Heat the double-sided tape remaining on the body with an infrared lamp or equivalent.
Heat the tape to 40 to 60°C for approximately 1 to 2 minutes.
Wipe off the remaining double-sided tape using a clean cloth or equivalent.
If a name plate is installed without thoroughly removing the remaining double-sided tape from the body, the name plate will not adhere properly. Make sure to thoroughly wipe off the double-sided tape.
After cleaning the installation area of the body with degreasing agent, attach the name plate to the position shown in the illustration.
The working environment should be 20°C when installing the name plate. If the working environment is below 20°C, heat the installation area of the body to 20 to 30°C and then install the name plate.
| *A | for Type A | *B | for Type B |
| *C | for Type C | *D | w/ Brand Name Plate |
| *E | w/ Engine Displacement Mark | - | - |
| *1 | NO. 1 BACK DOOR NAME PLATE | *2 | NO. 2 BACK DOOR NAME PLATE |
| *3 | NO. 3 BACK DOOR NAME PLATE | *4 | NO. 4 LUGGAGE COMPARTMENT DOOR PLATE |
| *5 | SYMBOL EMBLEM | - | - |
| ● | Non-reusable part | - | - |
INSTALL NO. 1 BACK DOOR NAME PLATE (w/ Brand Name Plate)
| *1 | Back Door | - | - |
| Mark | Measurement (along surface) | Mark | Measurement (along surface) |
| A | 15.8 mm (0.622 in.) | B | 44.4 mm (1.748 in.) |
| C | 166.3 mm (6.548 in.) | D | 47.9 mm (1.886 in.) |
NO. 4 LUGGAGE COMPARTMENT DOOR PLATE
for Type A:
| *A | w/o Engine Displacement Mark | *B | w/ Engine Displacement Mark |
| *1 | Back Door | - | - |
| *a | R end | - | - |
| Mark | Measurement (along surface) | Mark | Measurement (along surface) |
| A | 46.7 mm (1.839 in.) | B | 56.5 mm (2.224 in.) |
| C | 61.9 mm (2.437 in.) | D | 100.9 mm (3.972 in.) |
| E | 43.7 mm (1.720 in.) | F | 14.7 mm (0.579 in.) |
| G | 57.5 mm (2.264 in.) | H | 59.4 mm (2.339 in.) |
for Type B:
| *A | w/o Engine Displacement Mark | *B | w/ Engine Displacement Mark |
| *1 | Back Door | - | - |
| *a | R end | - | - |
| Mark | Measurement (along surface) | Mark | Measurement (along surface) |
| A | 46.6 mm (1.835 in.) | B | 56.2 mm (2.213 in.) |
| C | 61.6 mm (2.425 in.) | D | 100.6 mm (3.960 in.) |
| E | 43.9 mm (1.728 in.) | F | 14.4 mm (0.567 in.) |
| G | 57.7 mm (2.272 in.) | H | 59.1 mm (2.327 in.) |
for Type C:
| *A | w/o Engine Displacement Mark | *B | w/o Engine Displacement Mark |
| *1 | Back Door | - | - |
| *a | R end | - | - |
| Mark | Measurement (along surface) | Mark | Measurement (along surface) |
| A | 41.5 mm (1.634 in.) | B | 55.9 mm (2.208 in.) |
| C | 62.6 mm (2.465 in.) | D | 96.1 mm (3.783 in.) |
| E | 40.9 mm (1.610 in.) | F | 29.0 mm (1.142 in.) |
| G | 54.3 mm (2.138 in.) | H | 57.4 mm (2.260 in.) |
INSTALL NO. 3 BACK DOOR NAME PLATE (w/ Engine Displacement Mark)
| *1 | Back Door | - | - |
| Mark | Measurement (along surface) | Mark | Measurement (along surface) |
| A | 47.7 mm (1.878 in.) | B | 67.0 mm (2.638 in.) |
| C | 61.6 mm (2.425 in.) | D | 121.6 mm (4.787 in.) |
NO. 2 BACK DOOR NAME PLATE
| *1 | Back Door | - | - |
| Mark | Measurement (along surface) | Mark | Measurement (along surface) |
| A | 23.9 mm (0.941 in.) | B | 153.9 mm (6.059 in.) |
| C | 13.8 mm (0.543 in.) | D | 8.2 mm (0.323 in.) |
SYMBOL EMBLEM
| *a | Location Pin |