Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM
NM30M0E _55 Steering _018317 POWER ASSIST SYSTEMS _0090433 POWER STEERING SYSTEM DE DETAILS F

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  DETAILS  TORQUE SENSOR  


CONSTRUCTION


a.

The torque sensor with Hall ICs is used.


b.

The torque sensor is built into the steering column. A multipole magnet is mounted to the input shaft, and a yoke is mounted to the output shaft. The input and output shafts are joined by the torsion bar.


c.

The magnetic convergence ring assembly contains Hall ICs, which face opposite to each other. The system detects the steering direction in accordance with the direction of the magnetic flux that the amount of change in the magnetic flux density based on the relative displacement of the multipole magnet and the yoke. The power steering ECU assembly monitors the torque sensor signals that are output by the two Hall ICs to detect malfunctions.

X106003
1.688,3.167 2.094,3.75 2.094,3.75 2.323,3.75 true 1.531,3.938 1.125,4.51 1.125,4.51 0.896,4.51 true 4.667,2.135 4.042,2.958 4.042,2.958 3.823,2.958 true 1.823,1.292 2.302,0.458 2.302,0.458 2.531,0.458 true 4.854,1.292 5.49,0.719 5.49,0.719 5.708,0.719 true 5.771,2.01 6.031,1.5 6.031,1.5 6.25,1.5 true 4.76,1.667 4.135,1.083 4.135,1.083 3.906,1.083 true 5.167,1.677 4.135,1.073 true 5.365,2.135 4.063,2.948 true 2.344,3.677 2.615,3.927 0.271,0.25 10 false *3 2.573,0.385 2.844,0.635 0.271,0.25 10 false *1 0.708,4.448 0.979,4.698 0.271,0.25 10 false *2 3.656,2.875 3.927,3.125 0.271,0.25 10 false *6 5.74,0.625 6.01,0.875 0.271,0.25 10 false *3 3.74,1.01 4.01,1.26 0.271,0.25 10 false *4 6.281,1.406 6.552,1.656 0.271,0.25 10 false *5
*1 Input Shaft *2 Output Shaft
*3 Torsion Bar *4 Multipole Magnet
*5 Hall IC *6 Yoke


X106004
4.865,1.302 6.146,2.083 1.281,0.781 10 false Power Steering ECU Assembly 1.51,0.375 2.635,0.625 1.125,0.25 10 false Torque Sensor 4.146,0.76 4.604,1.01 0.458,0.25 10 false TRQV 4.146,1.167 4.594,1.458 0.448,0.292 10 false TRQ1 4.125,1.573 4.594,1.854 0.469,0.281 10 false TRQG 4.156,2.198 4.594,2.448 0.438,0.25 10 false TRQ2 1.208,0.948 1.792,1.24 0.583,0.292 10 false Hall IC 1 1.219,1.99 1.927,2.25 0.708,0.26 10 false Hall IC 2

NOTICE:

After replacing the steering column assembly, the steering gear assembly or the power steering ECU assembly, calibration of the torque sensor zero point is required. For details, refer to the Repair Manual.




OPERATION


a.

Straightline Driving

i.

If the vehicle is driven straight and the driver does not turn the steering wheel, the yoke is located in the center between the N and S poles of the multipole magnet. Thus, no magnetic flux passes between the Hall ICs. In this case, the Hall ICs output a specified voltage to the power steering ECU assembly, to indicate that the steering wheel is in the neutral position. Therefore, it does not apply current to the power steering motor.

X106006
2.281,1.229 1.948,0.552 1.948,0.552 1.729,0.552 true 4.865,1.698 5.094,1.25 5.094,1.25 5.313,1.25 true 4.896,1.99 5.115,2.448 5.115,2.448 5.333,2.448 true 1.948,2.063 1.563,2.677 1.563,2.677 1.333,2.677 true 1.135,2.594 1.406,2.844 0.271,0.25 10 false *2 5.333,1.167 5.604,1.417 0.271,0.25 10 false *3 5.385,2.365 5.656,2.615 0.271,0.25 10 false *4 1.542,0.469 1.813,0.719 0.271,0.25 10 false *1 2,1.646 2.271,1.896 0.271,0.25 10 false N 2.917,1.646 3.188,1.896 0.271,0.25 10 false N 3.802,1.646 4.073,1.896 0.271,0.25 10 false N 2.458,1.646 2.729,1.896 0.271,0.25 10 false S 3.365,1.646 3.635,1.896 0.271,0.25 10 false S
*1 Yoke *2 Multipole Magnet
*3 Hall IC 1 *4 Hall IC 2




b.

When Steering

i.

When a driver turns the steering wheel to the right or left, the twist that is created in the torsion bar creates a relative displacement between the multipole magnet and yoke.


ii.

At this time, the magnetic flux from the N to S pole of the multipole magnet passes between the Hall ICs. The system detects the steered direction of the steering wheel in accordance with the direction opposite to each other. As a result, the output characteristics of the 2 Hall ICs are constantly opposite each other. The system monitors the different outputs of these Hall ICs in order to detect malfunction.


iii.

The magnetic flux density becomes higher as it gets closer to the center of the respective pole. A Hall IC converts these magnetic flux fluctuations into voltage fluctuations, in order to transmit the turning torque of the steering wheel to the power steering ECU assembly.


iv.

The magnetic flux density becomes higher as it gets closer to the center of the respective pole. A Hall IC converts these magnetic flux fluctuations into voltage fluctuations, in order to transmit the turning torque of the steering wheel to the power steering ECU assembly.

X106007
2.844,1.76 3.167,0.76 3.167,0.76 3.385,0.76 true 3.792,4.75 4.104,3.75 4.104,3.75 4.333,3.75 true 6.448,1.74 6.74,0.729 6.74,0.729 6.51,0.729 true 6.458,2.01 6.75,3.021 6.75,3.021 6.521,3.021 true 2.854,2 3.177,3 3.177,3 3.396,3 true 0.292,1.698 0.563,1.948 0.271,0.25 10 false N 1.094,2.729 2.042,2.979 0.948,0.25 10 false Right Turn 5.271,6.313 6.219,6.563 0.948,0.25 10 false Right Turn 0.958,4.698 1.906,4.948 0.948,0.25 10 false Voltage 4.396,3.688 6.344,3.938 1.948,0.25 10 false Neutral Position 3.115,5.979 5.063,6.229 1.948,0.25 10 false Twist Angle of Torsion Bar 4.74,2.708 5.688,2.958 0.948,0.25 10 false Left Turn 1.573,6.323 2.521,6.573 0.948,0.25 10 false Left Turn 3.417,0.688 4.344,0.938 0.927,0.25 10 false Hall IC 1 5.896,0.656 6.823,0.906 0.927,0.25 10 false Hall IC 1 3.417,2.917 4.344,3.167 0.927,0.25 10 false Hall IC 2 5.865,2.958 6.792,3.208 0.927,0.25 10 false Hall IC 2 1.094,1.698 1.365,1.948 0.271,0.25 10 false N 1.896,1.698 2.167,1.948 0.271,0.25 10 false N 0.698,1.698 0.969,1.948 0.271,0.25 10 false S 1.5,1.698 1.771,1.948 0.271,0.25 10 false S 3.885,1.698 4.156,1.948 0.271,0.25 10 false N 4.677,1.698 4.948,1.948 0.271,0.25 10 false N 5.49,1.698 5.76,1.948 0.271,0.25 10 false N 4.281,1.698 4.552,1.948 0.271,0.25 10 false S 5.094,1.698 5.365,1.948 0.271,0.25 10 false S 0.802,3.448 4.323,3.698 3.521,0.25 10 false Torque Sensor Output Characteristics