Home › Vehicle Exterior › BODY PANEL › FRONT DOOR OUTER PANEL › 2017.10–2018.01
BM30M0E _01 Vehicle Exterior _068871 BODY PANEL _0336201 FRONT DOOR OUTER PANEL F

BODY PANEL  FRONT DOOR OUTER PANEL  ASSEMBLY REPLACEMENT  


K111555

REMOVAL


Symbol Meaning
K108818

Remove Weld Points


REMOVAL POINT
1.

Before removing the outer panel, mark the installation position with tape.

2.

Before removing the outer panel, establish its exact position in relation to the window frame using a reference marker, etc.

3.

After grinding off the hemming location, remove the outer panel.


K111556C03
4.917,1.51 5.417,0.917 5.417,0.917 5.667,0.917 false 4,7.25 4.25,7.583 4.25,7.583 4.5,7.583 false 5.708,0.833 6.021,0.99 0.313,0.156 10 false *a 4.552,7.51 4.865,7.667 0.313,0.156 10 false *b 4.333,1.667 4.646,1.823 0.313,0.156 10 false *c 3.688,5.667 4,5.823 0.313,0.156 10 false *d 0.25,0.333 0.563,0.531 0.313,0.198 10 false *A
*A for TMMIN Made - -
*a Positioning Tape *b Disc Sander
*c Installation Position *d Hemming Location


K141952C03
4.865,1.74 5.167,1.333 5.167,1.333 5.333,1.333 false 3.979,7.125 4.333,7.5 4.333,7.5 4.5,7.5 false 5.406,1.26 5.719,1.417 0.313,0.156 10 false *a 4.583,7.417 4.896,7.573 0.313,0.156 10 false *b 4.292,1.896 4.604,2.052 0.313,0.156 10 false *c 3.646,5.479 3.958,5.635 0.313,0.156 10 false *d 0.25,0.333 0.563,0.531 0.313,0.198 10 false *A
*A for TMT Made - -
*a Positioning Tape *b Disc Sander
*c Installation Position *d Hemming Location


INSTALLATION


Symbol Meaning
K108823

Plug Weld
K108833

Spot MIG Weld
K108834

Body Sealer


INSTALLATION POINT
1.

Before temporarily installing the new parts, apply body sealer to the reinforcement, side impact protection beam and backside of the new parts.

NOTICE:

Do not close the drain hole.


HINT:

Apply sealer evenly about 10 mm (0.39 in.) from the flange and 3 mm (0.12 in.) in diameter on the outer panel and apply just enough sealer for the reinforcement and side impact protection beam to make contact.


2.

Bend the flange hem with a wooden hammer and dolly.

HINT:

Bend the panel gradually so as not to distort it.


3.

After welding, apply body sealer to the corresponding parts. (See the painting/coating)

4.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.


K111557C03
2.417,3.583 2.167,3.583 2.167,3.583 2.5,3.146 false 3.708,1.063 4,0.583 4,0.583 4.25,0.583 false 5.833,5.969 5.917,5.5 5.917,5.5 6.167,5.5 false 6.5,6.75 6.25,6.75 6.25,6.75 6.031,6.313 false 5.333,7.417 5.083,7.417 5.083,7.417 5.333,6.802 false 2.469,3.51 2.781,3.667 0.313,0.156 10 false *1 4.292,0.51 4.604,0.667 0.313,0.156 10 false *a 6.188,5.427 6.5,5.583 0.313,0.156 10 false *b 6.542,6.667 6.771,6.917 0.229,0.25 10 false *c 5.375,7.344 5.688,7.5 0.313,0.156 10 false *d 6.021,3.031 6.333,3.188 0.313,0.156 10 false *e 0.25,8.5 0.5,8.667 0.25,0.167 10 false *f 4.813,1.365 5.479,1.625 0.667,0.26 10 false 10 (0.39) 0.25,0.333 0.563,0.531 0.313,0.198 10 false *A
*A for TMMIN Made - -
*1 FRONT DOOR PANEL OUTER - -
*a Positioning Tape *b Cloth Tape
*c Dolly *d Wooden Hammer
*e Drain Hole *f mm (in.)


K141953C03
2.083,4 1.917,4 1.917,4 2.229,3.521 false 3.667,1.406 4,1.083 4,1.083 4.167,1.083 false 5.813,6.302 6,5.917 6,5.917 6.167,5.917 false 5.979,6.729 6.167,7.167 6.167,7.167 6.333,7.167 false 5.083,7.667 5.25,7.667 5.25,7.667 5.385,7.156 false 2.167,3.927 2.479,4.083 0.313,0.156 10 false *1 4.25,1 4.563,1.156 0.313,0.156 10 false *a 6.25,5.844 6.563,6 0.313,0.156 10 false *b 6.417,7.094 6.729,7.25 0.313,0.156 10 false *c 4.917,7.594 5.229,7.75 0.313,0.156 10 false *d 6.021,3.26 6.333,3.417 0.313,0.156 10 false *e 0.188,8.5 0.5,8.656 0.313,0.156 10 false *f 4.719,1.552 5.417,1.833 0.698,0.281 10 false 10 (0.39) 0.25,0.333 0.563,0.531 0.313,0.198 10 false *A
*A for TMT Made - -
*1 FRONT DOOR PANEL OUTER - -
*a Positioning Tape *b Cloth Tape
*c Dolly *d Wooden Hammer
*e Drain Hole *f mm (in.)