Home › Engine / Hybrid System › 1NZ-FE ENGINE MECHANICAL › ENGINE UNIT › 2014.03–2016.07
NM30M0E _51 Engine / Hybrid System _018285 1NZ-FE ENGINE MECHANICAL _0090362 ENGINE UNIT GE GENERAL F

1NZ-FE ENGINE MECHANICAL  ENGINE UNIT  GENERAL  GENERAL  


OUTLINE


a.

The 1NZ-FE engine is a 1.5-liter, 16-valve DOHC, in-line 4-cylinder gasoline engine.


b.

The Variable Valve Timing-intelligent (VVT-i) system, Direct Ignition System (DIS) and Electronic Throttle Control System-intelligent (ETCS-i) are used on this engine in order to realize high performance, quietness, fuel economy and clean emission.

Models without Air Fuel Ratio Sensor
W111019

Models with Air Fuel Ratio Sensor
W115933



SPECIFICATION


Engine Type 1NZ-FE
No. of Cyls. and Arrangement 4-cylinder, In-line
Valve Mechanism 16-valve DOHC, Chain Drive (with VVT-i)
Combustion Chamber Pentroof Type
Flow of Intake and Exhaust Gasses Cross-Flow
Fuel System SFI
Ignition System DIS
Displacement 1497 cm3 (91.3 cu. in.)
Bore x Stroke 75.0 mm x 84.7 mm (2.95 in. x 3.33 in.)
Compression Ratio 10.5:1
Max. Output EEC 80 kW @ 6000 rpm
Max. Torque EEC 141 N*m @ 4200 rpm
Valve Timing Intake Open 33°BTDC to 7°ATDC
Closed 12°ABDC to 52°ABDC
Exhaust Open 42°BBDC
Closed 2°ATDC
Firing Order 1 - 3 - 4 - 2
Fuel Unleaded Gasoline
Research Octane Number (RON) 91 or higher
Oil Grade API grade SL "Energy-Conserving", SM "Energy-Conserving", SN "Resource-Conserving" or ILSAC multigrade engine oil
Emission Regulation EURO 5*1
EURO 4*2
Engine Service Mass*3 (Reference) M/T 89.6 kg (197.5 lb)
A/T 79.6 kg (175.5 lb)

HINT:

*1: Models with air fuel ratio sensor

*2: Models without air fuel ratio sensor

*3: Weight shows the figure with oil fully filled.


W111020E01
0.125,0.083 1.958,0.344 1.833,0.26 12 false Performance Curve: 2.99,4.448 4.406,4.698 1.417,0.25 10 false Engine Speed (rpm) 4.573,4.01 4.917,4.24 0.344,0.229 10 false 7000 4.208,4.01 4.552,4.24 0.344,0.229 10 false 6000 3.833,4.01 4.177,4.24 0.344,0.229 10 false 5000 3.104,4.01 3.448,4.24 0.344,0.229 10 false 3000 3.469,4.01 3.813,4.24 0.344,0.229 10 false 4000 2.729,4 3.073,4.229 0.344,0.229 10 false 2000 2.365,4 2.708,4.229 0.344,0.229 10 false 1000 5.688,1.802 6.521,2.219 0.833,0.417 10 false Output (kW) 0.521,1.521 1.354,1.938 0.833,0.417 10 false Torque (N*m) 5.229,0.729 5.427,0.979 0.198,0.25 10 false 80 5.208,1.469 5.406,1.719 0.198,0.25 10 false 60 5.208,1.094 5.406,1.344 0.198,0.25 10 false 70 5.219,0.333 5.417,0.583 0.198,0.25 10 false 90 5.208,1.802 5.406,2.052 0.198,0.25 10 false 50 5.208,2.167 5.406,2.417 0.198,0.25 10 false 40 5.188,2.542 5.385,2.792 0.198,0.25 10 false 30 5.188,3.271 5.385,3.521 0.198,0.25 10 false 10 5.198,2.906 5.396,3.156 0.198,0.25 10 false 20 5.208,3.635 5.406,3.885 0.198,0.25 10 false 0 1.708,0.844 1.99,1.052 0.281,0.208 10 false 150 1.698,1.198 1.979,1.406 0.281,0.208 10 false 130 1.698,1.021 1.979,1.229 0.281,0.208 10 false 140 1.698,1.375 1.979,1.583 0.281,0.208 10 false 120 1.698,1.552 1.979,1.76 0.281,0.208 10 false 110 1.781,1.906 1.969,2.115 0.188,0.208 10 false 90 1.708,1.729 1.99,1.938 0.281,0.208 10 false 100 1.781,2.083 2.01,2.292 0.229,0.208 10 false 80


MAIN FEATURES


a.

The 1NZ-FE engine has achieved the following performance through the use of the items listed below.

(1) High performance and reliability

(2) Low noise and vibration

(3) Lightweight and compact design

(4) Good serviceability

(5) Clean emission and fuel economy


Section Item (1) (2) (3) (4) (5)
Engine Control System The Electronic Throttle Control System-intelligent (ETCS-i) is used. ○ - - - ○
A non-contact sensor is used in the throttle position sensor and accelerator pedal position sensor. ○ - - - -
Engine Proper An aluminum cylinder block sub-assembly is used. - - ○ - -
An offset crankshaft is used. ○ ○ - - ○
A taper squish shape is used for the top of the pistons. ○ - - - ○
Valve Mechanism A chain sub-assembly and No. 1 chain tensioner assembly are used. ○ - ○ ○ -
The Variable Valve Timing-intelligent (VVT-i) system is used. ○ - - - ○
Fuel System 12-hole type fuel injector assemblies are used. ○ - - - ○
A fuel returnless system is used. - - ○ ○ ○
Quick connectors are used to connect the fuel hoses and fuel pipes. - - - ○ -
Intake and Exhaust System A plastic intake manifold is used. - - ○ - -
A linkless type throttle body with motor assembly is used. - - ○ ○ -
A stainless steel exhaust manifold is used. - - ○ - -
2 Three-Way Catalytic converters (TWCs) are used. - - - - ○
A rearward exhaust layout is used. - - - - ○
Ignition System The Direct Ignition System (DIS) is used. ○ - - ○ ○