Home › Vehicle Exterior › BODY PANEL › FRONT BODY PILLAR
BM30M0E _01 Vehicle Exterior _068871 BODY PANEL _0336199 FRONT BODY PILLAR F

BODY PANEL  FRONT BODY PILLAR  CUT AND JOIN REPLACEMENT SECTIONS  


K108422

With the cowl top side upper panel removed.


REMOVAL


Symbol Meaning
K108818

Remove Weld Points
K108819

Remove Weld Points
K108820

Remove Weld Points
K108826

Cut with Disc Sander etc.
K108827

Cut and Join Location
K108828

Cut Location for Supply Parts


K141602C01
0.198,8.573 0.51,8.729 0.313,0.156 10 false *a 0.281,1.292 0.979,1.49 0.698,0.198 10 false 245 (9.65) 1.083,6.083 1.781,6.281 0.698,0.198 10 false 235 (9.25)
*a mm (in.) - -


K141603

INSTALLATION


Symbol Meaning
K108823

Plug Weld
K108824

Plug Weld
K108825

Plug Weld
K108827

Cut and Join Location
K108830

Fillet Weld
K108831

Butt Weld
K108834

Body Sealer


INSTALLATION POINT
1.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.

2.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)

3.

If the entire supply part is not needed, remove the part of the supply part that is needed.

4.

Before temporarily installing the new parts, weld the rocker reinforce sub-assembly outer, front pillar reinforcement sub-assembly lower and front body pillar sub-assembly inner with the standard number of welding points.

5.

When welding *a, make a hole on a new part for plug welding and weld the panel with the panel behind completely.

6.

Before installing a new part, apply body sealer.

HINT:

Apply body sealer in an even, continuous bead.


7.

After welding the rocker reinforce sub-assembly outer, front pillar reinforcement sub-assembly lower and front body pillar sub-assembly inner to the vehicle side, install the front body pillar outer and side panel to cowl gusset.

8.

After welding, apply the foamed sealing material to the corresponding parts. (See the painting/coating)

9.

After welding, apply body sealer to the corresponding parts. (See the painting/coating)

10.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.


K141604C01
0.708,1.792 0.51,1.792 0.51,1.792 0.823,1.115 false 2.031,1.958 1.781,1.958 1.781,1.958 2.063,2.521 false 5.042,3.208 5.219,3.208 5.219,3.208 5.625,2.969 false 0.74,1.719 1.052,1.875 0.313,0.156 10 false *1 2.083,1.906 2.396,2.063 0.313,0.156 10 false *2 4.885,3.125 5.198,3.281 0.313,0.156 10 false *3 0.167,8.542 0.479,8.698 0.313,0.156 10 false *b 1.448,0.24 2.115,0.427 0.667,0.188 10 false 235 (9.25) 4.417,2.26 5.083,2.448 0.667,0.188 10 false 160 (6.30) 1.458,4.604 2.031,4.802 0.573,0.198 10 false 10 (0.39) 6.271,7 6.844,7.198 0.573,0.198 10 false 15 (0.59)
*1 ROCKER REINFORCE SUB-ASSEMBLY OUTER *2 FRONT PILLAR REINFORCEMENT SUB-ASSEMBLY LOWER
*3 FRONT BODY PILLAR SUB-ASSEMBLY INNER - -
*b mm (in.) - -


K141605C01
0.177,8.531 0.49,8.688 0.313,0.156 10 false *b 1.115,8.094 1.75,8.292 0.635,0.198 10 false 15 (0.59) 1.698,8.354 2.333,8.552 0.635,0.198 10 false 10 (0.39) 2.313,8.094 2.948,8.292 0.635,0.198 10 false 15 (0.59)
*b mm (in.) - -


K141606C01
3.698,0.479 3.865,0.479 3.865,0.479 4.042,1.146 false 4.51,8.635 4.302,8.635 4.302,8.635 4.375,8.125 false 3.521,0.396 3.833,0.552 0.313,0.156 10 false *1 4.542,8.563 4.854,8.719 0.313,0.156 10 false *2 4.958,6.875 5.271,7.031 0.313,0.156 10 false *a 2.938,7.156 3.25,7.313 0.313,0.156 10 false *a 2.917,7.823 3.229,7.979 0.313,0.156 10 false *a
*1 FRONT BODY PILLAR OUTER *2 SIDE PANEL TO COWL GUSSET