Home › Engine / Hybrid System › 2NR-FE ENGINE MECHANICAL › ENGINE UNIT › from 2016.04
NM30M0E _51 Engine / Hybrid System _052896 2NR-FE ENGINE MECHANICAL _0256070 ENGINE UNIT GE GENERAL F

2NR-FE ENGINE MECHANICAL  ENGINE UNIT  GENERAL  GENERAL  


OUTLINE


a.

The 2NR-FE engine is a 1.5-liter, 16-valve DOHC, in-line 4-cylinder engine.


b.

This engine uses a dual Variable Valve Timing-intelligent (VVT-i) system, Direct Ignition System (DIS) and Electronic Throttle Control System-intelligent (ETCS-i). These systems have been developed to achieve high performance and fuel economy, and reduced exhaust emissions.

W129406



SPECIFICATION


Engine Type 2NR-FE
No. of Cyls. and Arrangement 4-cylinder, In-line
Valve Mechanism 16-valve DOHC, Chain Drive (with Dual VVT-i)
Combustion Chamber Pentroof Type
Flow of Intake and Exhaust Gasses Cross-Flow
Fuel System SFI
Ignition System DIS
Displacement 1496 cm3 (91.3 cu. in.)
Bore x Stroke 72.5 mm X 90.6 mm (2.85 in. X 3.57 in.)
Compression Ratio 11.5:1
Max. Output (EEC) 79 kW @ 6000 rpm
Max. Torque (EEC) 140 N*m @ 4200 rpm
Valve Timing Intake Open 10°ATDC to 36°BTDC
Closed 69°ABDC to 23°ABDC
Exhaust Open 48°BBDC to 8°BBDC
Closed 7°ATDC to 47°ATDC
Firing Order 1 - 3 - 4 - 2
Fuel Unleaded Gasoline
Research Octane Number (RON) 91 or higher
Octane Rating 87 or higher
Oil Grade API grade SL "Energy-Conserving", SM "Energy-Conserving", SN "Resource-Conserving" or ILSAC multigrade engine oil
Emission Regulation*1 EURO 2, EURO 4, EURO 5
Engine Service Mass*2 (Reference) M/T 95 kg (209.4 lb.)
CVT 88 kg (194.0 lb.)

HINT:

*1: Emission regulations differ by country and region.

*2: The figure shown is the weight of the engine without coolant and oil.


Performance Curve
W129407E01
5.24,0.656 5.552,0.854 0.313,0.198 10 false 80 5.24,1.031 5.552,1.229 0.313,0.198 10 false 70 5.24,1.427 5.552,1.625 0.313,0.198 10 false 60 5.25,1.833 5.563,2.031 0.313,0.198 10 false 50 5.26,2.229 5.573,2.427 0.313,0.198 10 false 40 5.26,2.625 5.573,2.823 0.313,0.198 10 false 30 5.26,3.021 5.573,3.219 0.313,0.198 10 false 20 5.24,3.427 5.552,3.625 0.313,0.198 10 false 10 5.271,3.833 5.583,4.031 0.313,0.198 10 false 0 4.594,4.177 4.906,4.375 0.313,0.198 10 false 7000 4.188,4.177 4.5,4.375 0.313,0.198 10 false 6000 3.844,4.188 4.156,4.385 0.313,0.198 10 false 5000 3.479,4.188 3.792,4.385 0.313,0.198 10 false 4000 3.104,4.177 3.417,4.375 0.313,0.198 10 false 3000 2.74,4.177 3.052,4.375 0.313,0.198 10 false 2000 2.354,4.188 2.667,4.385 0.313,0.198 10 false 1000 1.708,0.833 2.167,1.031 0.458,0.198 10 false 150 1.708,1.083 2.167,1.281 0.458,0.198 10 false 140 1.708,1.333 2.167,1.531 0.458,0.198 10 false 130 1.708,1.583 2.167,1.781 0.458,0.198 10 false 120 1.708,1.833 2.167,2.031 0.458,0.198 10 false 110 1.708,2.083 2.167,2.281 0.458,0.198 10 false 100 1.792,2.333 2.25,2.531 0.458,0.198 10 false 90 0.688,1.604 1.573,1.969 0.885,0.365 10 false Torque (N*m) 5.667,2.219 6.573,2.552 0.906,0.333 10 false Output (kW) 2.958,4.49 4.25,4.75 1.292,0.26 10 false Engine Speed (rpm)


MAIN FEATURES


a.

The 2NR-FE engine has achieved the following performance through the adoption of the items listed below.

(1) High performance and reliability

(2) Low noise and vibration

(3) Lightweight and compact design

(4) Good serviceability

(5) Clean emission and fuel economy


Section Item (1) (2) (3) (4) (5)
Engine Control System The Electronic Throttle Control System-intelligent (ETCS-i) is used. ○ - - - ○
Magnetic Resistance Element (MRE) type crank position and cam position sensors are used. ○ - - - -
The flat type knock control sensor is used. ○ - - - -
Engine Proper A cylinder head sub-assembly made of aluminum alloy is used. - - ○ - -
A cylinder block sub-assembly made of aluminum alloy is used. - - ○ - -
An offset crankshaft is used. ○ ○ - - ○
Spiny type liners are used. ○ - - - -
Cylinder block water jacket spacer is used. ○ - - - -
A taper squish shape is used for the top of the pistons. ○ - - - ○
The piston skirt is coated with resin. ○ ○ - - ○
An oil pan sub-assembly integrated with oil strainer is used. - - ○ - -
Valve Mechanism The dual Variable Valve Timing-intelligent (VVT-i) system is used. ○ - - - ○
Valve lash adjuster assemblies are used. - ○ - ○ -
No. 1 valve rocker arm sub-assemblies are used. ○ ○ - - ○
Beehive shaped valve spring (outer compression spring) is used. ○ - ○ - -
A timing chain (chain sub-assembly) and No. 1 chain tensioner assembly are used. - ○ - ○ -
Fuel System 8-hole type fuel injector assemblies are used. ○ - - - ○
A fuel returnless system is used. - - ○ ○ -
A multiplex layered plastic fuel tank assembly is used. - - ○ - ○
Quick connectors are used to connect the fuel hoses and fuel pipes. - - - ○ -
Intake and Exhaust System An intake manifold made of plastic is used. - - ○ - -
A linkless type throttle body with motor assembly is used. - - ○ ○ -
A stainless steel exhaust manifold converter sub-assembly is used. - - ○ - ○
Three-Way Catalytic converters (TWCs) are used. - - - - ○
Ignition System A Direct Ignition System (DIS) is used. ○ - - ○ ○
Long-reach, thin-electrode type iridium tipped spark plugs are used. ○ - - ○ ○