Home › Engine / Hybrid System › 2NZ-FE STARTING › STARTING SYSTEM › 2016.07–2016.10
NM30M0E _51 Engine / Hybrid System _018300 2NZ-FE STARTING _0090377 STARTING SYSTEM CO CONTROL F

2NZ-FE STARTING  STARTING SYSTEM  CONTROL  STARTER CONTROL (CRANKING HOLD FUNCTION)  


SYSTEM CONTROL


a.

Once the engine switch is pushed, this function continues to operate the starter until the engine starts, provided that the brake pedal is depressed and the shift lever is in P or N. This prevents starting failures and the engine from being cranked after the engine has started.


b.

This system cuts off the current that powers the accessories while the engine is cranking to prevent the accessory illumination from operating intermittently due to the unstable voltage that is associated with the cranking of the engine.


c.

When the certification ECU (smart key ECU assembly) detects a start signal from the engine switch, this system monitors the engine speed (NE) signal and continues to operate the starter until it determines that the engine has started. Furthermore, even if the certification ECU (smart key ECU assembly) detects a start signal from the engine switch, this system will not operate the starter if the certification ECU (smart key ECU assembly) has determined that the engine has already started.


d.

After the starter operates and the engine speed becomes higher than approximately 500 rpm, the certification ECU (smart key ECU assembly) determines that the engine has started and stops the output of the STAR signal to the starter relay assembly. Thus, the starter operation stops and the certification ECU (smart key ECU assembly) energizes the ACC relay.


e.

If the engine has any failure and does not start, the starter operates as long as its maximum continuous operation time and stops automatically. The maximum continuous operation time is approximately 5 seconds through 30 seconds depending on the engine water temperature condition. When the engine water temperature is extremely low, it is approximately 30 seconds and when the engine is warmed up sufficiently, it is approximately 5 seconds.

W111960E01
4.406,1.427 3.76,1.427 3.76,1.427 3.76,1.917 false 0.135,0.104 1.271,0.385 1.135,0.281 12 false Timing Chart: 1.792,0.583 2.083,0.823 0.292,0.24 10 false On 0.354,0.646 1.156,0.875 0.802,0.229 10 false Start Signal 1.792,1.094 2.083,1.333 0.292,0.24 10 false Off 1.792,1.927 2.083,2.167 0.292,0.24 10 false On 1.792,2.333 2.083,2.573 0.292,0.24 10 false Off 1.792,2.917 2.083,3.156 0.292,0.24 10 false On 1.792,3.344 2.083,3.583 0.292,0.24 10 false Off 0.396,2.083 1.229,2.542 0.833,0.458 10 false Starter Relay Assembly 0.438,3.083 1.583,3.323 1.146,0.24 10 false Accessory Power 0.406,4.083 2.094,4.354 1.688,0.271 10 false Engine Speed Signal (NE) 4.479,1.354 6.719,1.625 2.24,0.271 10 false Cranking Limit Approx. 5 to 30 sec. 5.594,3.604 6.979,4.031 1.385,0.427 10 false Successful Starting of Engine 5.583,4.313 7.083,4.615 1.5,0.302 10 false Failed Starting of Engine 1.417,4.948 6.302,5.427 4.885,0.479 10 false The certification ECU (smart key ECU assembly) determines that the engine has started successfully when the engine speed is approximately 400 rpm.