FUNCTION OF MAIN COMPONENTS
The main components of the K411 Continuously Variable Transaxle (CVT) are as follows:
| Component | Function | |
|---|---|---|
|
*: Models with air conditioning system |
||
| Continuously Variable Transaxle Assembly | Duty Solenoid Valve DS1 (for Shift Control) | Controls the fluid flow volume to the primary pulley in accordance with the vehicle speed and accelerator pedal position (speed control during acceleration). |
| Duty Solenoid Valve DS2 (for Shift Control) | ||
| Linear Solenoid Valve SLU (for Lock-up Control) | Controls the engagement oil pressure of the lock-up clutch. | |
| Linear Solenoid Valve SLT (for Line Pressure Control) | ·
Controls the line pressure. ·
Controls the engagement oil pressure of the forward clutch and reverse brake. |
|
| Linear Solenoid Valve SLS (for Belt Clamping Force Control) | ·
Controls the oil pressure of the secondary pulley. ·
Controls the line pressure upon engagement of the forward clutch and reverse brake. |
|
| Transmission Revolution Sensor (NIN) | Detects the primary pulley speed (input speed). | |
| Transmission Revolution Sensor (NOUT) | Detects the secondary pulley speed (output speed). | |
| Transmission Revolution Sensor (NT) | Detects the turbine speed of the torque converter. | |
| CVT Fluid Temperature Sensor | Detects the CVT fluid temperature. | |
| Oil Pressure Sensor | Detects the steel belt clamping force. | |
| E.F.I. Engine Coolant Temperature Sensor | Detects the engine coolant temperature. | |
| Throttle Body with Motor Assembly | Throttle Position Sensor | Detects the opening angle of the throttle valve. |
| Deceleration Sensor | Detects the tilt angle of the vehicle. | |
| Stop Light Switch Assembly | Detects the brake pedal depressing signal. | |
| Park/Neutral Position Switch Assembly | Detects the shift lever position. | |
| Shift Lock Control Unit Assembly | Transmission Control Switch | ·
Detects that the shift lever is in M. ·
Detects the driver's shift-up and shift-down operations when the shift lever is in M. |
| Crank Position Sensor | Detects the engine speed. | |
| Accelerator Pedal Sensor | Detects the accelerator pedal opening angle. | |
| Air Conditioning Amplifier Assembly* | Transmits the operating state of the air conditioning system to the ECM. | |
| ECM | Drives each solenoid valve based on signals from each sensor and switch and optimally controls the CVT. | |
| Combination Meter Assembly | Shift Position Indicator | Indicates the shift lever position. |
| Malfunction Indicator Lamp (MIL) | Illuminates or blinks to inform the driver when the ECM detects a malfunction. | |
SYSTEM CONTROL
Control List
The electronic control system of the K411 CVT consists of the controls listed below.
| Control | Outline |
|---|---|
| Engine-CVT Integrated Control | Effects coordinated control of the CVT system and engine control system to ensure both smooth and powerful driving that excels in shift response and fuel economy. |
| Automatic Shift Control (Speed Ratio Control) | Controls the primary pulley speed to approach the calculated target input rotation speed based on information such as the accelerator pedal position, vehicle speed and stop light switch signals. |
| Acceleration Improvement Control | Controls the acceleration rate in proportion to the accelerator pedal position, improving the feeling of linear acceleration and expanding the feeling of accelerator pedal input. |
| Uphill/Downhill Shift Control | Uses the ECM to determine whether the vehicle is traveling uphill or downhill in order to restrict upshifts or provide appropriate engine braking force by restricting downshifts. |
| Lock-up Control | By enhancing the lock-up operation range into the low vehicle speed range, the fuel cut range has been enlarged, achieving improved fuel economy. |
| Flex Lock-up Control | |
| 7-speed Sport Sequential Shiftmatic | Enables driving in a gear step selected using the shift lever, providing engine braking force appropriate to each gear step. |
Engine - CVT Integrated Control
To effect fine-tuned control in accordance with driving conditions, various signals are exchanged between the engine control system and the CVT system. As a result, both smooth and powerful driving that excels in shift response and fuel economy has been achieved.
Automatic Shift Control (Speed Ratio Control)
The ECM determines the driving conditions through each input signal and selects the optimal control to achieve output which meets the driver's intentions.
The ECM calculates the target primary pulley speed in accordance with the accelerator pedal position signal, vehicle speed signal, and stop light switch signal, in order to attain an optimal pulley ratio and shifting speed. To allow the actual primary pulley speed (acquired from the primary speed sensor) to match the target primary pulley speed, the ECM actuates duty solenoid valves DS1 and DS2 in order to control the inflow and outflow volume of line pressure to and from the primary pulley. As a result, optimal pulley ratio and shifting speed have been achieved.
When the shift lever is in D, the system effects engine integrated control to optimize fuel economy characteristics and driving performance.
When the shift lever is in M, the shift characteristic is as shown below. The system will upshift automatically when the vehicle reaches the set speed during acceleration.
Acceleration Improvement Control
The system determines the driver's acceleration request based on the vehicle speed and changes in the accelerator pedal position. When the system determines this request, it will change the shift characteristics to ones in which the engine speed and vehicle speed increase linearly, providing improved acceleration feeling.
Uphill/Downhill Shift Control
Uphill/downhill shift control helps perform optimal shifting while driving on a winding uphill or downhill road.
When the ECM determines the vehicle is traveling uphill, the control restricts upshifting, thus offering smooth driving.
If a signal indicating that the driver has operated the brake pedal is input when the ECM has determined the vehicle is traveling downhill, the control downshifts to generate optimal engine braking force.
The actual acceleration calculated from the vehicle speed signal is compared with the reference acceleration (based on level road travel) stored in the ECM to determine uphill or downhill travel.
| *a | Uphill | *b | Downhill |
| *c | Smaller | *d | Greater |
|
Reference Acceleration |
|
Actual Acceleration |
Lock-up Control
The lock-up operation range has been expanded from that of previous continuously variable transaxles, thus enabling control to start from low speeds.
The lock-up operation range during deceleration has been expanded to the low-speed range. This expands the fuel cut range and achieves excellent fuel economy.
Flex Lock-up Control
In order to improve the transmission efficiency and also the fuel economy, the linear solenoid valve SLU for lock-up engagement pressure control is employed to deliver flex lock-up control that can provide more precise control than that of a conventional lock-up clutch mechanism.
Flex lock-up control during deceleration is used to expand the fuel-cut range. It operates the lock-up clutch over the low vehicle speed range when the vehicle decelerates so that minimal speed difference between the engine speed and turbine speed can be maintained.
7-speed Sport Sequential Shiftmatic
The driver can select the desired gear step by moving the shift lever to "+" (forward) or to "-"(backward) while the shift lever is in M (7-speed sport sequential shiftmatic mode). Thus, the driver is able to change gear steps with a manual-like feel.
7-speed sport sequential shiftmatic mode can be selected from normal driving mode by moving the shift lever to M. The driver can change the gear step by selecting it using the shift lever, and engine braking force is provided in accordance with the selected gear step.
Through the engine-CVT integrated control, pulley ratio and engine torque which corresponds to shifting speed are finely controlled, thus improving shifting response and achieving a reduction in shifting shock.
The shift position and shift range indicator is provided in the multi-information display of the combination meter assembly. When the shift lever is in P, R, N or D, the shift position is indicated in the shift position and shift range indicator. When the shift lever is in M, "M" and the selected shift range are displayed in the shift position and shift range indicator.
| *a | When shift lever is in P, R, N or D | *b | When shift lever is in M |
In 7-speed sport sequential shiftmatic mode, the transmission automatically upshifts or downshifts under the following conditions:
| Condition | System Control |
|---|---|
| Engine is under-revving. | 1 step downshift |
| Engine is over-revving. | 1 step upshift |
When the vehicle is stopped during 7-speed sport sequential shiftmatic mode, the transmission automatically downshifts to M1.
The ECM will restrict the changing of the gear step if it detects a malfunction in the CVT system.
If the vehicle speed and engine speed exceeds or goes below a preset level in response to the driver's downshift operation request, changing the gear step will be prohibited. In this case, the buzzer in the combination meter will sound to alert the driver.
FAIL-SAFE
This function minimizes the loss of operability when a malfunction occurs in any sensor or shift solenoid valve.
For details, refer to the Repair Manual.
DIAGNOSIS
When the ECM detects a malfunction, it records the malfunction and information related to the fault. Furthermore, the ECM will illuminate or blink the MIL in the combination meter to inform the driver.
At the same time, the Diagnostic Trouble Codes (DTCs) are stored in memory. The DTCs can be read by connecting the Global TechStream (GTS) to the DLC3. For details, refer to the Repair Manual.