Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE CONTROL SYSTEM › 2016.04–2017.10
NM30M0E _54 Brake _018312 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0090428 BRAKE CONTROL SYSTEM CO CONTROL F

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE CONTROL SYSTEM  CONTROL  BRAKE CONTROL  


FUNCTION OF MAIN COMPONENTS


Component Function

*1: Models with brake control (ABS with EBD, brake assist, TRC and VSC)

*2: Models with brake control (ABS with EBD)

*3: Models with CVT

Brake Actuator Assembly Skid Control ECU Judges the vehicle driving condition based on the signals from each sensor and switch, and sends the brake control signals to the brake actuator.
Solenoid Valves
·

The hydraulic circuit has 2 master cylinder cut solenoid valves, 4 pressure holding solenoid valves and 4 pressure reduction solenoid valves.*1

·

The hydraulic circuit has 4 pressure holding solenoid valves and 4 pressure reduction solenoid valves.*2

·

Change the fluid path based on the signals from the skid control ECU during the operation of the brake control system functions, in order to control the fluid pressure applied to the wheel cylinders.


Pump Motor Drives the pumps inside the brake actuator.
Solenoid Relay (Built into Skid Control ECU) Supplies power to the solenoid valves.
Motor Relay (Built into Skid Control ECU) Supplies power to the pump motor.
Master Cylinder Pressure Sensor*1 Assembled in the brake actuator, detects the master cylinder pressure.
Spiral Cable with Sensor Sub-assembly*1 Steering Angle Sensor Detects the steering direction and angle of the steering wheel.
Airbag ECU Assembly*1 Yawrate Sensor
·

The airbag ECU assembly incorporates the yawrate sensor and acceleration sensor.

·

The yawrate sensor detects the vehicle's yaw rate.

·

The acceleration sensor detects the vehicle's longitudinal and lateral deceleration.

·

The airbag ECU assembly sends the detection signals from the yawrate sensor and acceleration sensor to the skid control ECU via CAN communication.


Acceleration Sensor
Speed Sensors Detect the wheel speed of each of the 4 wheels.
Deceleration Sensor*2, *3 Detects the angle of inclination of the vehicle.
Stop Light Switch Assembly Detects the brake pedal depressing signal.
Parking Brake Switch Assembly Detects when the parking brake lever is pulled up.
Brake Master Cylinder Sub-assembly Brake Fluid Level Warning Switch Detects the brake fluid level.
VSC OFF Switch*1 Enables the driver to select the "Normal Mode", "TRC OFF Mode", or "VSC OFF Mode".
ECM*1
·

Sends the throttle position signal, accelerator pedal position signal and engine speed signal to the skid control ECU.

·

Based on the signals received from the skid control ECU controls the engine output.


Combination Meter Assembly ABS Warning Light Illuminates to alert the driver when the skid control ECU detects a malfunction in the ABS.
Brake Warning Light
·

Illuminates to alert the driver when the skid control ECU detects a malfunction in the EBD or brake system.

·

Illuminates to alert the driver when the brake fluid level is low.

·

Illuminates to inform the driver when the parking brake is operated.


Slip Indicator Light*1
·

Illuminates to alert the driver if the TRC or VSC system malfunctions.

·

Blinks to inform the driver when the TRC or VSC operates.


TRC OFF Indicator Light*1 Lights up to inform the driver of "TRC OFF mode" or "VSC OFF mode" being selected.
VSC OFF Indicator Light*1 Lights up to inform the driver of "VSC OFF mode" being selected.


SYSTEM CONTROL


a.

Table of System Control

i.

The brake control system has the following system/functions:

Control Outline

*: Models with brake control (ABS with EBD, brake assist, TRC and VSC)

Anti-lock Brake System (ABS) Helps prevent the wheels from locking when the brakes are applied firmly or when braking on a slippery surface.
Electronic Brake Force Distribution (EBD) EBD control utilizes ABS, realizing proper brake force distribution between the front and rear wheels in accordance with the driving conditions. In addition, during braking while cornering, it also controls the brake forces of the right and left wheels, helping maintain vehicle stability.
Electrical Brake Assist* The primary purpose of Brake Assist is to provide supplementary brake force to assist a driver who cannot generate a large brake force during emergency braking, thus helping enhance the vehicle's braking performance.
Traction Control (TRC)* Helps restrain the slippage of the drive wheels if the driver depresses the accelerator pedal excessively when starting off or accelerating on a slippery surface.
Vehicle Stability Control (VSC)* Helps restrain sideways slippage of the vehicle during a strong understeer tendency or strong oversteer tendency while cornering.
Engine Output Control during TRC or VSC Operation* Transmits an engine output control signal from the skid control ECU to the ECM to limit the engine output while the TRC or VSC is being activated.




FAIL-SAFE


a.

If a failure occurs in the skid control ECU, sensors, or brake actuator assembly, the system continues performing brake control by excluding the failed area and using only the areas that are operating normally.



DIAGNOSIS


a.

If the skid control ECU detects a malfunction in the brake control system, the warning lights or indicator light illuminate. At the same time, a Diagnostic Trouble Code (DTC) is stored in the memory of the skid control ECU.


b.

This system has a sensor signal check (test mode) function.


c.

For details of DTCs and check function, refer to the Repair Manual.