Home › Vehicle Exterior › BODY PANEL › FIT STANDARD / ADJUSTMENT METHOD › 2013.08–2014.03
BM30M0E _01 Vehicle Exterior _068871 BODY PANEL _0336214 FIT STANDARD / ADJUSTMENT METHOD F

BODY PANEL  FIT STANDARD / ADJUSTMENT METHOD  ADJUSTMENT  


INSPECT HOOD SUB-ASSEMBLY


a.

Check that the clearance measurements are within the standard ranges.

B341584E01
0.24,3.771 0.458,4 0.219,0.229 10 false A 0.406,2.26 0.625,2.49 0.219,0.229 10 false B 1.469,0.729 1.688,0.958 0.219,0.229 10 false C 3.292,0.792 3.51,1.021 0.219,0.229 10 false D 4.625,0.438 4.844,0.667 0.219,0.229 10 false E 6.24,0.385 6.458,0.615 0.219,0.229 10 false F

Standard Clearance:
Area Measurement Area Measurement
A 4.0 to 8.0 mm (0.157 to 0.315 in.) B 4.0 to 8.0 mm (0.157 to 0.315 in.)
C 4.0 to 8.0 mm (0.157 to 0.315 in.) D 4.0 to 8.0 mm (0.157 to 0.315 in.)
E 3.4 to 6.4 mm (0.134 to 0.252 in.) F 2.5 to 5.5 mm (0.0984 to 0.217 in.)




HINT:

Centering bolts are used to mount the hood hinge and the hood lock. The hood and the hood lock cannot be adjusted with the centering bolts installed. Substitute the centering bolts with standard bolts when making adjustments.


ADJUST HOOD SUB-ASSEMBLY


a.

Adjust hood front/back position and left/right position of hood rear edge.

i.
B341587

Loosen the 4 hood side hinge bolts.


ii.

Move the hood to adjust the clearance to within the standard range.


iii.

Tighten the 4 hood side hinge bolts after the adjustment.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)



b.

Adjust up/down position of hood front left and front right corners.

i.
B341588

Turn the 2 cushion rubbers.

HINT:

The cushion rubber can be raised and lowered by turning it.




c.
B347095

Adjust up/down and left/right position of hood front edge.

i.

Loosen the 3 hood lock assembly bolts.


ii.

Adjust the hood lock position so that the striker can enter it smoothly.


iii.

Tighten the 3 hood lock assembly bolts after the adjustment.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)




INSPECT FRONT DOOR PANEL SUB-ASSEMBLY


a.

Check that the clearance measurements are within the standard ranges.

B356961C01
1.26,1.313 1.417,1.51 0.156,0.198 10 false A 1.302,1.833 1.458,2.031 0.156,0.198 10 false B 2.958,1.156 3.115,1.354 0.156,0.198 10 false C 2.927,1.813 3.083,2.01 0.156,0.198 10 false D 4.49,1.813 4.646,2.01 0.156,0.198 10 false F 4.375,1.208 4.531,1.406 0.156,0.198 10 false E 6.344,2.927 6.5,3.125 0.156,0.198 10 false G 6.375,4.521 6.531,4.719 0.156,0.198 10 false H 6.792,4.302 6.948,4.5 0.156,0.198 10 false I 4.854,5.688 5.01,5.885 0.156,0.198 10 false J 5.229,5.479 5.385,5.677 0.156,0.198 10 false K 3.792,5.5 3.948,5.698 0.156,0.198 10 false L 1.74,5.521 1.896,5.719 0.156,0.198 10 false M 1.24,5.302 1.396,5.5 0.156,0.198 10 false N 0.646,3.698 0.802,3.896 0.156,0.198 10 false O 0.135,3.49 0.292,3.688 0.156,0.198 10 false P

Standard Clearance:
Area Measurement Area Measurement
A 4.0 to 7.0 mm (0.157 to 0.276 in.) B 9.6 to 12.6 mm (0.378 to 0.496 in.)
C 4.0 to 7.0 mm (0.157 to 0.276 in.) D 5.1 to 8.1 mm (0.201 to 0.319 in.)
E 4.0 to 7.0 mm (0.157 to 0.276 in.) F 6.6 to 9.6 mm (0.260 to 0.378 in.)
G 4.4 mm (0.173 in.) H 3.2 to 5.6 mm (0.126 to 0.220 in.)
I -1.2 to 1.2 mm (-0.0472 to 0.0472 in.) J 3.2 to 5.6 mm (0.126 to 0.220 in.)
K -1.2 to 1.2 mm (-0.0472 to 0.0472 in.) L 4.5 to 7.5 mm (0.177 to 0.295 in.)
M 2.9 to 5.9 mm (0.114 to 0.232 in.) N -1.5 to 1.5 mm (-0.0591 to 0.0591 in.)
O 2.9 to 5.9 mm (0.114 to 0.232 in.) P -1.5 to 1.5 mm (-0.0591 to 0.0591 in.)




HINT:
·

Use the same procedure for the RH side and LH side.

·

The procedure listed below is for the LH side.

·

Centering bolts are used to mount the door hinge to the vehicle body and the door. The door cannot be adjusted with the centering bolts installed. Substitute the centering bolts with standard bolts when making adjustments.



ADJUST FRONT DOOR PANEL SUB-ASSEMBLY


HINT:

Use the same procedure for both sides.


a.
B346733

Using SST, adjust the door horizontally and vertically by loosening the 4 body side hinge bolts.

SST
09812-00010  


b.

Tighten the 4 body side hinge bolts after the adjustment.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


c.
B346734

Using SST, adjust the door horizontally and vertically by loosening the 4 door side hinge bolts.

SST
09812-00010  


d.

Tighten the 4 door side hinge bolts after the adjustment.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


e.
B346735

Using a T40 "TORX" socket wrench, slightly loosen the 2 striker mounting screws.


f.

Using a plastic-faced hammer, hit the striker to adjust its position.


g.

Using a T40 "TORX" socket wrench, tighten the 2 striker mounting screws after the adjustment.

Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)



INSPECT REAR DOOR PANEL SUB-ASSEMBLY


a.

Check that the clearance measurements are within the standard ranges.

B346772C01
2.458,0.531 2.615,0.729 0.156,0.198 10 false A 2.438,1.094 2.594,1.292 0.156,0.198 10 false B 3.917,0.427 4.073,0.625 0.156,0.198 10 false C 3.865,0.948 4.021,1.146 0.156,0.198 10 false D 6.813,3.302 6.969,3.5 0.156,0.198 10 false F 6.448,3.531 6.604,3.729 0.156,0.198 10 false E 4.844,5.104 5,5.302 0.156,0.198 10 false H 4.417,5.344 4.573,5.542 0.156,0.198 10 false G 3.24,5.042 3.396,5.24 0.156,0.198 10 false I 0.677,4.167 0.833,4.365 0.156,0.198 10 false J 1.156,3.896 1.313,4.094 0.156,0.198 10 false K 0.688,2.583 0.844,2.781 0.156,0.198 10 false L

Standard Clearance:
Area Measurement Area Measurement
A 4.0 to 7.0 mm (0.157 to 0.276 in.) B 6.3 to 9.3 mm (0.248 to 0.366 in.)
C 4.9 to 7.9 mm (0.193 to 0.311 in.) D 5.3 to 8.3 mm (0.209 to 0.327 in.)
E 2.9 to 5.9 mm (0.114 to 0.232 in.) F -1.5 to 1.5 mm (-0.0591 to 0.0591 in.)
G 2.9 to 5.9 mm (0.114 to 0.232 in.) H -1.5 to 1.5 mm (-0.0591 to 0.0591 in.)
I 4.5 to 7.5 mm (0.177 to 0.295 in.) J 3.2 to 5.6 mm (0.126 to 0.220 in.)
K -1.2 to 1.2 mm (-0.0472 to 0.0472 in.) L 4.4 mm (0.173 in.)




HINT:
·

Use the same procedure for the LH side and RH side.

·

The procedure listed below is for the LH side.

·

Centering bolts are used to mount the door hinge to the vehicle body and the door. The door cannot be adjusted with the centering bolts installed. Substitute the centering bolts with standard bolts when making adjustments.



ADJUST REAR DOOR PANEL SUB-ASSEMBLY


HINT:

Use the same procedure for both sides.


a.
B346773

Using SST, adjust the door horizontally and vertically by loosening the 4 body side hinge bolts.

SST
09812-00010  


b.

Tighten the 4 body side hinge bolts after the adjustment.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


c.
B346774

Using SST, adjust the door horizontally and vertically by loosening the 4 door side hinge bolts.

SST
09812-00010  


d.

Tighten the 4 door side hinge bolts after the adjustment.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


e.
B346775

Using a T40 "TORX" socket wrench, slightly loosen the 2 striker mounting screws.


f.

Using a plastic-faced hammer, hit the striker to adjust its position.


g.

Using a T40 "TORX" socket wrench, tighten the striker mounting 2 screws after the adjustment.

Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)



INSPECT LUGGAGE COMPARTMENT DOOR PANEL SUB-ASSEMBLY


a.

Check that the clearance measurements are within the standard ranges.

B343241E01
0.365,1.031 0.583,1.292 0.219,0.26 10 false A 1.688,1.052 1.906,1.313 0.219,0.26 10 false B 3.396,0.906 3.615,1.167 0.219,0.26 10 false C 5.146,1.375 5.365,1.635 0.219,0.26 10 false D 6.615,1.281 6.833,1.542 0.219,0.26 10 false E 6.479,3.635 6.698,3.896 0.219,0.26 10 false F

Standard Clearance:
Area Measurement Area Measurement
A 8.0 mm (0.315 in.) B 11.9 mm (0.469 in.)
C 2.8 to 5.8 mm (0.111 to 0.228 in.) D 6.4 to 10.4 mm (0.252 to 0.409 in.)
E 5.1 to 9.1 mm (0.201 to 0.358 in.) F 3.7 to 7.7 mm (0.146 to 0.303 in.)




HINT:

Centering bolts are used to mount the door hinge to the door. The door cannot be adjusted with the centering bolts installed. Substitute the centering bolts with standard bolts when making adjustments.


ADJUST LUGGAGE COMPARTMENT DOOR PANEL SUB-ASSEMBLY


a.
B343242

Adjust the door position.

i.

Horizontally and vertically adjust the door by loosening the 4 luggage compartment door side hinge bolts.


ii.

Tighten the 4 luggage compartment door side hinge bolts after the adjustment.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)



b.
B343243

Adjust the striker position.

i.

Using a T40 "TORX" socket wrench, slightly loosen the 2 striker mounting screws.


ii.

Using a plastic-faced hammer, hit the striker to adjust its position.


iii.

Using a T40 "TORX" socket wrench, tighten the 2 striker mounting screws after the adjustment.

Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)