OUTLINE
A manual air conditioning system or automatic air conditioning system is used.
SPECIFICATION
Performance
| Item | Specification | ||
|---|---|---|---|
| Heater | Heater Output | W | 4400 |
| Air Flow Volume | m3/h | 280 | |
| Power Consumption | W | 190 | |
| Cooler | Cooling Capacity | W | 4280*1
4770*2 |
| Air Flow Volume | m3/h | 450 | |
| Power Consumption | W | 220 | |
*1: Except models for G.C.C. countries
*2: Models for G.C.C. countries
Ventilation and Heater Radiator Unit Sub-assembly
| Item | Specification | ||
|---|---|---|---|
| Heater Radiator Unit Sub-assembly | Type | Straight Flow Aluminum (SFA)-II | |
| Size (W x H x L) | mm (in.) | 232.7 x 130 x 21 (9.16 x 5.12 x 0.83) | |
| Fin Pitch | mm (in.) | 1.8 (0.07) | |
| Blower Motor with Fan Sub-assembly | Motor Type | K62-10 | |
| Fan Type | Shroud Sirocco | ||
| Fan Size (Dia. x H) | mm (in.) | 110 x 74 (4.33 x 2.91) | |
Air Conditioning
| Item | Specification | ||
|---|---|---|---|
| Cooler Condenser Assembly | Type | Multi-Flow (MF)-IV | |
| Size (W x H x L) | mm (in.) | 520 x 319 x 16 (20.5 x 12.6 x 0.63)*1
600 x 319 x 16 (23.6 x 12.6 x 0.63)*2 |
|
| Fin Pitch | mm (in.) | 2.75 (0.11) | |
| No. 1 Cooler Evaporator Sub-assembly | Type | Beneficial Refrigerant Stream (BRS) | |
| Size (W x H x L) | mm (in.) | 185.9 x 251 x 38 (7.32 x 9.88 x 1.50) | |
| Fin Pitch | mm (in.) | 3.4 (0.13)*3
2.6 (0.10)*4 |
|
| Cooler Compressor Assembly | Type | 10SRE11C | |
| Pulley | Magnetic Clutch | ||
| Refrigerant | Type | HFC 134a | |
| Charge Volume | g | 370 +/- 50*5
400 +/- 50*6 |
|
| Clean Air Filter | Semi Standard Type | ||
*1: Except models with CVT for G.C.C. countries
*2: Models with CVT for G.C.C. countries
*3: Except models for G.C.C. countries
*4: Models for G.C.C. countries
*5: Except models for G.C.C. countries of TMT made
*6: Models for G.C.C. countries of TMT made
MAIN FEATURES
The air conditioning system has the following features:
| High Performance | ·
Neural network control is used so passengers can control the air conditioning accurately for maximum comfort.* ·
The blower control has 7 levels in manual mode and 31 levels in auto mode for more precise control.* |
| Lightweight | A bus connector (air conditioning harness assembly) with a built-in IC is used in a lightweight wire harness design with a reduced number of wires. The use of this connector means that pulse pattern type servo motors are used.* |
| Compact | ·
A semi-center location air conditioning unit in which the cooler evaporator sub-assembly and heater radiator unit sub-assembly are placed in the vehicle's longitudinal direction is used. ·
A blower motor with a built-in blower motor controller is used in a compact construction. |
| Others | The following parts are used to ensure high cooling performance while realizing a compact and lightweight construction.
·
Semi-center location air conditioning unit ·
Beneficial Refrigerant Stream (BRS) evaporator ·
Multi-Flow (MF)-IV sub-cool condenser assembly |
*: Models with automatic air conditioning system