Home › Engine / Hybrid System › 1NZ-FE ENGINE CONTROL › SFI SYSTEM › 2013.08–2016.10
NM30M0E _51 Engine / Hybrid System _018284 1NZ-FE ENGINE CONTROL _0090360 SFI SYSTEM DE DETAILS F

1NZ-FE ENGINE CONTROL  SFI SYSTEM  DETAILS  KNOCK CONTROL SENSOR  


CONSTRUCTION


a.

In a conventional knock control sensor (resonant type), a vibration plate is built into the sensor. This plate has the same resonance point as the knocking frequency of the engine block. This sensor can only detect vibration in this frequency band.


b.

A flat type knock control sensor (non-resonant type) has the ability to detect vibration in a wider frequency band (from about 5 kHz to 15 kHz). It has the following features.


c.

The engine knocking frequency will vary slightly depending on the engine speed. The flat type knock control sensor can detect vibration even when the engine knocking frequency changes. Due to the use of the flat type knock control sensor, the vibration detection ability is increased compared to a conventional type knock control sensor, and more precise ignition timing control is possible.

W111011E01
4,1.771 3.792,1.771 3.792,1.771 3.792,2.229 false 0.115,0.104 3.219,0.49 3.104,0.385 12 false Characteristics of Knock Control Sensor : 1.521,0.667 1.781,0.927 0.26,0.26 10 false (V) 1.177,1.594 1.771,1.885 0.594,0.292 10 false Voltage 3.948,1.073 6.24,1.365 2.292,0.292 10 false Detection Band of Resonant Type 4.083,1.688 5.802,2.01 1.719,0.323 10 false Detection Band of Flat Type 3.156,2.667 4.083,2.979 0.927,0.313 10 false Frequency 5.146,2.635 5.521,2.885 0.375,0.25 10 false (Hz) 0.906,3.104 4.771,3.385 3.865,0.281 10 false : Resonance Characteristic of Conventional Type (Resonant) 0.917,3.396 4.781,3.677 3.865,0.281 10 false : Resonance Characteristic of Flat Type (Non-resonant)


d.

A flat type knock control sensor is installed to an engine by placing it over the stud bolt installed on the cylinder block sub-assembly. For this reason, a hole for the stud bolt exists in the center of the sensor.


e.

In the sensor, a steel weight is located in the upper portion. An insulator is located between the weight and a piezoelectric element.


f.

An open/short circuit detection resistor is integrated in the sensor. When the ignition is ON, the open/short circuit detection resistor in the knock control sensor and the resistor in the ECM keep the voltage at terminal KNK1 constant. An Integrated Circuit (IC) in the ECM constantly monitors the voltage of terminal KNK1. If the open/short circuit occurs between the knock control sensor and the ECM, the voltage of terminal KNK1 will change and the ECM will detect the open/short circuit and store a Diagnostic Trouble Code (DTC).

W100954C08
1.083,1.958 0.958,1.24 0.958,1.24 0.865,1.24 true 1.146,1.875 0.958,0.615 0.958,0.615 0.865,0.615 true 1.167,1.75 1.313,0.531 1.313,0.531 1.417,0.531 true 2.313,1.948 2.396,0.76 2.396,0.76 2.51,0.76 true 5.698,1.542 6.115,0.802 6.115,0.802 6.219,0.802 true 5.76,1.573 6.104,1.958 6.104,1.958 6.188,1.958 true 0.677,1.167 0.875,1.354 0.198,0.188 10 false *3 0.677,0.542 0.875,0.729 0.198,0.188 10 false *2 1.469,0.479 1.667,0.667 0.198,0.188 10 false *1 2.563,0.677 2.76,0.865 0.198,0.188 10 false *4 6.229,0.75 6.427,0.938 0.198,0.188 10 false *3 6.198,1.885 6.396,2.073 0.198,0.188 10 false *5 1.479,2.344 1.792,2.542 0.313,0.198 10 false *a 5.438,2.49 5.75,2.688 0.313,0.198 10 false *b
*1 Steel Weight *2 Insulator
*3 Piezoelectric Element *4 Open/Short Circuit Detection Resistor
*5 Vibration Plate - -
*a Flat Type Knock Control Sensor (Non-resonant Type) *b Conventional Type Knock Control Sensor (Resonant Type)


W101046E01
0.719,0.438 3.323,0.76 2.604,0.323 10 Flat Type Knock Control Sensor 3.979,0.844 4.396,1.167 0.417,0.323 10 KNK1 3.938,1.49 4.396,1.813 0.458,0.323 10 EKNK 5.063,1.302 5.417,1.615 0.354,0.313 10 ECM 2.198,1.323 2.677,1.604 0.479,0.281 10 200kΩ 1.719,2.031 4.094,2.333 2.375,0.302 10 Open/Short Circuit Detection Resistor 0.76,2.344 2.208,2.573 1.448,0.229 10 Piezoelectric Element


g.

Vibrations caused by knocking are transmitted to the steel weight. The inertia of this weight applies pressure to the piezoelectric element. This action generates electromotive force.

W101072C07
3.573,1.281 2.896,1.146 2.896,1.146 2.708,1.146 true 3.583,0.948 2.917,0.271 2.917,0.271 2.719,0.271 true 2.552,1.042 2.75,1.271 0.198,0.229 10 false *2 2.531,0.208 2.729,0.438 0.198,0.229 10 false *1
*1 Steel Weight *2 Piezoelectric Element
V100135

Inertia - -