Home › Drivetrain › U340E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM › 2013.08–2016.10
NM30M0E _52 Drivetrain _018302 U340E AUTOMATIC TRANSMISSION / TRANSAXLE _0090416 AUTOMATIC TRANSAXLE SYSTEM CO CONTROL F

U340E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  CONTROL  AUTOMATIC TRANSAXLE CONTROL  


FUNCTION OF MAIN COMPONENTS


a.

The main components of the U340E automatic transaxle system are as follows:

Component Function
Forward Clutch (C1) Connects the input shaft and front planetary sun gear.
Direct Clutch (C2) Connects the intermediate shaft and rear planetary carrier.
Reverse Clutch (C3) Connects the intermediate shaft and rear planetary sun gear.
OD and 2nd Brake (B1) Locks the rear planetary sun gear.
2nd Brake (B2) Prevents the rear planetary sun gear from turning counterclockwise.
1st and Reverse Brake (B3) Locks the front planetary ring gear and rear planetary carrier.
No. 1 1-way Clutch (F1) Prevents the rear planetary sun gear from turning counterclockwise.
No. 2 1-way Clutch (F2) Prevents the front planetary ring gear and rear planetary carrier from turning counterclockwise.
Planetary Gears Change the route through which driving force is transmitted, in accordance with the operation of both clutch and brake, in order to increase or reduce the input and output speed.
Shift Solenoid Valve S1
·

Switches the 2-3 shift valve.

·

Controls the C2 clutch.


Shift Solenoid Valve S2
·

Switches the 1-2 and 3-4 shift valves.

·

Controls the C1clutch and 2 brakes (B1 and B2).


Shift Solenoid Valve ST
·

Switches the 3-4 shift timing valve.

·

Switches the No. 1 4-3 shift timing valve.


Shift Solenoid Valve SL Controls the lock-up clutch.
Shift Solenoid Valve SLT
·

Controls the line pressure.

·

Controls the secondary pressure.

·

Controls the accumulator backpressure.


ATF Temperature Sensor (Transmission Wire) Detects the ATF temperature.
Speed Sensor NT (Transmission Revolution Sensor) Detects the input speed of the transaxle.
Park/Neutral Position Switch Assembly Detects the shift lever position.
Transmission Control Switch Detects the shift lever in 3 position.
Shift Lock Control ECU Sub-assembly Controls the shift lock system.
Stop Light Switch Assembly Detects the brake pedal depressed.
Combination Meter Assembly Detects the vehicle speed signal.
MIL Illuminates or blinks to inform the driver when the ECM detects a malfunction.
Shift Position Indicator Indicates the shift lever position.
ECM
·

Controls each shift solenoid valve and engine output in response to a signal from each sensor and switch.

·

When the ECM detects a malfunction, it makes a diagnosis and memorizes the failed section.





SYSTEM CONTROL


a.

Automatic Transaxle Controls List

Control Outline
Clutch to Clutch Pressure Control Controls the pressure that is applied directly to B1 brake and C1 clutch by actuating the shift solenoid valves (ST, SLT) in accordance with the ECM signals.
Clutch Pressure Control The shift solenoid valve SLT minutely controls the clutch pressure in accordance with the engine output and driving conditions.
Line Pressure Control Actuates the shift solenoid valve SLT to control the line pressure in accordance with information from the ECM and the operating conditions of the transaxle.
Shift Control in Uphill/Downhill Traveling Controls to restrict the 4th upshift or to provide appropriate engine braking by using the ECM to determine whether the vehicle is traveling on uphill or downhill.
Shift Timing Control The ECM sends current to the shift solenoid valve S1 and/or S2 based on signals from each sensor and shifts the gear.
Lock-up Timing Control The ECM sends current to the shift solenoid valve SL based on the signals from each sensor and engages or disengages the lock-up clutch.
Engine Torque Control Temporarily retards the engine ignition timing to restrict the output torque, thus ensuring the shift feel during up or down shifting.
"N" to "D" Squat Control When the shift lever is shifted from the "N" to "D" position, the gear is temporarily shifted to the 2nd and then to the 1st to reduce vehicle squat.
Shift Lock System The shift lock mechanism prevents the shift lever from being moved to any position other than P, unless the ignition switch is ON, and the brake pedal is depressed.
Fail-safe Even if a malfunction is detected in the sensors or solenoids, the ECM effects fail-safe control to prevent the vehicle's drivability from being affected significantly.
Diagnosis When the ECM detects a malfunction, the ECM makes a diagnosis and memorizes the failed section.


b.

Clutch to Clutch Pressure Control

i.

This control is used for shifting from 3rd to 4th gear, and from 4th to 3rd gear. It actuates shift solenoid valves ST and SLT in accordance with the signals from the ECM, and guides this output pressure directly to the No. 1 4-3 shift timing valve and the 3-4 shift timing valve in order to regulate the line pressure that acts on the B1 brake (OD and 2nd brake) and C1 clutch (forward clutch). As a result, smooth shift characteristics are delivered.


ii.

The B1 and C1 accumulators are made compact.

X106284E03
4.563,0.719 4.771,0.271 4.771,0.271 4.948,0.271 true 3.896,1.094 4.031,1.094 4.031,1.094 4.354,1.708 true 1.74,3.083 1.896,3.083 1.896,3.083 2.469,2.177 true 1.917,0.49 3.865,0.75 1.948,0.26 10 false Shift Solenoid Valve SLT 2.75,2.958 4.24,3.219 1.49,0.26 10 false Shift Solenoid Valve ST 4.99,0.188 6.719,0.583 1.729,0.396 10 false Accumulator Control Valve 2.563,1.042 3.906,1.302 1.344,0.26 10 false 3-4 Shift Timing Valve 0.979,2.5 1.979,2.771 1,0.271 10 false 3-4 Shift Valve 0.823,3.031 1.74,3.573 0.917,0.542 10 false No. 1 4-3 Shift Timing Valve 5.615,1.823 5.854,2 0.24,0.177 10 false C1 5.625,3.167 5.865,3.365 0.24,0.198 10 false B1



c.

Clutch Pressure Control

i.

The ECM monitors the signals from various types of sensor such as the speed sensor NT (transmission revolution sensor), allowing shift solenoid valve SLT to minutely control the clutch pressure in accordance with engine output and driving conditions. As a result, smooth shift characteristics have been realized.

X106285E03
2.885,3.958 2.427,2.656 2.427,2.656 2.292,2.656 true 3.854,4.25 3.917,4.531 3.917,4.531 4.01,4.531 false 0.281,0.896 0.698,1.563 0.417,0.667 10 false Input Shaft Speed 1.302,2.156 1.74,2.354 0.438,0.198 10 false Time 2.906,6.073 3.344,6.271 0.438,0.198 10 false Time 1.167,5.563 2.521,5.844 1.354,0.281 10 false Output Shaft Torque 5.25,4.708 6.792,4.927 1.542,0.219 10 false Solenoid Drive Signal 5.063,3.667 5.896,4.219 0.833,0.552 10 false Clutch/Brake Pressure 0.302,2.563 2.292,3.156 1.99,0.594 10 false Speed Sensor NT (Transmission Revolution Sensor) 4.135,1.208 4.51,1.417 0.375,0.208 10 false ECM 5.063,0.969 6.906,1.25 1.844,0.281 10 false Signal from Various Sensors 5.083,1.323 6.927,1.604 1.844,0.281 10 false Engine Speed 5.083,1.708 6.927,1.99 1.844,0.281 10 false Engine Torque Information 5.094,2.094 6.375,2.333 1.281,0.24 10 false ATF Temperature 4.063,4.458 4.927,5.063 0.865,0.604 10 false Shift Solenoid Valve SLT 1.708,0.688 2.552,1.115 0.844,0.427 10 false Target rpm Change Ratio 0.792,1.667 2.625,1.885 1.833,0.219 10 false Practical rpm Change Ratio



d.

Line Pressure Control

i.

Through the use of the shift solenoid valve SLT, the line pressure is appropriately controlled in accordance with the engine torque information, as well as with the internal operating conditions of the torque converter assembly and the transaxle.


ii.

Accordingly, the line pressure can be controlled minutely in accordance with the engine output, traveling condition and the ATF temperature, thus realizing smooth shift characteristics and regulating the workload in the oil pump.

X111701E01
0.5,0.146 2.49,0.344 1.99,0.198 10 false Line Pressure 1.75,0.958 2.948,1.26 1.198,0.302 10 false Primary Regulator 0.229,2.323 0.635,2.583 0.406,0.26 10 false Pump 1.448,3.365 2.396,3.646 0.948,0.281 10 false Fluid Pressure 2.333,4.219 2.906,4.521 0.573,0.302 10 false Current 3.302,3.063 4.531,3.583 1.229,0.521 10 false Shift Solenoid Valve SLT 3.885,0.302 5.219,0.927 1.333,0.625 10 false Shift Solenoid Valve Drive Signal 5.688,0.833 6.813,1.229 1.125,0.396 10 false Speed Sensor NT 5.698,1.323 6.823,1.719 1.125,0.396 10 false ATF Temperature 5.708,1.813 6.833,2.208 1.125,0.396 10 false Shift Position 5.708,2.292 6.563,2.833 0.854,0.542 10 false Throttle Valve Opening 5.688,3.042 7.073,3.448 1.385,0.406 10 false Intake Air Mass 5.698,3.51 7.083,3.917 1.385,0.406 10 false Engine Speed 5.698,4 6.656,4.604 0.958,0.604 10 false Engine Coolant Temperature



e.

Shift Control in Uphill/Downhill Traveling

i.

This control helps minimize the gear shifting when the driver operates the accelerator pedal while driving on a winding uphill or downhill road in order to ensure a smooth drive.


ii.

When the ECM detects uphill travel, it prohibits upshifting to 4th after downshifting to 3rd.


iii.

If a signal indicating that the driver has operated the brake pedal is input while the ECM detects downhill travel, it downshifts from 4th to 3rd.

X106323E02
5.094,0.563 6.167,0.917 1.073,0.354 10 false Brake Operation 0.469,2.792 1.469,3.125 1,0.333 10 false Without Control 0.667,3.167 1.458,3.5 0.792,0.333 10 false With Control 1.573,2.906 1.823,3.177 0.25,0.271 10 false 4th 1.927,2.927 2.177,3.198 0.25,0.271 10 false 3rd 1.573,3.281 1.823,3.552 0.25,0.271 10 false 4th 2.427,3.292 2.677,3.563 0.25,0.271 10 false 3rd 5.771,3.302 6.021,3.573 0.25,0.271 10 false 4th 4.719,3.292 4.969,3.563 0.25,0.271 10 false 3rd 2.354,2.927 2.604,3.198 0.25,0.271 10 false 4th 3.76,2.927 4.01,3.198 0.25,0.271 10 false 4th 3.75,3.292 4,3.563 0.25,0.271 10 false 4th 2.885,2.927 3.135,3.198 0.25,0.271 10 false 3rd


iv.

The actual acceleration calculated from the speed sensor signal is compared with the reference acceleration (based on level road travel) stored in the ECM to determine uphill or downhill travel.

X104263C02
2.792,0.479 2.906,0.229 2.906,0.229 3.063,0.229 true 3.083,0.146 3.292,0.354 0.208,0.208 10 false *a
*a Smaller - -
V100135

Reference Acceleration
V100136

Actual Acceleration


X104264C02
2.781,0.719 2.979,0.24 2.979,0.24 3.146,0.24 true 3.177,0.167 3.385,0.375 0.208,0.208 10 false *a
*a Greater - -
V100135

Reference Acceleration
V100136

Actual Acceleration





FAIL-SAFE


a.

The fail-safe function minimizes the loss of operability when an abnormality occurs in a sensor or shift solenoid valve.

Malfunction Part Function
Vehicle Speed Signal During a vehicle speed signal malfunction, the 4th upshift is prohibited.
Speed Sensor NT (Transmission Revolution Sensor) During a speed sensor NT (transmission revolution sensor) signal malfunction, the 4th upshift is prohibited.
ATF Temperature Sensor (Transmission Wire) During a ATF temperature sensor (transmission wire) malfunction, the 4th upshift is prohibited.
Shift Solenoid Valve SLT or ST During a shift solenoid valve SLT or ST malfunction, the 4th upshift is prohibited.
E.F.I. Engine Coolant Temperature Sensor, Knock Control Sensor or Throttle Position Sensor During an E.F.I. engine coolant temperature sensor, knock control sensor or throttle position sensor malfunction, the 4th upshift is prohibited.
Shift Solenoid Valve S1 or S2 During a malfunction in the shift solenoid valve S1 or S2, the current to the faulty shift solenoid valve is cut off and control is effected by operating the normal shift solenoid valves. Shift control is effected as described in the table below, depending on the failed shift solenoid valve.



DIAGNOSIS


a.

When the ECM detects a malfunction, the ECM records the malfunction and memorizes the information related to the fault. Furthermore, the ECM illuminates or blinks the MIL in the combination meter assembly to inform the driver.


b.

The ECM will also store the Diagnostic Trouble Codes (DTCs) of the malfunctions. The DTCs stored in the ECM are output to the Global TechStream (GTS) via the ECM and the DLC3.


c.

For details, refer to the Repair Manual.