Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2016.04–2016.10
NM30M0E _58 Vehicle Interior _018323 METER / GAUGE / DISPLAY _0090314 METER / GAUGE SYSTEM CO CONTROL F

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  CONTROL  COMBINATION METER  


OPERATING CONDITION


a.

Eco Driving Indicator Light (Models with Automatic Transaxle or CVT)

i.

Eco Driving Indicator Light starts to operate when the following conditions are met:

Condition
·

Ignition switch is ON.

·

Engine is running.

·

Shift lever is in D.

·

When the vehicle is at a speed of 130 km/h (81 mph) or below




ii.

Eco Driving Indicator Light stops operation when any of the following conditions is met:

Condition
·

Ignition switch is off.

·

Engine is stopped.

·

Shift lever is in any position other than D

·

When the vehicle is at a speed of 130 km/h (81 mph) or over.






SYSTEM CONTROL


a.

Front Seat Belt Warning (Models for the regions except for G.C.C. Countries)

i.

When the ignition switch is ON, this system detects the state of the seat belt based on the signal from the driver seat belt buckle switch.


ii.

The front seat belt warning light located in the combination meter is used for the driver seat.


iii.

After the ignition switch is turned ON, if the driver has not fastened the seat belt, the seat belt warning light will begin flashing.


iv.

When the seat belt remains unfastened and the vehicle speed reaches approximately 20 km/h (12.4 mph), the seat belt warning buzzer will start sounding intermittently. At this time, the seat belt warning light flashing will change in sync with the intermittent buzzer sound. These buzzer and indicator warnings will continue for approximately 30 seconds until the seat belt is fastened.


v.

If the seat belt still remains unfastened over the approximately 30 seconds, the intervals of the intermittent buzzer sound and flashing light will change. Until the seat belt is fastened, the intermittent buzzer sound will be extended for approximately 90 seconds and the warning light will continue flashing.


vi.

While the seat belt warning light and buzzer are operating, fastening the seat belt will bring them to a stop.



b.

Front Seat Belt Warning (Models for G.C.C. Countries)

i.

When the ignition switch is ON, this system detects the state of the seat belts based on the signals from the driver seat belt buckle switch.


ii.

The front seat belt warning light located in the combination meter is used for the driver seat.


iii.

After the ignition switch is turned ON, if the driver's seat belt has remained unfastened for 1.8 seconds, the front seat belt warning light will flash for 6 seconds. And then, when either of the following conditions is met, the seat belt warning light will continue flashing:

·

The driver's seat belt remains unfastened, and the vehicle is in a condition other than the conditions described below for approximately 30 seconds or more: The vehicle speed is 0km/h with the shift lever in P or the parking brake applied.

·

The driver's seat belt remains unfastened, and the seat belt warning buzzer sounds just once.


Furthermore, when the seat belt is not fastened within approximately 30 seconds from the time the seat belt warning buzzer started sounding periodically, the warning light will commence flashing at short intervals.


iv.

If the driver's seat belt is still unfastened even after the ignition switch is turned ON, the seat belt warning buzzer will sound 5 times. And then, if the driver's seat belt remains unfastened and the vehicle speed reaches approximately 20 km/h (12.4 mph), the seat belt warning buzzer will sound once. Furthermore, when approximately 30 seconds has elapsed with the seat belt unfastened, the seat belt warning buzzer will start sounding periodically for 9.6 seconds. If the seat belt is not fastened within this 9.6 seconds, the seat belt warning buzzer will commence sounding at short intervals.


v.

While the seat belt warning light is flashing and the seat belt warning buzzer is sounding, fastening the seat belt will bring the warning light flashing and warning buzzer sounding to a stop.



c.

Eco Driving Indicator Light (Models with Automatic Transaxle or CVT)

i.

When the ECM determines that Eco driving (environment-friendly acceleration operation) is being performed, the ECM outputs an Eco Driving Indicator Light illumination request signal to the combination meter assembly and illuminates the Eco Driving Indicator Light.

Y101366E01
0.667,1.177 1.146,1.427 0.479,0.25 10 ECM 3.708,1.01 4.146,1.427 0.438,0.417 10 Meter ECU 4.74,1.396 6.375,1.646 1.635,0.25 10 Eco Driving Indicator Light 1.531,1.615 3.229,2.042 1.698,0.427 10 Eco Driving Indicator Light Illumination Request Signal 4.354,2.042 6.271,2.292 1.917,0.25 10 Combination Meter Assembly 1.969,0.896 2.885,1.146 0.917,0.25 10 CAN (V Bus)




FUNCTION


a.

Buzzer Function

i.

The table below shows the functions of the buzzer in the combination meter assembly:

Item

*1: Models with smart entry and start system

*2: Models for G.C.C. countries

*3: Models with 7-speed sport sequential shiftmatic system

·

Front Seat Belt Warning

·

Key Reminder

·

Engine Immobiliser Matching Completion Report

·

Smart Entry and Start System Warning*1

·

Parking Brake On Driving Warning

·

Door Open Driving Warning

·

Speed Warning*2

·

Sport Sequential Shift Reject Warning*3

·

Light Reminder

·

Turn Flasher Sound





b.

Multi-information Display Function

Y132006C02
4.719,1.844 5.052,0.219 5.052,0.219 5.24,0.219 true 0.51,1.031 0.823,1.229 0.313,0.198 10 false *a 0.688,1.427 0.948,1.698 0.26,0.271 10 false A 1.385,1.438 1.646,1.708 0.26,0.271 10 false B 1.156,1.792 1.396,1.979 0.24,0.188 10 false C 5.292,0.104 5.604,0.302 0.313,0.198 10 false *1
*1 Multi-information Display - -
*a Display Area - -


i.

Display Area A (Models with Automatic Transaxle or CVT)

Display Display Item Outline
Y133500

Shift Position Indicator Displays the shift position.


ii.

Display Area B

Display Display Item Outline
Y133501

Clock The clock is always displayed.


iii.

Display Area C

*1: Available only on high grade and sport grade models

*2: Models with automatic transaxle or CVT

Display Display Item Outline
Y132007

Odometer Displays the odometer.
Y132008

Trip Meter Displays the trip meter.
Y132009

Drivable Distance*1
·

Displays the value that has been calculated by the combination meter assembly, which is based on the elapsed time and distance driven after the ignition switch, has been turned to ON.

·

This display is updated every 10 seconds.


Y139097

Average Fuel Consumption Display*1
·

Displays the value that has been calculated by the combination meter assembly, which is based on the distance driven after refueling and the fuel consumption.

·

The combination meter assembly resets the value when determining that the vehicle has been refueled according to the signal from the fuel sender gauge.

·

This display is updated every 10 seconds.


Y132011

Average Vehicle Speed*1
·

Displays a value that has been calculated by the combination meter assembly based on the vehicle speed signal and the elapsed time since the engine start signal.

·

This display is updated every 10 seconds.


Y139098

Instantaneous Fuel Consumption Display*1
·

Displays the value that has been calculated by the combination meter assembly, which is based on the distance driven and the fuel consumption volume.

·

This display is updated constantly.


Y133493

Eco Driving Indicator Light Customizing*2 Displays the customized Eco Driving Indicator Light.




OPERATION


a.

Switching the Multi-information Display

i.

The multi-information display changes in the order shown below by pressing the switch.

Y139099C01
4.354,1.021 4.75,1.25 4.75,1.25 5,1.25 true 5.052,1.146 5.365,1.344 0.313,0.198 10 false *1 1.052,1.573 1.531,1.792 0.479,0.219 10 false *2 (*A) 3.021,1.563 3.5,1.781 0.479,0.219 10 false *3 (*A) 1.073,2.625 1.385,2.823 0.313,0.198 10 false *4 3.063,2.615 3.375,2.813 0.313,0.198 10 false *5 5.031,2.615 5.344,2.813 0.313,0.198 10 false *6 5.031,3.698 5.51,3.917 0.479,0.219 10 false *7 (*B) 5.052,4.781 5.531,5 0.479,0.219 10 false *8 (*B) 3.104,4.781 3.583,5 0.479,0.219 10 false *9 (*B) 1.063,4.781 1.656,5 0.594,0.219 10 false *10 (*B)
*A Models with Automatic Transaxle or CVT *B Available only on high grade and sport grade models
*1 ODO/TRIP DISP Switch *2 Eco Driving Indicator Light Customizing Display: Eco On.
*3 Eco Driving Indicator Light Customizing Display: Eco Off. *4 Odometer Display
*5 Trip Meter A Display *6 Trip Meter B Display
*7 Drivable Distance Display *8 Average Fuel Consumption Display
*9 Instantaneous Fuel Consumption Display *10 Average Vehicle Speed Display
V100135

Pressing the ODO/TRIP DISP switch
V100136

Pressing the ODO/TRIP DISP switch for approximately 5 seconds
·

The set indicator mode will be shown.


V100137

Pressing the ODO/TRIP DISP switch for approximately 2 seconds - -