Heat the double-sided tape remaining on the body with an infrared lamp or equivalent.
Heat the tape to 40 to 60°C for approximately 1 to 2 minutes.
Wipe off the remaining double-sided tape using a clean cloth or equivalent.
If a name plate is installed without thoroughly removing the remaining double-sided tape from the body, the name plate will not adhere properly. Make sure to thoroughly wipe off the double-sided tape.
After cleaning the installation area of the body with degreasing agent, attach the name plate to the position shown in the illustration.
The working environment should be 20°C when installing the name plate. If the working environment is below 20°C, heat the installation area of the body to 20 to 30°C and then install the name plate.
| *1 | NO. 1 BACK DOOR NAME PLATE | *2 | NO. 2 BACK DOOR NAME PLATE |
| *3 | NO. 3 BACK DOOR NAME PLATE | *4 | NO. 4 LUGGAGE COMPARTMENT DOOR PLATE |
| *5 | SYMBOL EMBLEM | - | - |
| ● | Non-reusable part | - | - |
NO. 3 BACK DOOR NAME PLATE
| *a | Radius End Point of Back Door | - | - |
| Mark | Measurement (along surface) | Mark | Measurement (along surface) |
| A | 49.2 mm (1.94 in.) | B | 94.0 mm (3.70 in.) |
| C | 97.6 mm (3.84 in.) | D | 159.4 mm (6.28 in.) |
NO. 4 LUGGAGE COMPARTMENT DOOR PLATE
for Type A:
| *a | Radius End Point of Back Door | - | - |
| Mark | Measurement (along surface) | Mark | Measurement (along surface) |
| A | 42.2 mm (1.66 in.) | B | 97.9 mm (3.85 in.) |
| C | 82.1 mm (3.23 in.) | D | 73.4 mm (2.89 in.) |
| E | 72.6 mm (2.86 in.) | F | 140.4 mm (5.53 in.) |
| G | 131.6 mm (5.18 in.) | - | - |
for Type B:
| *a | Radius End Point of Back Door | - | - |
| Mark | Measurement (along surface) | Mark | Measurement (along surface) |
| A | 42.6 mm (1.68 in.) | B | 98.7 mm (3.89 in.) |
| C | 82.2 mm (3.24 in.) | D | 73.3 mm (2.89 in.) |
| E | 73.0 mm (2.87 in.) | F | 140.4 mm (5.53 in.) |
| G | 131.8 mm (5.19 in.) | - | - |
for Type C:
| *a | Radius End Point of Back Door | - | - |
| Mark | Measurement (along surface) | Mark | Measurement (along surface) |
| A | 46.1 mm (1.81 in.) | B | 108.3 mm (4.26 in.) |
| C | 79.3 mm (3.12 in.) | D | 76.1 mm (3.00 in.) |
| E | 76.3 mm (3.00 in.) | F | 140.2 mm (5.52 in.) |
| G | 148.4 mm (5.84 in.) | - | - |
for Type D:
| *a | Radius End Point of Back Door | - | - |
| Mark | Measurement (along surface) | Mark | Measurement (along surface) |
| A | 126.9 mm (5.00 in.) | B | 51.1 mm (2.01 in.) |
| C | 114.4 mm (4.50 in.) | D | 93.8 mm (3.69 in.) |
| E | 126.9 mm (4.99 in.) | F | 51.2 mm (2.02 in.) |
| G | 114.2 mm (4.50 in.) | H | 93.9 mm (3.70 in.) |
NO. 2 BACK DOOR NAME PLATE
for Type A:
| *a | Radius End Point of Back Door | - | - |
| Mark | Measurement (along surface) | Mark | Measurement (along surface) |
| A | 139.9 mm (5.51 in.) | B | 231.1 mm (9.10 in.) |
| C | 74.4 mm (2.93 in.) | D | 35.2 mm (1.39 in.) |
for Type B:
| *a | Radius End Point of Back Door | - | - |
| Mark | Measurement (along surface) | Mark | Measurement (along surface) |
| A | 77.9 mm (3.07 in.) | B | 218.4 mm (8.60 in.) |
| C | 116.6 mm (4.59 in.) | D | 25.3 mm (1.00 in.) |
NO. 1 BACK DOOR NAME PLATE
| *a | Radius End Point of Back Door | - | - |
| Mark | Measurement (along surface) | Mark | Measurement (along surface) |
| A | 117.6 mm (4.63 in.) | B | 9.1 mm (0.358 in.) |
| C | 140.0 mm (5.51 in.) | D | 108.5 mm (4.27 in.) |
SYMBOL EMBLEM
| *a | Location Pin |