Home › Suspension › REAR SUSPENSION › REAR SUSPENSION SYSTEM
NM30M0E _53 Suspension _018310 REAR SUSPENSION _0090426 REAR SUSPENSION SYSTEM GE GENERAL F

REAR SUSPENSION  REAR SUSPENSION SYSTEM  GENERAL  GENERAL  


OUTLINE


a.

A torsion-beam type suspension is used.


b.

Through the optimal specification of components, the rear suspension offers excellent riding comfort and stability.


c.

A rear axle carrier bush is obliquely mounted to obtain a toe-correct function, thus providing excellent driving stability and ride comfort.

X112486
1.188,4.313 1.427,4.313 1.427,4.313 1.552,3.885 true 2.813,4.917 3.052,4.917 3.052,4.917 3.25,4.406 true 4.75,5.615 4.479,5.615 4.479,5.615 4.344,5.104 true 4.594,4.49 4.458,3.938 4.458,3.938 4.198,3.938 true 5.24,3.625 5.49,3.323 5.49,3.323 5.708,3.323 true 5.167,3.125 4.865,2.635 4.865,2.635 4.635,2.635 true 4.5,2.573 4.813,2.771 0.313,0.198 10 false *1 5.792,3.281 6.104,3.479 0.313,0.198 10 false *3 4.052,3.865 4.365,4.063 0.313,0.198 10 false *2 4.813,5.552 5.125,5.75 0.313,0.198 10 false *5 2.667,4.844 2.979,5.042 0.313,0.198 10 false *4 1,4.229 1.313,4.427 0.313,0.198 10 false *6
*1 Rear Suspension Support *2 Rear Coil Spring
*3 Rear Shock Absorber Assembly *4 Axle Beam (Rear Axle Beam Assembly)
*5 Trailing Arm (Rear Axle Beam Assembly) *6 Rear Axle Carrier Bush




MAIN FEATURES


a.

Camber Change

i.

In a torsion-beam type suspension, the camber angle and the toe change differ between the bouncing case and the tramping case, offering both straight-line stability and excellent cornering stability.


ii.

The same as the full-trailing arm type suspension, the axis that joins the center of the right and left rear axle carrier bushings in the trailing arms (rear axle beam assembly) is the center of movement during any same direction travel.


iii.

Tramping Case: During tramping, or if a difference in suspension travel is created between the right and left wheels, the axle beam twists with its shearing center as the center of its rotation. Also, camber changes in relation to the suspension travel are determined by the ratio of the distance between the bushing in the trailing arm, the axle center and the shearing center ("α" in the figure below) and distance between the bushing in the trailing arm and the axle center ("L" in the figure below). Consequently, through the optimal allocation of the axle beam, the changes in the camber angle in relation to the suspension travel have been optimized, thus ensuring excellent cornering performance.

X105964
3.5,0.75 2.906,0.271 2.906,0.271 2.604,0.271 true 2.583,2.333 2.208,2.646 2.208,2.646 1.927,2.646 true 3.51,1.271 3.125,0.958 3.125,0.958 2.844,0.958 true 3.573,1.854 3.063,1.438 3.063,1.438 2.854,1.438 true 2.417,0.177 2.646,0.406 0.229,0.229 10 false *e 2.646,0.833 2.875,1.063 0.229,0.229 10 false *d 2.646,1.365 2.875,1.594 0.229,0.229 10 false *c 1.729,2.583 1.958,2.813 0.229,0.229 10 false *d 2.76,3.25 2.99,3.479 0.229,0.229 10 false *f 3.229,3.021 3.458,3.25 0.229,0.229 10 false L 4.604,2.719 4.833,2.948 0.229,0.229 10 false *b 5.354,1.188 5.583,1.417 0.229,0.229 10 false *a 2.813,2.74 3.042,2.969 0.229,0.229 10 false α
*a Bound *b Rebound
*c Shearing Center *d Center of Rear Axle Carrier Bushings
*e Instantaneous Rotational Axis of Right Axle *f Camber Change Rate α/L




b.

Anti-lift Geometry

i.

The lifting of the rear end of the vehicle during braking occurs due to the shifting of the center of gravity caused by inertia. The intersecting point (OR) supports the braking force (BF), and generates a force (BF1) in the direction of the intersecting point (OR) and a component force (BF2) in the direction of the ground contact. The force (BF1) can change the height of the intersecting point (OR). When the intersecting point (OR) is set high, it acts in the opposite direction (-▲W) of the load fluctuation (W) in order to restrain the lift.

X103912
1.99,2.292 2.354,2.594 0.365,0.302 10 OR 3.552,2.938 3.917,3.24 0.365,0.302 10 BF2 4.365,3.896 4.729,4.198 0.365,0.302 10 BF1 4.365,3.438 4.729,3.74 0.365,0.302 10 BF 3.552,3.51 3.917,3.813 0.365,0.302 10 W 3.365,4.052 3.729,4.354 0.365,0.302 10 -▲W



c.

Toe-correct Function

i.

The longitudinal and lateral forces that are created in the vehicle during cornering cause the rear axle carrier bushings in the trailing arms (rear axle beam assembly) to deform. On a right turn, the right trailing arm (rear axle beam assembly) moves forward and the left trailing arm (rear axle beam assembly) moves rearward, creating a tendency for the left wheel to toe-out. In this situation, the rear axle carrier bushings that are installed in the trailing arms (rear axle beam assembly) are designed to utilize the lateral force, which is applied to the bushings during cornering, to correct the left trailing arm (rear axle beam assembly) towards the toe-in direction.

X105966
1.458,1.885 0.927,2.313 0.927,2.313 0.677,2.313 true 1.51,3.365 0.969,3.813 0.969,3.813 0.719,3.813 true 2.594,3.5 2.833,3.625 2.833,3.625 2.521,3.625 true 5.833,3.563 6.052,3.865 6.052,3.865 5.74,3.615 true 0.427,2.25 0.833,2.542 0.406,0.292 10 false *1 0.5,3.719 0.906,4.01 0.406,0.292 10 false *1 2.875,3.563 3.281,3.854 0.406,0.292 10 false *2 6.115,3.844 6.521,4.24 0.406,0.396 10 false *2 0.302,0.521 0.708,0.813 0.406,0.292 12 false *A : 3.802,0.542 4.208,0.833 0.406,0.292 12 false *B :
*A Without Toe-correct Function *B With Toe-correct Function
*1 Rear Axle Carrier Bushings *2 Left Wheel
V100135

Bushing Movement
V100136

Lengthwise Force
V100137

Lateral Force
V100138

Lateral Force Applied to the Bushing





PRECAUTION


a.

Be sure to use the jack-up points that are provided on the body when raising the vehicle on the jack. Never apply a jack under the component parts of the rear suspension.