Home › General › INTRODUCTION › WHEN REMOVING,INSTALLING OR REPLACING PARTS › 2014.03–2017.10
BM30M0E _V1 General _068870 INTRODUCTION _0336217 WHEN REMOVING,INSTALLING OR REPLACING PARTS F

INTRODUCTION  WHEN REMOVING,INSTALLING OR REPLACING PARTS  WHEEL ALIGNMENT STANDARD  


MEASURE VEHICLE HEIGHT (for Sedan)


NOTICE:
·

Before inspecting the wheel alignment, adjust the vehicle height to the specified value.

·

Be sure to perform measurement on a level surface.

·

If it is necessary to go under the vehicle for measurement, confirm that the parking brake is applied and the vehicle is secured with chocks.

·

Inspect while the vehicle is unloaded.

·

The standard value shown here is a value that is used for performing a wheel alignment and does not indicate the height of an actual vehicle.



a.

Bounce the vehicle up and down at the corners to stabilize the suspension.


b.
C282308E01
0.469,3.427 0.625,3.625 0.156,0.198 10 false A 2.875,3.385 3.052,3.604 0.177,0.219 10 false B 3.219,3.344 3.375,3.542 0.156,0.198 10 false D 0.156,3.313 0.313,3.51 0.156,0.198 10 false C

Measure the vehicle height.

Vehicle Height (Unloaded Vehicle):
except for Rough Road Package
Front C - A Rear D - B
87 mm (3.43 in.) 16 mm (0.630 in.)

for Rough Road Package
Front C - A Rear D - B
67 mm (2.64 in.) -4 mm (-0.157 in.)


Measurement Points:

A: Ground clearance of front lower No. 1 suspension arm bushing set bolt center


B: Ground clearance of rear trailing arm bushing set bolt center


C: Ground clearance of front wheel center


D: Ground clearance of rear wheel center




MEASURE VEHICLE HEIGHT (for Hatchback)


NOTICE:
·

Before inspecting the wheel alignment, adjust the vehicle height to the specified value.

·

Be sure to perform measurement on a level surface.

·

If it is necessary to go under the vehicle for measurement, confirm that the parking brake is applied and the vehicle is secured with chocks.

·

Inspect while the vehicle is unloaded.

·

The standard value shown here is a value that is used for performing a wheel alignment and does not indicate the height of an actual vehicle.



a.

Bounce the vehicle up and down at the corners to stabilize the suspension.


b.
C288201E01
0.51,3.49 0.667,3.688 0.156,0.198 10 false A 0.156,3.313 0.313,3.51 0.156,0.198 10 false C 2.885,3.396 3.042,3.594 0.156,0.198 10 false B 3.219,3.323 3.375,3.521 0.156,0.198 10 false D

Measure the vehicle height.

Vehicle Height (Unloaded Vehicle):
except for Rough Road Package
Front C - A Rear D - B
87 mm (3.43 in.) 16 mm (0.63 in.)

for Rough Road Package
Front C - A Rear D - B
67 mm (2.64 in.) -4 mm (-0.157 in.)


Measurement Points:

A: Ground clearance of front lower No. 1 suspension arm bushing set bolt center


B: Ground clearance of rear trailing arm bushing set bolt center


C: Ground clearance of front wheel center


D: Ground clearance of rear wheel center




INSPECT CAMBER, CASTER AND STEERING AXIS INCLINATION (FRONT WHEEL ALIGNMENT)


NOTICE:

Inspect while the vehicle is unloaded.


a.
C132440C15
0.99,1.479 0.667,1.073 false 2.708,0.75 2.302,1.083 false 2.76,0.667 2.99,0.844 0.229,0.177 10 false *b 0.49,0.969 0.729,1.146 0.24,0.177 10 false *a
*a Turning Radius Gauge
*b Camber-caster-kingpin Gauge


Put the front wheel on the center of the turning radius gauge.


b.

Remove the wheel cap or wheel hub ornament.


c.

Install the camber-caster-kingpin gauge at the center of the drive shaft.


d.

Inspect the camber, caster and steering axis inclination.

Camber (Unloaded Vehicle):
except for Rough Road Package
Tire Size Camber Inclination Right-left Difference
175/65R14 -0°08' +/- 0°45' (-0.13° +/- 0.75°) 0°45' (0.75°) or less
185/60R15 -0°09' +/- 0°45' (-0.15° +/- 0.75°)

for Rough Road Package
Tire Size Camber Inclination Right-left Difference
175/65R14 0°09' +/- 0°45' (0.15° +/- 0.75°) 0°45' (0.75°) or less
185/60R15 0°08' +/- 0°45' (0.13° +/- 0.75°)


Caster (Unloaded Vehicle):
except for Rough Road Package
Tire Size Caster Inclination Right-left Difference
175/65R14 4°41' +/- 0°45' (4.68° +/- 0.75°) 0°45' (0.75°) or less
185/60R15 4°42' +/- 0°45' (4.70° +/- 0.75°)

for Rough Road Package
Tire Size Caster Inclination Right-left Difference
175/65R14 4°24' +/- 0°45' (4.40° +/- 0.75°) 0°45' (0.75°) or less
185/60R15 4°25' +/- 0°45' (4.42° +/- 0.75°)


Steering Axis Inclination (Unloaded Vehicle):
except for Rough Road Package
Steering Axis Inclination (Reference)
11°03' (11.05°)

for Rough Road Package
Steering Axis Inclination (Reference)
10°32' (10.53°)


If the camber, caster and steering axis inclination are not within the specified range, inspect the suspension parts for damage and wear, and replace them if necessary.


e.

Remove the camber-caster-kingpin gauge.


f.

Install the wheel cap or wheel hub ornament.



INSPECT TOE-IN (FRONT WHEEL ALIGNMENT)


NOTICE:

Inspect while the vehicle is unloaded.


a.

Bounce the vehicle up and down at the corners to stabilize the suspension.


b.

Release the parking brake and move the shift lever to neutral.


c.

Push the vehicle straight ahead approximately 5 m (16.4 ft.). (Step A)


d.
C188968C19
2.521,1.333 2.521,1.667 false 0.823,0.552 0.844,1.094 0.844,1.094 1.333,0.594 true 0.76,1.135 0.938,1.302 0.177,0.167 10 false *a 2.427,1.698 2.604,1.854 0.177,0.156 10 false *b
*a Tread Center Mark
*b Dimension B
V100135

Front of the Vehicle


Put tread center marks on the rearmost points of the front wheels and measure the distance between the marks (dimension B).


e.

Slowly push the vehicle straight ahead to cause the front wheels to rotate 180°. Use the front tire valve as a reference point.

NOTICE:

Do not allow the wheels to rotate more than 180°. If the wheels rotate more than 180°, perform the procedure from (Step A) again.



f.
C188969C02
0.646,1.271 0.646,1.635 false 1.917,0.542 2.052,0.698 0.135,0.156 10 C 3.073,0.552 3.208,0.708 0.135,0.156 10 D 2.5,0.719 2.635,0.875 0.135,0.156 10 A 2.51,1.542 2.646,1.698 0.135,0.156 10 B 0.563,1.656 0.74,1.813 0.177,0.156 10 *a
*a Dimension A
V100135

Front of the Vehicle


Measure the distance between the tread center marks on the front of the wheels (dimension A).

Toe-in (Unloaded Vehicle):
except for Rough Road Package
Specified Condition
C + D: 0°09' +/- 0°12' (0.15° +/- 0.20°)
B - A: 1.4 +/- 2.0 mm (0.0551 +/- 0.0787 in.)

for Rough Road Package
Specified Condition
C + D: 0°07' +/- 0°12' (0.12° +/- 0.20°)
B - A: 1.1 +/- 2.0 mm (0.0433 +/- 0.0787 in.)


HINT:

Measure "B - A" only when "C + D" cannot be measured.


If the toe-in is not within the specified range, adjust it at the rack ends.



INSPECT WHEEL ANGLE (FRONT WHEEL ALIGNMENT)


NOTICE:

Inspect while the vehicle is unloaded.


a.
C132439C03
0.863,0.204 1.036,0.381 0.173,0.177 10 *b 0.538,0.204 0.713,0.381 0.176,0.177 10 *a 2.397,0.204 2.57,0.381 0.173,0.177 10 *b 2.725,0.204 2.901,0.381 0.176,0.177 10 *a
*a Inside
*b Outside
V100135

Front of the Vehicle


Put tread center marks on the rearmost points of a turning radius gauge.


b.

Turn the steering wheel fully to the left and right, and measure the turning angle.

Wheel Turning Angle (Unloaded Vehicle):
except for Rough Road Package
Tire Size Inside Wheel Outside Wheel
175/65R14 38°19' +/- 2°00' (38.32° +/- 2°) 33°16' (33.27°)
185/60R15 38°20' +/- 2°00' (38.33° +/- 2°)

for Rough Road Package
Tire Size Inside Wheel Outside Wheel
175/65R14 38°46' +/- 2°00' (38.77° +/- 2°) 33°36' (33.60°)
185/60R15 38°47' +/- 2°00' (38.78° +/- 2°)


If the right and left inside wheel angles differ from the specified range, check and adjust the right and left rack end lengths.



INSPECT CAMBER (REAR WHEEL ALIGNMENT)


NOTICE:

Inspect while the vehicle is unloaded.


a.

Remove the wheel cap or wheel hub ornament.


b.

Install the camber-caster-kingpin gauge and position the rear wheel on the turning radius gauge.


c.

Inspect the camber.

Camber (Unloaded Vehicle):
except for Rough Road Package
Camber Inclination Right-left Difference
-0°56' +/- 0°45' (-0.93° +/- 0.75°) 0°45' (0.75°) or less

for Rough Road Package
Camber Inclination Right-left Difference
-0°54' +/- 0°45' (-0.90° +/- 0.75°) 0°45' (0.75°) or less


If the camber is not within the specified range, inspect the suspension parts for damage and wear, and replace them if necessary.


d.

Remove the camber-caster-kingpin gauge.


e.

Install the wheel cap or wheel hub ornament.



INSPECT TOE-IN (REAR WHEEL ALIGNMENT)


NOTICE:

Inspect while the vehicle is unloaded.


a.

Bounce the vehicle up and down at the corners to stabilize the suspension.


b.

Release the parking brake and move the shift lever to neutral.


c.

Push the vehicle straight ahead approximately 5 m (16.4 ft.). (Step A)


d.
C188968C19
2.521,1.333 2.521,1.667 false 0.823,0.552 0.844,1.094 0.844,1.094 1.333,0.594 true 0.76,1.135 0.938,1.302 0.177,0.167 10 false *a 2.427,1.698 2.604,1.854 0.177,0.156 10 false *b
*a Tread Center Mark
*b Dimension B
V100135

Front of the Vehicle


Put tread center marks on the rearmost points of the rear wheels and measure the distance between the marks (dimension B).


e.

Slowly push the vehicle straight ahead to cause the rear wheels to rotate 180°. Use the rear tire valve as a reference point.

NOTICE:

Do not allow the wheels to rotate more than 180°. If the wheels rotate more than 180°, perform the procedure from (Step A) again.



f.
C188969C02
0.646,1.271 0.646,1.635 false 1.917,0.542 2.052,0.698 0.135,0.156 10 C 3.073,0.552 3.208,0.708 0.135,0.156 10 D 2.5,0.719 2.635,0.875 0.135,0.156 10 A 2.51,1.542 2.646,1.698 0.135,0.156 10 B 0.563,1.656 0.74,1.813 0.177,0.156 10 *a
*a Dimension A
V100135

Front of the Vehicle


Measure the distance between the tread center marks on the front of the rear wheels (dimension A).

Toe-in (Unloaded Vehicle):
except for Rough Road Package
Tire Size Specified Condition
175/65R14 C + D: 0°18' +/- 0°15' (0.30° +/- 0.25°)
B - A: 3.1 +/- 3.0 mm (0.122 +/- 0.118 in.)
185/60R15 C + D: 0°18' +/- 0°15' (0.30° +/- 0.25°)
B - A: 3.2 +/- 3.0 mm (0.126 +/- 0.118 in.)

for Rough Road Package
Tire Size Specified Condition
175/65R14 C + D: 0°14' +/- 0°15' (0.23° +/- 0.25°)
B - A: 2.5 +/- 3.0 mm (0.0984 +/- 0.118 in.)
185/60R15 C + D: 0°14' +/- 0°15' (0.23° +/- 0.25°)
B - A: 2.7 +/- 3.0 mm (0.106 +/- 0.118 in.)


HINT:

Measure "B - A" only when "C + D" cannot be measured.


If the toe-in is not within the specified range, inspect the suspension parts for damage and wear, and replace them if necessary.