HANDLING OF A VEHICLE THAT HAS BEEN DAMAGED IN A COLLISION
Refer to the TOYOTA Repair Manual for the SRS airbag system inspection procedures.
If impacts are likely to occur to the front airbag sensor, No. 2 side airbag sensor assemblies, side airbag sensor assemblies or airbag ECU assembly remove each sensor as necessary beforehand.
Do not allow the front airbag sensor, No. 2 side airbag sensor assemblies, side airbag sensor assemblies or airbag ECU assembly to become heated to high temperatures.
Check the wire harnesses and connectors for damage and/or melting, as some areas of the airbags and seat belt pretensioners may heat up to several hundred degrees when they operate.
PRECAUTIONS FOR USING ELECTRIC WELDER
Check the Diagnostic Trouble Codes (DTCs).
If one or more DTCs are displayed:
Disconnect the negative (-) terminal cable from the battery.
Disconnect all the malfunctioning circuit connectors.
Disconnect the airbag ECU assembly connector.
If DTCs are NOT displayed:
Inspect for damage to the electric wiring harnesses and connectors.
Disconnect the negative (-) terminal cable from the battery.
Disconnect the airbag ECU assembly connector.
PARTS LOCATION
| *A | for TMMIN Made | - | - |
| *1 | FRONT AIRBAG SENSOR | *2 | FRONT SEAT OUTER BELT ASSEMBLY RH (FRONT PRETENSIONER SQUIB RH) |
| *3 | FRONT SEAT OUTER BELT ASSEMBLY LH (FRONT PRETENSIONER SQUIB LH) | - | - |
| *A | for TMT Made | *B | w/ Curtain Shield Airbag |
| *1 | FRONT AIRBAG SENSOR | *2 | NO. 2 SIDE AIRBAG SENSOR ASSEMBLY RH |
| *3 | NO. 2 SIDE AIRBAG SENSOR ASSEMBLY LH | *4 | SIDE AIRBAG SENSOR ASSEMBLY RH |
| *5 | SIDE AIRBAG SENSOR ASSEMBLY LH | - | - |
| *A | for TMT Made Sedan | *B | w/ Curtain Shield Airbag |
| *1 | CURTAIN SHIELD AIRBAG ASSEMBLY RH | *2 | CURTAIN SHIELD AIRBAG ASSEMBLY LH |
| *3 | FRONT SEAT OUTER BELT ASSEMBLY RH
(FRONT PRETENSIONER SQUIB RH) |
*4 | FRONT SEAT OUTER BELT ASSEMBLY LH
(FRONT PRETENSIONER SQUIB LH) |
| *A | for TMT Made Hatchback | *B | w/ Curtain Shield Airbag Assembly |
| *1 | CURTAIN SHIELD AIRBAG ASSEMBLY RH | *2 | CURTAIN SHIELD AIRBAG ASSEMBLY LH |
| *3 | FRONT SEAT OUTER BELT ASSEMBLY RH
(FRONT PRETENSIONER SQUIB RH) |
*4 | FRONT SEAT OUTER BELT ASSEMBLY LH
(FRONT PRETENSIONER SQUIB LH) |
| *A | for TMMIN Made | - | - |
| *1 | AIRBAG ECU ASSEMBLY | *2 | INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY (FRONT PASSENGER SIDE SQUIB) |
| *3 | SPIRAL CABLE SUB-ASSEMBLY | *4 | HORN BUTTON ASSEMBLY (DRIVER SIDE SQUIB) |
| *5 | COMBINATION METER ASSEMBLY | *6 | DRIVER SIDE JUNCTION BLOCK ASSEMBLY
- A/BAG-IG2 FUSE |
| *7 | DLC3 | - | - |
| *A | for TMT Made LHD | - | - |
| *1 | AIRBAG ECU ASSEMBLY | *2 | SPIRAL CABLE SUB-ASSEMBLY |
| *3 | DLC3 | *4 | DRIVER SIDE JUNCTION BLOCK ASSEMBLY |
| *5 | A/BAG-IG2 FUSE | - | - |
| *A | for TMT Made LHD | *B | w/ Curtain Shield Airbag |
| *1 | INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY | *2 | FRONT SEAT AIRBAG ASSEMBLY LH |
| *3 | FRONT SEAT AIRBAG ASSEMBLY RH | *4 | LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY |
| *5 | HORN BUTTON ASSEMBLY | - | - |
| *A | for TMT Made RHD | - | - |
| *1 | AIRBAG ECU ASSEMBLY | *2 | SPIRAL CABLE SUB-ASSEMBLY |
| *3 | DLC3 | *4 | DRIVER SIDE JUNCTION BLOCK ASSEMBLY |
| *5 | A/BAG-IG2 FUSE | - | - |
| *A | for TMT Made RHD | *B | w/ Curtain Shield Airbag |
| *1 | INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY | *2 | FRONT SEAT AIRBAG ASSEMBLY LH |
| *3 | FRONT SEAT AIRBAG ASSEMBLY RH | *4 | LOWER NO. 1 INSTRUMENT PANELAIRBAG ASSEMBLY |
| *5 | HORN BUTTON ASSEMBLY | - | - |