Home › Engine / Hybrid System › 2NR-FE ENGINE MECHANICAL › ENGINE UNIT › from 2016.04
NM30M0E _51 Engine / Hybrid System _052896 2NR-FE ENGINE MECHANICAL _0256070 ENGINE UNIT DE DETAILS F

2NR-FE ENGINE MECHANICAL  ENGINE UNIT  DETAILS  CYLINDER BLOCK  


CONSTRUCTION


a.

An aluminum cylinder block sub-assembly with a 7 mm (0.276 in.) distance between the cylinder bores is used to achieve a compact and lightweight configuration.


b.

A spiny type liner, which has an irregularly shaped outer casting surface, is used to enhance the adhesion between the liners and the aluminum of the cylinder block sub-assembly. The enhanced adhesion helps heat dissipation, resulting in a lower overall temperature and reduced heat deformation of the cylinder bores. A cylinder block sub-assembly with this type of liner cannot be rebored.

W113363C01
5.385,1.5 5.542,0.927 5.542,0.927 5.76,0.927 true 5.802,2.25 6.042,2.646 6.042,2.646 6.26,2.646 true 5.823,0.833 6.135,0.99 0.313,0.156 10 false *1 6.333,2.563 6.646,2.719 0.313,0.156 10 false *2 1.604,0.656 1.917,0.813 0.313,0.156 10 false *a 4.531,0.677 4.844,0.833 0.313,0.156 10 false *b
*1 Cylinder Block Sub-assembly *2 Irregularly Shaped Outer Casting Surface of Liner
*a 7 mm (0.276 in.) *b Cylinder Bore Cross Section
V100145

Spiny Type Liner - -



c.

Through the use of an offset crankshaft, the centerline of the cylinder bores is shifted 8 mm (0.315 in.) towards the exhaust in relation to the centerline of the crankshaft. Thus, the side force (thrust) applied to the cylinder walls is reduced when maximum combustion pressure is applied. This contributes to fuel economy.

W100978C02
4.333,2.344 3.719,1.708 3.719,1.708 3.604,1.708 true 1.375,0.781 1.594,0.979 0.219,0.198 10 false *a 1.802,3.375 2,3.573 0.198,0.198 10 false *c 1.865,0.448 2.063,0.635 0.198,0.188 10 false *b 4.406,0.208 4.646,0.406 0.24,0.198 10 false *d 5.74,0.208 5.958,0.417 0.219,0.208 10 false *d 3.458,1.615 3.656,1.802 0.198,0.188 10 false *c 4.385,3.24 4.594,3.438 0.208,0.198 10 false *e 5.896,3.24 6.146,3.458 0.25,0.219 10 false *f
*a 8 mm (0.315 in.) *b Bore Centerline
*c Crankshaft Centerline *d Maximum Pressure
*e Offset Crankshaft *f Non-offset Crankshaft



d.

Water passages are provided between the cylinder bores. By allowing the engine coolant to flow between the cylinder bores, this construction enables the temperature of the cylinder walls to be kept uniform.

W113364C01
4.74,1.448 5.031,0.51 5.031,0.51 5.24,0.51 true 5.135,1.677 5.573,0.531 5.573,0.531 5.792,0.531 true 2.344,1.771 2.656,1.969 0.313,0.198 10 false *a 5.323,0.427 5.635,0.625 0.313,0.198 10 false *a 5.844,0.438 6.156,0.635 0.313,0.198 10 false *a
*a Water Passage - -