Home › Engine / Hybrid System › 2NZ-FE ENGINE MECHANICAL › ENGINE UNIT › 2013.08–2016.10
NM30M0E _51 Engine / Hybrid System _018294 2NZ-FE ENGINE MECHANICAL _0090363 ENGINE UNIT DE DETAILS F

2NZ-FE ENGINE MECHANICAL  ENGINE UNIT  DETAILS  CYLINDER BLOCK  


CONSTRUCTION


a.

Lightweight aluminum alloy is used for the cylinder block sub-assembly.


b.

The liners are the spiny-type, which have been manufactured so that their casting exterior forms a large irregular surface in order to enhance the adhesion between the liners and the aluminum cylinder block sub-assembly. The enhanced adhesion helps improve heat dissipation, resulting in a lower overall temperature and heat deformation of the cylinder bores.

W104602C01
4.615,1.802 4.719,1.802 4.719,1.802 5.083,2.125 true 6,2.427 5.896,2.427 5.896,2.427 5.604,2.135 true 5.781,1.354 5.99,1.104 5.99,1.104 6.094,1.104 true 4.302,0.698 4.594,0.948 0.292,0.25 10 false *a 4.417,1.719 4.677,1.938 0.26,0.219 10 false *1 6.146,1 6.396,1.208 0.25,0.208 10 false *2 6.042,2.375 6.302,2.594 0.26,0.219 10 false *3 2.406,0.958 2.573,1.146 0.167,0.188 10 true A 2.031,0.708 2.198,0.896 0.167,0.188 10 false A
*1 Irregularly Shaped Outer Casting Surface of Liner *2 Cylinder Block Sub-assembly
*3 Spiny Type Liner - -
*a A-A Cross Section - -



c.

Through the use of an offset crankshaft, the centerline of the cylinder bores is shifted 12 mm (0.472 in.) towards the intake in relation to the centerline of the crankshaft. Thus, the side force (thrust) applied to the cylinder walls is reduced when maximum combustion pressure is applied. This contributes to fuel economy.

W105059C01
4.292,2.344 3.802,1.5 3.802,1.5 3.688,1.5 true 5.75,2.344 5.25,1.656 5.25,1.656 5.135,1.656 true 1.469,1.031 1.719,1.323 0.25,0.292 10 false *a 1.948,0.594 2.198,0.885 0.25,0.292 10 false *b 3.521,1.406 3.771,1.698 0.25,0.292 10 false *c 1.865,3.167 2.115,3.458 0.25,0.292 10 false *c 4.344,3.167 4.594,3.458 0.25,0.292 10 false *e 5.781,3.208 6.031,3.5 0.25,0.292 10 false *f 4.344,0.313 4.594,0.604 0.25,0.292 10 false *d 5.656,0.313 5.906,0.604 0.25,0.292 10 false *d 4.958,1.563 5.208,1.854 0.25,0.292 10 false *c
*a 12 mm (0.472 in.) *b Cylinder Bore Centerline
*c Crankshaft Centerline *d Maximum Combustion Pressure
*e Offset Crankshaft *f Non-offset Crankshaft