Home › Engine / Hybrid System › 1NR-FE ENGINE CONTROL › SFI SYSTEM › 2016.04–2017.10
NM30M0E _51 Engine / Hybrid System _052929 1NR-FE ENGINE CONTROL _0256314 SFI SYSTEM CO CONTROL F

1NR-FE ENGINE CONTROL  SFI SYSTEM  CONTROL  SEQUENTIAL MULTIPORT FUEL INJECTION (SFI) CONTROL  


FUNCTION


a.

EFI-L, which uses an intake mass air flow meter sub-assembly to detect intake air volume and subsequently control fuel injection volume, is used.


b.

Synchronous injection timing (1 injection per cylinder for every 2 crankshaft rotations) is used.


c.

There are 2 fuel injection modes, a synchronous injection and asynchronous injection. In synchronous injection, the basic injection duration is corrected based on signals from each sensor to always inject fuel at the same position. In asynchronous injection, fuel is injected at the point the injection request is detected according to signals from each sensor regardless of the crankshaft angle. In addition, to protect the engine and improve fuel efficiency, a fuel cut that stops fuel injections will be implemented according to the operating conditions.

W129412E02
0.219,0.25 3.021,0.51 2.802,0.26 10 false Intake Mass Air Flow Meter Sub-assembly 0.281,0.948 2.365,1.208 2.083,0.26 10 false Intake Air Temperature Sensor 0.208,1.573 3.417,1.771 3.208,0.198 10 false Crank Position Sensor 0.208,2.115 3.313,2.563 3.104,0.448 10 false Intake Cam Position Sensor (No. 1 Crank Position Sensor) 0.219,3.01 3.438,3.448 3.219,0.438 10 false Exhaust Cam Position Sensor (No. 1 Crank Position Sensor) 0.219,3.906 3.427,4.104 3.208,0.198 10 false Air Fuel Ratio Sensor 0.208,4.438 2.198,4.635 1.99,0.198 10 false Oxygen Sensor 0.208,4.99 5.25,5.188 5.042,0.198 10 false Accelerator Pedal Sensor Assembly 0.219,5.521 2.5,5.75 2.281,0.229 10 false Throttle Position Sensor 0.208,6.073 2.927,6.344 2.719,0.271 10 false E.F.I. Engine Coolant Temperature Sensor 0.208,6.594 2.917,6.833 2.708,0.24 10 false Park/Neutral Position Switch Assembly*1 0.208,7.146 4.333,7.344 4.125,0.198 10 false Power Steering ECU Assembly 0.208,7.677 1.5,7.917 1.292,0.24 10 false Skid Control ECU*2 0.229,8.219 2.667,8.5 2.438,0.281 10 false Air Conditioning Amplifier Assembly*3 4.083,8.177 5.771,8.375 1.688,0.198 10 false CAN (V Bus) 4.615,3.729 5.073,3.927 0.458,0.198 10 false ECM 6.083,3.333 6.885,3.823 0.802,0.49 10 false Fuel Injector Assembly 5.51,7.104 7.01,7.333 1.5,0.229 10 false *1: Models with CVT 5.51,7.458 6.917,7.656 1.406,0.198 10 false *2: Models with ABS 5.51,7.823 6.833,8.302 1.323,0.479 10 false *3: Models with Air Conditioning System


d.

Fuel injection is stopped to protect the engine and improve fuel efficiency.

Fuel Cut

*: Models with CVT

Fuel Cut Off During Deceleration If the engine speed is above a standard value when decelerating (when the ECM determines that the throttle is off), the fuel injection is stopped to prevent overheating of the catalyst by misfiring, and to improve fuel efficiency. If the coolant temperature is low, the fuel cut speed and restoration speed with be increased.
Fuel Cut According to Engine Speed If the engine speed is higher than a standard value, fuel injection is stopped to prevent excessive speed.
Fuel Cut When Shifting from "N" to "D"* If the engine speed is higher than a standard value, fuel injection is stopped when the shift lever is operated to protect the CVT.

Fuel Cut Speed at High Engine Speed
Engine Speed (rpm) 6300