MEASURE VEHICLE HEIGHT (for Sedan)
Before inspecting the wheel alignment, adjust the vehicle height to the specified value.
Be sure to perform measurement on a level surface.
If it is necessary to go under the vehicle for measurement, confirm that the parking brake is applied and the vehicle is secured with chocks.
Inspect while the vehicle is unloaded.
The standard value shown here is a value that is used for performing a wheel alignment and does not indicate the height of an actual vehicle.
Bounce the vehicle up and down at the corners to stabilize the suspension.
Measure the vehicle height.
| Front C - A | Rear D - B |
|---|---|
| 87 mm (3.43 in.) | 16 mm (0.630 in.) |
| Front C - A | Rear D - B |
|---|---|
| 67 mm (2.64 in.) | -4 mm (-0.157 in.) |
A: Ground clearance of front lower No. 1 suspension arm bushing set bolt center
B: Ground clearance of rear trailing arm bushing set bolt center
C: Ground clearance of front wheel center
D: Ground clearance of rear wheel center
MEASURE VEHICLE HEIGHT (for Hatchback)
Before inspecting the wheel alignment, adjust the vehicle height to the specified value.
Be sure to perform measurement on a level surface.
If it is necessary to go under the vehicle for measurement, confirm that the parking brake is applied and the vehicle is secured with chocks.
Inspect while the vehicle is unloaded.
The standard value shown here is a value that is used for performing a wheel alignment and does not indicate the height of an actual vehicle.
Bounce the vehicle up and down at the corners to stabilize the suspension.
Measure the vehicle height.
| Front C - A | Rear D - B |
|---|---|
| 87 mm (3.43 in.) | 16 mm (0.63 in.) |
| Front C - A | Rear D - B |
|---|---|
| 67 mm (2.64 in.) | -4 mm (-0.157 in.) |
A: Ground clearance of front lower No. 1 suspension arm bushing set bolt center
B: Ground clearance of rear trailing arm bushing set bolt center
C: Ground clearance of front wheel center
D: Ground clearance of rear wheel center
INSPECT CAMBER, CASTER AND STEERING AXIS INCLINATION (FRONT WHEEL ALIGNMENT)
Inspect while the vehicle is unloaded.
| *a | Turning Radius Gauge |
| *b | Camber-caster-kingpin Gauge |
Put the front wheel on the center of the turning radius gauge.
Remove the wheel cap or wheel hub ornament.
Install the camber-caster-kingpin gauge at the center of the drive shaft.
Inspect the camber, caster and steering axis inclination.
| Tire Size | Camber Inclination | Right-left Difference |
|---|---|---|
| 175/65R14 | -0°08' +/- 0°45' (-0.13° +/- 0.75°) | 0°45' (0.75°) or less |
| 185/60R15 | -0°09' +/- 0°45' (-0.15° +/- 0.75°) | |
| 195/50R16 | -0°10' +/- 0°45' (-0.17° +/- 0.75°) |
| Tire Size | Camber Inclination | Right-left Difference |
|---|---|---|
| 175/65R14 | 0°09' +/- 0°45' (0.15° +/- 0.75°) | 0°45' (0.75°) or less |
| 185/60R15 | 0°08' +/- 0°45' (0.13° +/- 0.75°) |
| Tire Size | Caster Inclination | Right-left Difference |
|---|---|---|
| 175/65R14 | 4°41' +/- 0°45' (4.68° +/- 0.75°) | 0°45' (0.75°) or less |
| 185/60R15 | 4°42' +/- 0°45' (4.70° +/- 0.75°) | |
| 195/50R16 | 4°41' +/- 0°45' (4.68° +/- 0.75°) |
| Tire Size | Caster Inclination | Right-left Difference |
|---|---|---|
| 175/65R14 | 4°24' +/- 0°45' (4.40° +/- 0.75°) | 0°45' (0.75°) or less |
| 185/60R15 | 4°25' +/- 0°45' (4.42° +/- 0.75°) |
| Steering Axis Inclination (Reference) |
|---|
| 11°03' (11.05°) |
| Steering Axis Inclination (Reference) |
|---|
| 10°32' (10.53°) |
If the camber, caster and steering axis inclination are not within the specified range, inspect the suspension parts for damage and wear, and replace them if necessary.
Remove the camber-caster-kingpin gauge.
Install the wheel cap or wheel hub ornament.
INSPECT TOE-IN (FRONT WHEEL ALIGNMENT)
Inspect while the vehicle is unloaded.
Bounce the vehicle up and down at the corners to stabilize the suspension.
Release the parking brake and move the shift lever to neutral.
Push the vehicle straight ahead approximately 5 m (16.4 ft.). (Step A)
| *a | Tread Center Mark |
| *b | Dimension B |
|
Front of the Vehicle |
Put tread center marks on the rearmost points of the front wheels and measure the distance between the marks (dimension B).
Slowly push the vehicle straight ahead to cause the front wheels to rotate 180°. Use the front tire valve as a reference point.
Do not allow the wheels to rotate more than 180°. If the wheels rotate more than 180°, perform the procedure from (Step A) again.
| *a | Dimension A |
|
Front of the Vehicle |
Measure the distance between the tread center marks on the front of the wheels (dimension A).
| Tire Size | Specified Condition |
|---|---|
| 175/65R14
185/60R15 |
C + D: 0°09' +/- 0°12' (0.15° +/- 0.20°) |
| B - A: 1.4 +/- 2.0 mm (0.0551 +/- 0.0787 in.) | |
| 195/50R16 | C + D: 0°10' +/- 0°12' (0.16° +/- 0.20°) |
| B - A: 1.6 +/- 2.0 mm (0.0630 +/- 0.0787 in.) |
| Specified Condition |
|---|
| C + D: 0°07' +/- 0°12' (0.12° +/- 0.20°) |
| B - A: 1.1 +/- 2.0 mm (0.0433 +/- 0.0787 in.) |
Measure "B - A" only when "C + D" cannot be measured.
If the toe-in is not within the specified range, adjust it at the rack ends.
INSPECT WHEEL ANGLE (FRONT WHEEL ALIGNMENT)
Inspect while the vehicle is unloaded.
| *a | Inside |
| *b | Outside |
|
Front of the Vehicle |
Put tread center marks on the rearmost points of a turning radius gauge.
Turn the steering wheel fully to the left and right, and measure the turning angle.
| Tire Size | Inside Wheel | Outside Wheel |
|---|---|---|
| 175/65R14 | 38°19' +/- 2°00' (38.32° +/- 2°) | 33°16' (33.27°) |
| 185/60R15 | 38°20' +/- 2°00' (38.33° +/- 2°) | |
| 195/50R16 | 32°54' +/- 2°00' (32.90° +/- 2°) | 29°37' (29.62°) |
| Tire Size | Inside Wheel | Outside Wheel |
|---|---|---|
| 175/65R14 | 38°46' +/- 2°00' (38.77° +/- 2°) | 33°36' (33.60°) |
| 185/60R15 | 38°47' +/- 2°00' (38.78° +/- 2°) |
If the right and left inside wheel angles differ from the specified range, check and adjust the right and left rack end lengths.
INSPECT CAMBER (REAR WHEEL ALIGNMENT)
Inspect while the vehicle is unloaded.
Remove the wheel cap or wheel hub ornament.
Install the camber-caster-kingpin gauge and position the rear wheel on the turning radius gauge.
Inspect the camber.
| Camber Inclination | Right-left Difference |
|---|---|
| -0°56' +/- 0°45' (-0.93° +/- 0.75°) | 0°45' (0.75°) or less |
| Camber Inclination | Right-left Difference |
|---|---|
| -0°54' +/- 0°45' (-0.90° +/- 0.75°) | 0°45' (0.75°) or less |
If the camber is not within the specified range, inspect the suspension parts for damage and wear, and replace them if necessary.
Remove the camber-caster-kingpin gauge.
Install the wheel cap or wheel hub ornament.
INSPECT TOE-IN (REAR WHEEL ALIGNMENT)
Inspect while the vehicle is unloaded.
Bounce the vehicle up and down at the corners to stabilize the suspension.
Release the parking brake and move the shift lever to neutral.
Push the vehicle straight ahead approximately 5 m (16.4 ft.). (Step A)
| *a | Tread Center Mark |
| *b | Dimension B |
|
Front of the Vehicle |
Put tread center marks on the rearmost points of the rear wheels and measure the distance between the marks (dimension B).
Slowly push the vehicle straight ahead to cause the rear wheels to rotate 180°. Use the rear tire valve as a reference point.
Do not allow the wheels to rotate more than 180°. If the wheels rotate more than 180°, perform the procedure from (Step A) again.
| *a | Dimension A |
|
Front of the Vehicle |
Measure the distance between the tread center marks on the front of the rear wheels (dimension A).
| Tire Size | Specified Condition |
|---|---|
| 175/65R14 | C + D: 0°18' +/- 0°15' (0.30° +/- 0.25°) |
| B - A: 3.1 +/- 3.0 mm (0.122 +/- 0.118 in.) | |
| 185/60R15
195/50R16 |
C + D: 0°18' +/- 0°15' (0.30° +/- 0.25°) |
| B - A: 3.2 +/- 3.0 mm (0.126 +/- 0.118 in.) |
| Tire Size | Specified Condition |
|---|---|
| 175/65R14 | C + D: 0°14' +/- 0°15' (0.23° +/- 0.25°) |
| B - A: 2.5 +/- 3.0 mm (0.0984 +/- 0.118 in.) | |
| 185/60R15 | C + D: 0°14' +/- 0°15' (0.23° +/- 0.25°) |
| B - A: 2.7 +/- 3.0 mm (0.106 +/- 0.118 in.) |
Measure "B - A" only when "C + D" cannot be measured.
If the toe-in is not within the specified range, inspect the suspension parts for damage and wear, and replace them if necessary.