FUNCTION OF MAIN COMPONENTS
The main components of the entry function have the following functions:
| Component | Function | |
|---|---|---|
|
*1: For sedan models *2: For hatchback models |
||
| Electrical Key Transmitter Sub-assembly | ·
When receiving the request signals that are output by the No. 1 indoor electrical key antenna assembly (center pillar RH, LH), No. 2 indoor electrical key antenna assembly (rear floor), No. 3 indoor electrical key antenna assembly (luggage compartment*1 or back door*2), the key outputs information such as the key ID and vehicle ID. ·
When a driver pushes the lock/unlock button or luggage compartment door opener button*1 on the key, the key outputs a request signal. ·
When receiving the radio wave that is output by the transponder key amplifier in the engine switch, the key outputs information such as the key ID and vehicle ID. ·
Integrates with the mechanical key in order to unlock the doors when the key battery is low. |
|
| Certification ECU (Smart Key ECU Assembly) | ·
Judges and certifies the key. ·
Controls the No. 1 indoor electrical key antenna assembly (center pillar RH, LH), No. 2 indoor electrical key antenna assembly (rear floor) and No. 3 indoor electrical key antenna assembly (luggage compartment*1 or back door*2). ·
Transmits door lock/unlock request signals during the entry function. ·
Transmits steering lock/unlock request signals. ·
Transmits engine immobiliser set/unset request signals. ·
Records codes for verification. |
|
| Body Computer | ·
Receives the request signal from the certification ECU (smart key ECU assembly) and actuates the door lock motors to unlock or lock all the doors, and the luggage compartment door*1. ·
Transmits the condition of each door to the certification ECU (smart key ECU assembly). |
|
| Door Outside Handle Assembly | Lock/Unlock Switch | Transmits the door lock/unlock request signal to the certification ECU (smart key ECU assembly). |
| Luggage Compartment Door Opening Switch Assembly*1 | Transmits a luggage door open request signal to the certification ECU (smart key ECU assembly). | |
| Back Door Opener Switch Assembly*2 | Back Door Opener Switch | Transmits a back door open request signal to the certification ECU (smart key ECU assembly). |
| Back Door Lock Switch | Transmits a door lock request signal to the certification ECU (smart key ECU assembly). | |
| Door Lock Assembly | Door Lock Motor | Drives the motor in response to signals from the body computer and locks or unlocks the doors. |
| Door Lock Position Switch (Front Driver Side) | Detects whether the door is locked or unlocked and sends this information to the body computer. | |
| Door Lock Position Switch (Front Passenger Side, Rear RH, Rear LH) | Detects whether the door is locked or unlocked and sends this information to the certification ECU (smart key ECU assembly). | |
| Luggage Compartment Door Lock Assembly*1 | Door Lock Motor | Drives the motor in response to signals from the body computer and releases the luggage compartment door latch. |
| Courtesy Light Switch | Detects whether the luggage compartment door is open or closed and sends this information to the body computer. | |
| Back Door Lock Assembly*2 | Door Lock Motor | Drives the motor in response to signals from the body computer and releases the back door latch. |
| Courtesy Light Switch | Detects whether the back door is open or closed and sends this information to the body computer. | |
| No. 1 Indoor Electrical Key Antenna Assembly (Center Pillar RH) | Receives a request signal from the certification ECU (smart key ECU assembly), and creates an actuation area around front door RH. | |
| No. 3 Indoor Electrical Key Antenna Assembly (Luggage Compartment)*1 | Receives a request signal from the certification ECU (smart key ECU assembly), and forms an actuation area around the luggage compartment door. | |
| No. 3 Indoor Electrical Key Antenna Assembly (Back Door)*2 | Receives a request signal from the certification ECU (smart key ECU assembly), and forms an actuation area around the back door. | |
| Door Control Receiver | Receives the ID code from the key in the actuation area and transmits it to the certification ECU (smart key ECU assembly). | |
| Door Courtesy Light Switch Assembly | Detects whether the doors are open or closed and sends this information to the body computer. | |
| Wireless Door Lock Buzzer | Sounds to inform the driver of malfunctions in the smart entry and start system. | |
| Combination Meter Assembly | Smart Warning Light | ·
Sounds the buzzer and illuminates the smart warning light in the combination meter according to the activation signal from the certification ECU (smart key ECU assembly). ·
Outputs the vehicle speed signal to the body computer and certification ECU (smart key ECU assembly). ·
Receiving the body computer signals causes the hazard warning light to flash as an answer back. |
| Buzzer | ||
The main components of the start function have the following functions:
| Component | Function | |
|---|---|---|
|
*1: For sedan models *2: For hatchback models *3: Models with automatic transaxle *4: Models with manual transaxle |
||
| Engine Switch | ·
Transmits the engine switch signal to the certification ECU (smart key ECU assembly). ·
Receives the ID code and transmits it to the certification ECU (smart key ECU assembly) when the key battery is low. |
|
| Electrical Key Transmitter Sub-assembly | Receives signals from the antennas and returns the ID code to the door control receiver. | |
| No. 1 Indoor Electrical Key Antenna Assembly (Center Pillar RH, LH) | Receives a request signal from the certification ECU (smart key ECU assembly) and forms an actuation area in the vehicle. | |
| No. 2 Indoor Electrical Key Antenna Assembly (Rear Floor) | ||
| Door Control Receiver | Receives the ID code from the key and transmits it to the certification ECU (smart key ECU assembly). | |
| Certification ECU (Smart Key ECU Assembly) | ·
Changes the power source mode by operating the ACC and IG relays. ·
Controls starting by operating the starter relay assembly. ·
Performs key verification. ·
Controls the No. 1 indoor electrical key antenna assembly (center pillar RH/LH), No. 2 indoor electrical key antenna assembly (rear floor) and No. 3 indoor electrical key antenna assembly (luggage compartment*1 or back door*2). ·
Outputs entry door lock/unlock commands. ·
Outputs steering lock ECU (steering lock actuator assembly) lock/unlock command signals. ·
Outputs immobiliser set/unset commands. ·
Forms the entry detection area. |
|
| Stop Light Switch Assembly*3 | Outputs the state of the brake pedal to the certification ECU (smart key ECU assembly). | |
| ECM | Receives the signal from certification ECU (smart key ECU assembly) and performs engine ignition. | |
| Steering Lock Actuator Assembly | Steering Lock ECU | ·
Receives the command signal from the certification ECU (smart key ECU assembly) and activates the steering lock actuator. ·
Registers the ID verification code. |
| Combination Meter Assembly | Smart Warning Light | Sounds the buzzer and illuminates the smart warning light according to the activation signal from the certification ECU (smart key ECU assembly). |
| Buzzer | ||
| Shift Lock Control Unit Assembly*3 | Shift Lock Control ECU | Outputs the shift position P detection switch signal to the certification ECU (smart key ECU assembly). |
| Park/Neutral Position Switch*3 | Outputs the shift position signal to the certification ECU (smart key ECU assembly). | |
| Clutch Start Switch Assembly*4 | Detects that the clutch pedal is depressed and outputs the signal to the certification ECU (smart key ECU assembly). | |
OPERATING CONDITION
The smart entry and start system is activated only when the key is within the actuation area formed by the 4 indoor electrical key antenna assemblies located within the vehicle.
Each antenna attempts to detect whether the key is within the actuation area and responds with the following actions.
| *A | LHD Models | *B | RHD Models |
| *C | For Sedan Models | *D | For Hatchback Models |
| *1 | No. 1 Indoor Electrical Key Antenna Assembly (Center Pillar RH) | *2 | No. 1 Indoor Electrical Key Antenna Assembly (Center Pillar LH) |
| *3 | No. 2 Indoor Electrical Key Antenna Assembly (Rear Floor) | *4 | No. 3 Indoor Electrical Key Antenna Assembly (Luggage Compartment) |
| *5 | No. 3 Indoor Electrical Key Antenna Assembly (Back Door) | - | - |
| *a | Approximately 0.7 to 1.0 m (27.6 to 39.4 in.) | - | - |
|
Interior Actuation Area |
|
Exterior Actuation Area |
| Actuation Area | Details | |
|---|---|---|
|
*1: For sedan models *2: For hatchback models |
||
| Interior | This actuation area becomes active and the system will attempt to detect the key when any one of the following situations occurs:
·
Driver door is opened or closed ·
Engine switch is pressed while the brake pedal is depressed ·
Warning for the smart entry and start system occurs ·
Lock/unlock switch is pressed |
|
| Exterior | Around Front Door | The range of the actuation area is approximately 0.7 to 1.0 m (27.6 to 39.4 in.) radius from the outside handle of the driver door. When the lock/unlock switch provided on the driver door outside handle is pressed, the actuation area becomes active and the system will attempt to detect key. |
| Around Luggage Compartment Door*1 | The range of the actuation area is approximately 0.7 to 1.0 m (27.6 to 39.4 in.) radius from the center of the luggage compartment door. When the luggage compartment door opening switch is pressed, the actuation area becomes active and the system will attempt to detect key. | |
| Around Back Door*2 | The range of the actuation area is approximately 0.7 to 1.0 m (27.6 to 39.4 in.) radius from the center of the back door. When the back door opener switch or back door lock switch is pressed, the actuation area becomes active and the system will attempt to detect key. | |
FUNCTION
Start Function
The start function has different power source patterns to suit the brake pedal state and shift lever position.
| Pattern | Brake Pedal | Shift Lever | Power Source Pattern |
|---|---|---|---|
| A | Depressed | P or N Position | When the engine switch is pushed once.
·
Off (Lock) → On (IG) (after the engine is started) |
| B | Not Depressed | P Position | Each time the engine switch is pushed.
·
Off (Lock) → On (ACC) → On (IG) → Off (Lock) |
| C | Except P Position | Each time the engine switch is pushed.
·
Off (Lock) → On (ACC) → On (IG) → On (ACC) |
|
| D | - | P Position | When the engine switch is pushed in the On (IG) condition.
·
On (IG) (engine is started or not started) → Off (Lock) |
| E | - | Except P Position | When the engine switch is pushed in the On (IG) condition.
·
On (IG) (engine is started or not started) → On (ACC) |
Normally, the operation of the engine switch is disabled while the vehicle is being driven. However, if the engine must be stopped in an emergency while the vehicle is in motion, the driver can press the engine switch for approximately 2 seconds or more, or press it briefly for 3 times or more in succession to stop the engine.
If no signals are transmitted to the certification ECU (smart key ECU assembly) due to a malfunction in the stop light switch assembly or park/neutral position switch assembly, the engine will not start even if the driver presses the engine switch while depressing the brake pedal. In this case, the driver can start the engine by the following operations. Press the engine switch to turn the power source mode from off (Lock) to on (ACC), and press the engine switch again and hold it for 15 seconds or more.
The above 2 operations must be applied only in emergency situations. Under normal conditions, the engine must not be stopped by pressing the engine switch during driving or started without depressing the brake pedal when the shift lever is in any position other than P or N.
The start function has different power source patterns to suit the clutch pedal (for manual transaxle models).
| Pattern | Clutch Pedal | Power Source Pattern |
|---|---|---|
| A | Depressed | When the engine switch is pushed once.
·
OFF →IG-ON (after the engine is started) |
| B | Not Depressed | Each time the engine switch is pushed.
·
OFF →ACC →IG-ON →OFF |
Normally, the operation of the engine switch is disabled while the vehicle is being driven. However, if the engine must be stopped in an emergency while the vehicle is in motion, the driver can press the engine switch for approximately 2 seconds or more, or press it briefly for 3 times or more in succession to stop the engine.
If no signals are transmitted to the certification ECU (smart key ECU assembly) due to a malfunction in the clutch start switch assembly, the engine will not start even if the driver presses the engine switch while depressing the clutch pedal. In this case, the driver can start the engine by the following operations. Press the engine switch to turn the power source mode from off (Lock) to on (ACC), and press the engine switch again and hold it for 15 seconds or more.
The above 2 operations must be applied only in emergency situations. Under normal conditions, the engine must not be stopped by pressing the engine switch while driving or started without depressing the clutch pedal.
SYSTEM CONTROL
Entry Function
The entry function consists of the following functions:
| Function | Outline |
|---|---|
|
*1: For sedan models *2: For hatchback models |
|
| Wireless Door Lock Control | This function is a convenient system for locking and unlocking all the doors at a distance. The operation of this function in the smart entry and start system is the same as that of the wireless door lock control system. However, the receiver in the certification ECU (smart key ECU assembly) uses a door control receiver to perform the control. |
| Entry Unlock | When a key is located in the exterior actuation area of the outside handle of the driver door, pressing a lock/unlock switch will cause all doors to unlock. |
| Entry Lock*1 | When a key is located in the exterior actuation area of the outside handle of the driver door and the engine switch is off (Lock), all doors can be locked by simply pressing the lock/unlock switch. |
| Entry Lock*2 | When a key is located in the exterior actuation area of the outside handle of the driver door and the engine switch is off (Lock), all doors can be locked by simply pressing the lock/unlock switch, all doors can be locked by simply pressing the lock/unlock switch or pressing the back door lock switch. |
| Luggage Compartment Door Open*1 | When a key is in an exterior actuation area of the of the center of the luggage compartment door, the luggage compartment door can be opened manually by simply pressing the luggage compartment door opening switch. |
| Back Door Open*2 | When a key is in an exterior actuation area of the center of the back door, the back door can be opened manually by simply pressing the back door opener switch. |
| Prevention of Key Confinement | Prevents the confinement of the key if the door is locked from the door outside handle while the key is still inside the vehicle. When locking the doors while the key is inside the vehicle, a buzzer sounds to prevent the key from being confined. |
| Warning | The smart entry and start system causes the certification ECU (smart key ECU assembly) to sound the buzzer in the combination meter assembly and wireless door lock buzzer in order to alert the driver. |
| Battery Saving | When the vehicle remains unused for a long period of time, a battery saving function can prevent discharge of the electrical key transmitter sub-assembly battery. |
| Key Cancel | The following key functions can be cancelled by following certain procedures:
·
Entry unlock/lock ·
Luggage compartment door open*1 ·
Back door open*2 ·
Prevention of key confinement ·
Warning |
| Key Code Registration | A total of 4 keys can be registered. Key registration enables the registering (writing and storing) of transmitter recognition codes in the EEPROM that is contained in the certification ECU (smart key ECU assembly). |
Wireless Door Lock Control Function
The wireless door lock control function has the following functions:
| Function | Outline |
|---|---|
|
*: For sedan models |
|
| All Doors Lock | Pressing the lock button of the electrical key transmitter sub-assembly locks all doors. |
| All Doors Unlock | Pressing the unlock button of the electrical key transmitter sub-assembly unlocks all doors. |
| Luggage Compartment Door Open* | Pressing the luggage compartment door open button of the electrical key transmitter sub-assembly for longer than approximately 0.8 seconds opens the luggage compartment door. |
| Automatic Lock | If none of the doors are opened for approximately 30 seconds after being unlocked by the wireless door lock control, all the doors are locked again automatically. |
| Answer Back | The hazard lights blink once and wireless door lock buzzer sounds once when locking, and blink and sounds twice when unlocking, to inform that the operation has been completed. |
| Door Ajar Warning | If any door is open or ajar, pressing the lock button of the electrical key transmitter sub-assembly will cause the wireless door lock buzzer to sound for about 5 seconds as a warning. |
Entry Unlock
While the user carries the key in the exterior actuation area, and presses the lock/unlock switch of the front door outside handle (Driver Side), the doors are unlocked.
When the doors are unlocked, the hazard warning lights blink twice and the wireless door lock buzzer sounds twice as an answer back.
Entry Lock
When the user gets out of the vehicle while carrying the key and presses the lock/unlock switch of the front door outside handle (Driver Side) within the exterior actuation area with all the doors closed, the doors are locked.
For hatchback models, when the user gets out of the vehicle while carrying the key and presses the back door lock switch within the back door exterior actuation area with all the doors closed, the doors are locked.
| *1 | Back Door Lock Switch | - | - |
When the doors are locked, the hazard warning lights blink once and the wireless door lock buzzer sounds once as an answer back.
Luggage Compartment Door Open (For Sedan Models)
The luggage compartment door is opened when the luggage compartment door opening switch is pressed within the luggage compartment door exterior actuation area while the user is carrying the key.
| *1 | Luggage Compartment Door Opening Switch | - | - |
Back Door Open (For Hatchback Models)
The back door is opened when the back door opener switch is pressed within the back door exterior actuation area while the user is carrying the key.
| *1 | Back Door Opener Switch | - | - |
Warning Function
When any of the situations below occur, the smart entry and start system causes the certification ECU (smart key ECU assembly) to sound a buzzer in the combination meter assembly and the wireless door lock buzzer and illuminate the smart warning light order to alert the driver.
| Situation | Condition |
|---|---|
|
*1: Models with automatic transaxle *2: Models with manual transaxle |
|
| A | The shift lever is in any position other than P and the power source mode is anything other than off (Lock).*1 |
| B | The driver door is opened while the steering is unlocked. |
| C | The shift lever is in P and power source mode is anything other than off (Lock). |
| D | The occupant leaves with the key. |
| E | The engine switch is operated while the key is outside the actuation area. |
| F | The vehicle starts to run without a genuine key in the cabin. |
| G | The entry lock is operated while the key is inside the vehicle. |
| H | The entry lock is operated while any of the doors are open. |
| I | A key is confined inside the vehicle interior. |
| J | The key battery is low. |
| K | The steering lock cannot be released. |
| L | ·
An abnormality that may cause a steering lock actuator malfunction has been detected. ·
An IG relay output circuit error has been detected. ·
A vehicle speed information error has been detected. ·
A clutch start switch assembly malfunction has been detected.*2 |
| M | An electrical key transmitter sub-assembly cannot be detected in the cabin when a door is opened using a mechanical key and the engine switch is pressed, or undetections of an electrical key transmitter sub-assembly in the cabin have occurred 2 times consecutively when the engine switch is pressed. |
| N | An electrical key transmitter sub-assembly is held over the engine switch when the electrical key battery has run out, a smart canceling is performed, or there is a radio interference. |
| O | The engine switch is pressed while the vehicle is being driven. |
There are 2 patterns for situation A. (for automatic transaxle models)
Pattern 1: When the engine is left running and the shift lever is in any position other than P, the driver opens the door and attempts to get out of the vehicle. In this situation, the following control is performed:
| Possible Effects without Warning | Sudden vehicle start, Vehicle theft, Vehicle roll-away | ||
| Warning Active Condition | The warning is activated when all of the following conditions are met:
·
The power source mode is in a mode other than off (Lock). ·
The shift lever is in any position except P. ·
The driver door is opened. ·
The vehicle speed is 0 km/h (0 mph). |
||
| Warning Method | Combination Meter Assembly | Buzzer | Sounds continuously |
| Smart Warning Light | - | ||
| Wireless Door Lock Buzzer | - | ||
| Warning Stop Condition | The warning is stopped when one of the following conditions is met:
·
The power source mode is off (Lock). ·
The shift lever is in P. ·
The driver door is closed. ·
The vehicle speed is above 5 km/h (3 mph). |
||
Pattern 2: Under the conditions of pattern 1, the driver closes the door and attempts to leave the vehicle holding the electrical key transmitter sub-assembly. In this situation, the following control is performed:
| Possible Effects without Warning | Sudden vehicle start, Vehicle theft, Vehicle roll-away | ||
| Warning Active Condition | The warning is activated when all of the following conditions are met:
·
The power source mode is in a mode other than off (Lock). ·
The shift lever is in any position except P. ·
The driver door is opened→closed. ·
The electrical key transmitter sub-assembly is not detected in the vehicle. ·
The vehicle speed is 0 km/h (0 mph). |
||
| Warning Method | Combination Meter Assembly | Buzzer | Sounds continuously |
| Smart Warning Light | Blinks yellow | ||
| Wireless Door Lock Buzzer | Sounds continuously | ||
| Warning Stop Condition | Combination Meter Assembly | Buzzer | ·
The power source mode is off (Lock). ·
The shift lever is moved to P. ·
The vehicle speed is above 5 km/h (3 mph). ·
The electrical key transmitter sub-assembly is detected in the vehicle. |
| Wireless Door Lock Buzzer | |||
| Combination Meter Assembly | Smart Warning Light | ·
The power source mode is off (Lock). ·
The electrical key transmitter sub-assembly is detected in the vehicle. |
|
In situation B: If the driver door is opened while the steering is unlocked, the following control is performed.
| Possible Effects without Warning | Vehicle theft | ||
| Warning Active Condition | The warning is activated when one of the following conditions is met:
·
The power source mode is on (ACC) and the driver's door is opened. ·
The power source mode is off (Lock) and steering is unlocked and driver door is opened. |
||
| Warning Method | Combination Meter Assembly | Buzzer | Intermittently sounds |
| Smart Warning Light | - | ||
| Wireless Door Lock Buzzer | - | ||
| Warning Stop Condition | The warning is stopped when one of the following conditions is met:
·
The power source mode is on (IG). ·
The driver's door is closed. ·
The power source mode is off (Lock) and steering is locked. |
||
There are 2 patterns for situation C.
Pattern 1: When the engine is left running and the shift lever is in the P position, the driver closes the driver's door and attempts to leave the vehicle while holding the electrical key transmitter sub-assembly. In this situation, the following control is performed:
| Possible Effects without Warning | Vehicle theft | ||
| Warning Active Condition | The warning is activated when all of the following conditions are met:
·
The power source is in a mode other than OFF ·
The shift lever is in P. (for automatic transaxle models) ·
The driver door is opened→closed. ·
The electrical key transmitter sub-assembly is not detected in the vehicle. ·
The vehicle speed is 0 km/h (0 mph). |
||
| Warning Method | Combination Meter Assembly | Buzzer | Sounds once |
| Smart Warning Light | Blinks yellow | ||
| Wireless Door Lock Buzzer | Sounds 3 times | ||
| Warning Stop Condition | The warning is stopped when one of the following conditions is met:
·
The power source mode is off (Lock). ·
The electrical key transmitter sub-assembly is detected in the vehicle. |
||
Pattern 2: Under the conditions of pattern 1, the driver presses the lock/unlock switch on the door outside handle. In this situation, the following control is performed:
| Possible Effects without Warning | Vehicle theft | ||
| Warning Active Condition | The warning is activated when all of the following conditions are met:
·
The power source is in a mode other than OFF ·
The shift lever is in P. (for automatic transaxle models) ·
The electrical key transmitter sub-assembly is not detected in the vehicle. ·
The electrical key transmitter sub-assembly is detected in an outside detection area. ·
The vehicle speed is 0 km/h (0 mph). ·
The lock/unlock switch is pressed. |
||
| Warning Method | Combination Meter Assembly | Buzzer | Sounds once |
| Smart Warning Light | Blinks yellow | ||
| Wireless Door Lock Buzzer | Sounds for 5 seconds | ||
| Warning Stop Condition | Combination Meter Assembly | Smart Warning Light | ·
The power source mode is off (Lock). ·
The electrical key transmitter sub-assembly is detected in the vehicle. |
| Wireless Door Lock Buzzer | ·
The power source mode is off (Lock). ·
The shift lever is in any position except P. ·
The vehicle speed is above 5 km/h (3 mph). ·
The electrical key transmitter sub-assembly is detected in the vehicle. ·
Any door is opened or closed. |
||
In situation D: When the engine is left running and when a passenger gets out of the vehicle holding the electrical key transmitter sub-assembly, the following control is performed.
| Possible Effects without Warning | Engine cannot be restarted | ||
| Warning Active Condition | The warning is activated when all of the following conditions are met:
·
The power source mode is anything other than off (Lock). ·
A door other than the driver door is opened→closed. ·
The electrical key transmitter sub-assembly is not detected in the vehicle. ·
The vehicle speed is 0 km/h (0 mph). |
||
| Warning Method | Combination Meter Assembly | Buzzer | Sounds once |
| Smart Warning Light | Blinks yellow | ||
| Wireless Door Lock Buzzer | Sounds 3 times | ||
| Warning Stop Condition | The warning is stopped when one of the following conditions is met:
·
The power source mode is off (Lock). ·
The electrical key transmitter sub-assembly is detected in the vehicle. |
||
In situation E: When the electrical key transmitter sub-assembly is not within the actuation areas, the following control is performed.
| Possible Effects without Warning | User becomes confused | ||
| Warning Active Condition | The warning is activated when all of the following conditions are met:
·
The engine immobiliser has been set. ·
The electrical key transmitter sub-assembly is not detected in the vehicle. ·
The engine switch is pushed. |
||
| Warning Method | Combination Meter Assembly | Buzzer | Sounds once |
| Smart Warning Light | Blinks yellow | ||
| Wireless Door Lock Buzzer | - | ||
| Warning Stop Condition | The warning is stopped when one of the following conditions is met:
·
Smart warning light illuminates for 15 seconds. ·
The electrical key transmitter sub-assembly is detected again or returned to the vehicle. |
||
In situation F: When the vehicle starts moving without a registered electrical key transmitter sub-assembly in the vehicle, the following control is performed.
| Possible Effects without Warning | Engine cannot be restarted | ||
| Warning Active Condition | The warning is activated when all of the following conditions are met:
·
The power source mode is on (IG). ·
During the key taken away alarm. ·
The vehicle speed is above 5 km/h (3 mph). ·
The electrical key transmitter sub-assembly is not detected in the vehicle. |
||
| Warning Method | Combination Meter Assembly | Buzzer | Sounds 9 times |
| Smart Warning Light | Blinks yellow | ||
| Wireless Door Lock Buzzer | - | ||
| Warning Stop Condition | The warning is stopped when one of the following conditions is met:
·
Power source mode is off (Lock). ·
The electrical key transmitter sub-assembly is detected in the vehicle. |
||
In situation G: When the electrical key transmitter sub-assembly is left in the vehicle interior and the lock/unlock switch is pressed, the following control is performed.
| Possible Effects without Warning | Vehicle theft | ||
| Warning Active Condition | The warning is activated when all of the following conditions are met:
·
The power source mode is off (Lock). ·
All doors are closed. ·
The electrical key transmitter sub-assembly is detected in the vehicle. ·
The lock/unlock switch is pressed. ·
Any door is unlocked. ·
The vehicle speed is 0 km/h (0 mph). |
||
| Warning Method | Combination Meter Assembly | Buzzer | - |
| Smart Warning Light | - | ||
| Wireless Door Lock Buzzer | Sounds for 5 seconds | ||
| Warning Stop Condition | The warning is stopped when one of the following conditions is met:
·
Power source mode is anything other than off (Lock). ·
Lock operation is detected. ·
Any door is opened. ·
The vehicle speed is above 5 km/h (3 mph). |
||
In situation H: When any door is ajar, and the locking of the doors is attempted through the entry lock function by pressing the lock/unlock switch of a door outside handle, the following control is performed.
| Possible Effects without Warning | Vehicle theft | ||
| Warning Active Condition | The warning is activated when all of the following conditions are met:
·
The power source mode is off (Lock). ·
Any door is opened. ·
The lock/unlock switch is pressed, or the lock switch is pressed on the electrical key transmitter sub-assembly. ·
The electrical key transmitter sub-assembly is in an outside detection area. |
||
| Warning Method | Combination Meter Assembly | Buzzer | - |
| Smart Warning Light | - | ||
| Wireless Door Lock Buzzer | Sounds for 5 seconds | ||
| Warning Stop Condition | The warning is stopped when one of the following conditions is met:
·
Power source mode is any mode other than off (Lock). ·
Doors are unlocked through the wireless door lock control function. ·
An entry unlock operation is performed. ·
All doors are closed. |
||
In situation I: When a key is confined inside the vehicle interior, the following control is performed.
| Possible Effects without Warning | Vehicle theft | ||
| Warning Active Condition | The warning is activated when all of the following conditions are met:
·
There is a key less lock operation. ·
The electrical key transmitter sub-assembly is detected in the vehicle. ·
The vehicle speed is 0 km/h (0 mph). |
||
| Or, the warning is activated when all of the following conditions are met:
·
Power source mode is off (Lock). ·
All doors are closed and locked. ·
There is a lock operation using other than entry function. ·
The electrical key transmitter sub-assembly is detected in the vehicle. |
|||
| Warning Method | Combination Meter Assembly | Buzzer | Sounds once |
| Smart Warning Light | - | ||
| Wireless Door Lock Buzzer | Sounds for 5 seconds | ||
| Warning Stop Condition | The warning is stopped when one of the following conditions is met:
·
The power source mode is switched. ·
Doors are locked through the manual lock, wireless door lock function, or key-linked lock operation. ·
Any door is opened. ·
The vehicle speed is above 5 km/h (3 mph). |
||
In situation J: When the key battery is low, the following control is performed.
| Possible Effects without Warning | Smart entry and start system will not function, engine cannot be restarted | ||
| Warning Active Condition | The warning is activated when all of the following conditions are met:
·
After the power source mode has been on (IG) continuously for approximately 20 minutes or more, it is changed from on (IG) to off (Lock). ·
The key battery voltage is low. ·
The electrical key transmitter sub-assembly is in the vehicle. ·
The vehicle speed is 0 km/h (0 mph). |
||
| Or, the warning is activated when all of the following conditions are met:
·
The engine is started from the stopped status. ·
The key battery voltage is low. ·
The electrical key transmitter sub-assembly is in the vehicle. ·
The vehicle speed is 0 km/h (0 mph). ·
After approximately 20 minutes had elapsed and the engine switch was turned on, there is an occurrence result of the key battery drop warning when the engine switch is turned off (Lock). |
|||
| Warning Method | Combination Meter Assembly | Buzzer | Sounds once |
| Smart Warning Light | Blinks yellow | ||
| Wireless Door Lock Buzzer | - | ||
| Warning Stop Condition | The warning is stopped when all of the following conditions are met:
·
Approximately 15 seconds have elapsed from the time the warning started. ·
The vehicle speed is above 5 km/h (3 mph). |
||
In situation K: When steering lock does not release, the following control is performed.
| Possible Effects without Warning | Steering usability function | ||
| Warning Active Condition | The steering lock does not release, thus the engine is prevented from starting. | ||
| Warning Method | Combination Meter Assembly | Buzzer | Sounds once |
| Smart Warning Light | Blinks green rapidly for 15 seconds | ||
| Wireless Door Lock Buzzer | - | ||
| Warning Stop Condition | The system returns to normal. | ||
In situation L: When all of the following conditions are met, the following control is performed.
An abnormality that may cause a steering lock actuator malfunction has been detected.
An IG relay output circuit error has been detected.
A vehicle speed information error has been detected.
A clutch start switch assembly malfunction has been detected.*
|
*: Models with manual transaxle |
|||
| Possible Effects without Warning | Trouble detection | ||
| Warning Active Condition | The warning is activated when all of the following conditions are met:
·
A steering lock actuator internal abnormality, a certification ECU (smart key ECU assembly) internal abnormality, or a steering lock unlock position switch malfunction has been detected. ·
IG relay output circuit errors have occurred 3 times consecutively. ·
A vehicle speed abnormal judgment or communication vehicle speed signal interruption has been detected. ·
Power source mode is off(Lock), clutch start switch assembly remains ON for 5 minutes or more, and driver door is closed → opened.* |
||
| Warning Method | Combination Meter Assembly | Buzzer | Sounds once |
| Smart Warning Light | Blinks in yellow for 15 seconds | ||
| Wireless Door Lock Buzzer | - | ||
| Warning Stop Condition | Errors have been resolved. | ||
In situation M: When an electrical key transmitter cannot be detected in the cabin when a door is opened using a mechanical key and the engine switch is pressed, or undetections of an electrical key transmitter sub-assembly in the cabin have occurred 2 times consecutively when the engine switch is pressed, the following control is performed.
| Possible Effects without Warning | Smart entry and start system will not function | ||
| Warning Active Condition | The warning is activated when all of the following conditions are met:
·
The engine switch is pushed. ·
The engine immobiliser has been set. ·
The electrical key transmitter sub-assembly is not detected in the vehicle. ·
There is a mechanical key unlock history or there are 2 consecutive verification errors when the engine switch is turned on. |
||
| Warning Method | Combination Meter Assembly | Buzzer | Sounds once |
| Smart Warning Light | Blinks yellow | ||
| Wireless Door Lock Buzzer | - | ||
| Warning Stop Condition | The warning is stopped when one of the following conditions is met:
·
Approximately 60 seconds have elapsed from the time the warning started. ·
The electrical key transmitter sub-assembly is detected in the vehicle. |
||
In situation N: When an electrical key transmitter sub-assembly is held over the engine switch when the electrical key battery has run out, a smart canceling is performed, or there is a radio disturbance, the following control is performed.
| Possible Effects without Warning | Smart entry and start system will not function | ||
| Warning Active Condition | Transponder verification accepted | ||
| Warning Method | Combination Meter Assembly | Buzzer | Sounds once |
| Smart Warning Light | - | ||
| Wireless Door Lock Buzzer | - | ||
In situation O: When warning buzzer sounds when engine switch operated while driving, the following control is performed.
| Possible Effects without Warning | Prevent accidental operation | ||
| Warning Active Condition | The warning is activated when all of the following conditions are met:
·
The engine is running at 200 rpm or more. ·
The vehicle speed is 5 km/h (3.11 mph) or more. ·
The engine switch is pressed. |
||
| Warning Method | Combination Meter Assembly | Buzzer | Sounds continuously |
| Smart Warning Light | - | ||
| Wireless Door Lock Buzzer | - | ||
| Warning Stop Condition | The warning is stopped when one of the following conditions is met:
·
1.8 seconds have elapsed after operation of the engine switch is stopped. ·
The engine switch is turned off. |
||
Battery Saving Function of Electrical Key Transmitter Sub-assembly
This function cancels the signal reception waiting state of the electrical key transmitter subassembly, reducing the consumption of current from its battery.
The electrical key transmitter sub-assembly can be placed into and taken out of battery saving mode. When the electrical key transmitter sub-assembly is in battery saving mode, the smart entry and start system will not be able to detect the transmitter, as the transmitter will not respond to signals from the vehicle. The function of the smart entry and start system will not operate if the electrical key transmitter sub-assembly is in battery saving mode.
Pressing the unlock switch of the electrical key transmitter sub-assembly twice while pressing the lock switch (the indicator light of the electrical key transmitter sub-assembly blinks 4 times) selects battery saving mode for the electrical key transmitter sub-assembly.
Battery saving mode can be canceled by pressing any switch on the electrical key transmitter sub-assembly.
Key Cancel Function
A key cancel function is provided to make it possible to disable the smart entry and start system. Key cancel can be operated when certain operations are performed when the vehicle is under the following conditions:
Engine switch is off (Lock).
Driver door is closed.
Driver door is unlocked.
The operation procedure is as follows:
Press the unlock button of the electrical key transmitter sub-assembly.
Open the driver door within 5 seconds of completing the step above (driver door: closed condition → opened).
With the driver door open, press the unlock button of the electrical key transmitter sub-assembly 2 times within 5 seconds of completing the step above.
If the driver door is closed before or while pressing the unlock button, the entry cancel setting mode will end.
Finish the steps (a) to (c) within 30 seconds of completing the step above.
Close and open the driver door twice (driver door: open condition → closed → opened → closed → opened).
With the driver door open, press the unlock button of the electrical key transmitter sub-assembly 2 times.
If the driver door is closed before or while pressing the unlock button, the entry cancel setting mode will end.
Close and open the driver door (driver door: open condition → closed → opened).
Close the driver door within 5 seconds of completing the above step.
Check that the wireless buzzer sounds twice (short beeps) to confirm that the smart entry and start system has been canceled.
Key Code Registration Function
The table below shows the 3 special ID code registration function modes through which up to 4 different transmitter recognition codes can be registered. The codes are electronically registered (written to and stored) in the EEPROM. For details, refer to the corresponding Service Bulletin for this model.
| Mode | Mode Function |
|---|---|
| Rewrite | Clears all previously registered codes and registers only the newly received codes. This mode is used whenever a transmitter or the certification ECU (smart key ECU assembly) is replaced. |
| Add | Adds a newly received code while preserving previously registered codes. This mode is used when adding a new transmitter. If the number of codes exceeds 4, the oldest registered code is cleared first. |
| Confirm | Confirms how many codes are currently registered. When adding a new code, this mode is used to check how many codes already exist. |
DIAGNOSIS
The certification ECU (smart key ECU assembly) can detect malfunctions in the smart entry and start system when the power source is on (IG).
When the ECU detects a malfunction, the smart warning light blinks in yellow to warn the driver. At the same time, the ECU stores a 5-digit Diagnostic Trouble Code (DTC) in its memory.
The 5-digit DTCs can be read after connecting the Global TechStream (GTS) to the DLC3.
The smart entry and start system may not operate successfully if a malfunction occurs.
For details, refer to the Repair Manual.