Home › Vehicle Exterior › BODY PANEL › CENTER BODY PILLAR › 2017.10–2018.01
BM30M0E _01 Vehicle Exterior _068871 BODY PANEL _0336200 CENTER BODY PILLAR F

BODY PANEL  CENTER BODY PILLAR  CUT AND JOIN REPLACEMENT SECTIONS  


K108400

REMOVAL


Symbol Meaning
K108818

Remove Weld Points
K108826

Cut with Disc Sander etc.
K108827

Cut and Join Location
K108828

Cut Location for Supply Parts


REMOVAL POINT
1.

*a is reused.


K141607C03
0.156,8.563 0.469,8.719 0.313,0.156 10 false *b 1.594,5.542 2.219,5.74 0.625,0.198 10 false 35 (1.38) 1.281,5.896 1.906,6.094 0.625,0.198 10 false 95 (3.74) 5.208,7.135 5.833,7.333 0.625,0.198 10 false 180 (7.09) 0.25,0.333 0.563,0.531 0.313,0.198 10 false *A
*A for TMMIN Made - -
*b mm (in.) - -


K141608C03
1.958,1.542 2.198,1.26 2.198,1.26 2.385,1.26 false 2.427,1.188 2.74,1.344 0.313,0.156 10 false *a 0.135,8.573 0.448,8.729 0.313,0.156 10 false *b 0.542,2.167 1.25,2.365 0.708,0.198 10 false 140 (5.51) 2.344,2.135 3.052,2.333 0.708,0.198 10 false 185 (7.28) 2.333,5.146 2.917,5.354 0.583,0.208 10 false 15 (0.59) 0.25,0.333 0.563,0.531 0.313,0.198 10 false *A
*A for TMMIN Made - -
*a Reused *b mm (in.)


K111413C05
0.25,8.51 0.563,8.667 0.313,0.156 10 false *b 1.667,5.625 2.313,5.854 0.646,0.229 10 false 35 (1.38) 1.281,5.979 1.927,6.208 0.646,0.229 10 false 95 (3.74) 5.25,7.104 6,7.333 0.75,0.229 10 false 180 (7.09) 0.167,0.177 0.479,0.333 0.313,0.156 10 false *A
*A for TMT Made - -
*b mm (in.) - -


K141947C04
2.115,1.604 2.333,1 2.333,1 2.5,1 false 0.333,2.177 1.083,2.427 0.75,0.25 10 false 140 (5.51) 2.427,2.167 3.177,2.417 0.75,0.25 10 false 185 (7.28) 2.281,5.146 3.031,5.396 0.75,0.25 10 false 10 (0.39) 2.521,0.917 2.833,1.115 0.313,0.198 10 false *a 0.25,8.469 0.563,8.667 0.313,0.198 10 false *b 0.188,0.167 0.5,0.365 0.313,0.198 10 false *A
*A for TMT Made - -
*a Reused *b mm (in.)


INSTALLATION


Symbol Meaning
K108823

Plug Weld
K108827

Cut and Join Location
K108830

Fillet Weld
K108831

Butt Weld


INSTALLATION POINT(for TMMIN Made)
1.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.

2.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)

3.

If the entire supply part is not needed, remove the part of the supply part that is needed.

4.

Before temporarily installing the new parts, weld the rocker reinforce sub-assembly outer, center body pillar reinforcement sub-assembly and No.1 inner pillar sub-assembly with the standard number of welding points.

5.

After welding the rocker reinforce sub-assembly outer, center body pillar reinforcement sub-assembly and No.1 inner pillar sub-assembly to the vehicle side, install the rear body front outside panel and *a.

6.

After welding, apply the foamed sealing material to the corresponding parts. (See the painting/coating)

7.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.


INSTALLATION POINT(for TMT Made)
1.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.

2.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)

3.

If the entire supply part is not needed, remove the part of the supply part that is needed.

4.

Carefully cut the No.1 inner pillar sub-assembly so not to damage *a.

5.

Before temporarily installing the new parts, weld the rocker reinforce sub-assembly outer, center body pillar reinforcement sub-assembly and No.1 inner pillar sub-assembly with the standard number of welding points.

6.

After welding the rocker reinforce sub-assembly outer, center body pillar reinforcement sub-assembly and No.1 inner pillar sub-assembly to the vehicle side, install the rear body front outside panel and *b.

7.

After welding, apply the foamed sealing material to the corresponding parts. (See the painting/coating)

8.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.


K141609C03
2.667,7.219 2.844,7.219 2.844,7.219 3.302,6.792 false 3.75,3.125 3.969,3.125 3.969,3.125 3.781,2.354 false 3.583,3.063 3.896,3.219 0.313,0.156 10 false *1 2.5,7.146 2.813,7.302 0.313,0.156 10 false *2 0.115,8.583 0.427,8.74 0.313,0.156 10 false *b 2.583,1.552 3.25,1.75 0.667,0.198 10 false 130 (5.12) 4.417,2.646 5.083,2.844 0.667,0.198 10 false 180 (7.09) 2.333,5.24 2.917,5.438 0.583,0.198 10 false 15 (0.59) 0.25,0.333 0.563,0.531 0.313,0.198 10 false *A
*A for TMMIN Made - -
*1 ROCKER REINFORCE SUB-ASSEMBLY OUTER *2 NO.1 INNER PILLAR SUB-ASSEMBLY
*b mm (in.) - -


K141610C03
5.5,4.844 5.792,4.292 5.792,4.292 5.573,4.292 false 5.396,4.219 5.625,4.375 0.229,0.156 10 false *1 0.25,0.333 0.563,0.531 0.313,0.198 10 false *A
*A for TMMIN Made - -
*1 CENTER BODY PILLAR REINFORCEMENT SUB-ASSEMBLY - -


K141611C03
0.146,8.552 0.458,8.708 0.313,0.156 10 false *b 3.354,8.448 3.927,8.646 0.573,0.198 10 false 10 (0.39) 0.25,0.333 0.563,0.531 0.313,0.198 10 false *A
*A for TMMIN Made - -
*b mm (in.) - -


K141612C03
3.781,6.438 4.115,5.854 4.115,5.854 4.271,5.854 false 3.958,1.146 3.885,0.323 3.885,0.323 4.083,0.323 false 4.115,0.25 4.427,0.406 0.313,0.156 10 false *1 4.313,5.792 4.625,5.948 0.313,0.156 10 false *a 0.25,0.333 0.563,0.531 0.313,0.198 10 false *A
*A for TMMIN Made - -
*1 REAR BODY FRONT OUTSIDE PANEL - -


K141948C04
3.667,3 3.5,3 3.5,3 3.75,2.333 false 3.302,6.833 2.917,7.333 2.917,7.333 2.75,7.333 false 3.333,5.396 2.948,5.896 2.948,5.896 2.781,5.896 false 3.74,2.927 4.052,3.083 0.313,0.156 10 false *1 2.521,7.25 2.833,7.406 0.313,0.156 10 false *2 0.167,8.51 0.479,8.667 0.313,0.156 10 false *c 2.604,1.531 3.552,1.76 0.948,0.229 10 false 130 (5.12) 4.438,2.667 5.385,2.896 0.948,0.229 10 false 180 (7.09) 2.313,5.208 3.26,5.438 0.948,0.229 10 false 10 (0.39) 2.604,5.813 2.917,5.969 0.313,0.156 10 false *a 0.25,0.333 0.563,0.531 0.313,0.198 10 false *A
*A for TMT Made - -
*1 ROCKER REINFORCE SUB-ASSEMBLY OUTER *2 NO.1 INNER PILLAR SUB-ASSEMBLY
*c mm (in.) - -


K141949C04
5.542,4.854 5.833,4.25 5.833,4.25 5.667,4.25 false 5.479,4.188 5.792,4.344 0.313,0.156 10 false *1 0.25,0.333 0.563,0.531 0.313,0.198 10 false *A
*A for TMT Made - -
*1 CENTER BODY PILLAR REINFORCEMENT SUB-ASSEMBLY - -


K141950C04
0.167,8.51 0.479,8.667 0.313,0.156 10 false *c 3.344,8.448 3.99,8.677 0.646,0.229 10 false 20 (0.79) 0.25,0.333 0.563,0.531 0.313,0.198 10 false *A
*A for TMT Made - -
*c mm (in.) - -


K141951C04
3.958,6.385 4.167,5.833 4.167,5.833 4.333,5.833 false 3.917,1.167 3.833,0.5 3.833,0.5 4,0.5 false 4.063,0.427 4.375,0.583 0.313,0.156 10 false *1 4.417,5.75 4.729,5.906 0.313,0.156 10 false *b 0.25,0.333 0.563,0.531 0.313,0.198 10 false *A
*A for TMT Made - -
*1 REAR BODY FRONT OUTSIDE PANEL - -