Tester Connection
      Switch Condition
      Specified Condition
      D107-2 (EW) - D107-3 (WF)
      ON
      Below 1 Ω
      OFF
      10 kΩ or higher

      If the result is not as specified, replace the wiper switch.



  1. Check the intermittent operation.


    E232203E02


    Text in Illustration 
    *A
    FAST: Connect battery negative lead to terminal D108-1 (+S)
    *B
    SLOW: Connect battery negative lead to terminal D108-1 (+S)
    *a
    Component without harness connected
    (Windshield Wiper Switch Assembly)
    *b
    Voltage between terminals D108-4 (+2) and D107-2 (EW)
    *c
    Wiper Switch
    *d
    Stop
    *e
    Start
    *f
    1.6 +/- 1 seconds
    *g
    10.7 +/- 5 seconds
    -
    -
    1. Connect the positive (+) lead to terminal D108-3 (+1) and the negative (-) lead to terminal D107-2 (EW).
    2. Connect the positive (+) lead to terminal D108-2 (+B) and the negative (-) lead to terminal D107-2 (EW) and D108-1 (+S).
    3. Turn the wiper switch to the INT position.
    4. Connect the positive (+) lead to terminal D108-1 (+S) for 5 seconds.
    5. Connect the negative (-) lead to terminal D108-1 (+S).
    6. Operate the intermittent wiper relay and check the voltage between terminals D108-3 (+1) and D107-2 (EW).

      OK:
      Voltage changes as shown in the illustration.

      If the result is not as specified, replace the wiper switch.



  1. Check the front washer operation.


    E232204E02


    Text in Illustration 
    *1
    Washer Switch
    -
    -
    *a
    Component without harness connected
    (Windshield Wiper Switch Assembly)
    *b
    Voltage between terminals D108-3 (+1) and D107-2 (EW)
    *c
    Approximately 0.5 seconds
    *d
    Approximately 2.2 seconds
    1. Connect the positive (+) lead to terminal D108-2 (+B) and the negative (-) lead to terminal D108-1 (+S) and D107-2 (EW).
    2. Connect the positive (+) lead to terminal D108-3 (+1) and the negative (-) lead to terminal D107-2 (EW).
    3. Turn the washer switch on and off, and check the voltage between terminals D108-3 (+1) and D107-2 (EW).

      OK:
      Voltage changes as shown in the illustration.

      If the result is not as specified, replace the wiper switch.



  1. Check the rear wiper switch (w/ Rear Wiper).



      E171721E61
    1. Measure the resistance according to the value(s) in the table below. (w/ Intermittent:)
      Text in Illustration 
      *a
      Component without harness connected
      (Windshield Wiper Switch Assembly)

      Standard Resistance:
      Rear Wiper Switch 
      Tester Connection
      Switch Condition
      Specified Condition
      D107-6 (C1R) - D107-2 (EW)
      OFF
      10 kΩ or higher
      D107-7 (+1R) - D107-2 (EW)
      D107-6 (C1R) - D107-2 (EW)
      INT
      Below 1 Ω
      D107-7 (+1R) - D107-2 (EW)
      HI
      Below 1 Ω

      If the result is not as specified, replace the wiper switch.



    2. E171721E62
    3. Measure the resistance according to the value(s) in the table below. (w/o Intermittent:)
      Text in Illustration 
      *a
      Component without harness connected
      (Windshield Wiper Switch Assembly)

      Standard Resistance:
      Rear Wiper Switch 
      Tester Connection
      Switch Condition
      Specified Condition
      D107-7 (+1R) - D107-2 (EW)
      OFF
      10 kΩ or higher
      D107-7 (+1R) - D107-2 (EW)
      ON
      Below 1 Ω

      If the result is not as specified, replace the wiper switch.



    E171721E63
  1. Check the rear washer switch (w/ Rear Wiper).
    Text in Illustration 
    *a
    Component without harness connected
    (Windshield Wiper Switch Assembly)

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Rear Washer Switch 
      Tester Connection
      Switch Condition
      Specified Condition
      D108-5 (WR) - D107-2 (EW)
      OFF
      10 kΩ or higher
      D107-7 (+1R) - D107-2 (EW)
      D108-5 (WR) - D107-2 (EW)
      WASH
      Below 1 Ω
      D108-5 (WR) - D107-2 (EW)
      ON + WASH
      Below 1 Ω
      D107-7 (+1R) - D107-2 (EW)

      If the result is not as specified, replace the wiper switch.