Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM › from 2017.10
NM30M0E _51 Engine / Hybrid System _052536 CRUISE CONTROL _0253678 CRUISE CONTROL SYSTEM CO CONTROL F

CRUISE CONTROL  CRUISE CONTROL SYSTEM  CONTROL  CRUISE CONTROL  


FUNCTION OF MAIN COMPONENTS


a.

The main components in the cruise control system have the following functions:

Component Function

*1: Models with CVT

*2: Models with manual transaxle

*3: Models with shift paddle switch (transmission shift switch assembly)

*4: Models with VSC

*5: Models with color type multi-information display

Accelerator Pedal Sensor Assembly Detects the accelerator pedal depression angle and transmits it to the ECM.
Front Speed Sensor LH/RH, Rear Speed Sensor LH/RH Detects the vehicle speed and transmits a signal via the skid control ECU to the combination meter assembly.
Cruise Control Main Switch ON-OFF Button Turns on/off the power to the cruise control system.
CANCEL Switch A cancel signal can be output to the ECM through the operation of this switch.
RES/+ Switch The acceleration function and resume control function can be performed by operating this switch. A signal is output to the ECM when this switch is operated.
SET/- Switch The deceleration function and set control function can be performed by operating this switch. A signal is output to the ECM when this switch is operated.
Park/Neutral Position Switch Assembly*1 Detects the shift lever position and transmits a signal to the ECM.
Stop Light Switch Assembly Detects the depressing of the brake pedal and transmits a signal to the ECM.
No. 2 Clutch Start Switch Assembly*2 Detects the depressing of the clutch pedal and transmits a signal to the ECM.
Shift Lock Control Unit Assembly*1 Transmission Control Switch
·

Detects the shift lever position and transmits signals to the ECM.

·

Informs the ECM of driver upshift or downshift operations while the shift lever is in M.


Shift Paddle Switch (Transmission Shift Switch Assembly)*3 Informs the ECM of driver upshift or downshift operations.
VSC OFF Switch*4 Detects the VSC off signal and outputs it to the skid control ECU.
ECM
·

Controls the cruise control system in accordance with signals from the switches, sensors and ECUs.

·

If the ECM detects a malfunction in the cruise control system, it will store a Diagnostic Trouble Code (DTC).


Brake Actuator Assembly Skid Control ECU
·

Sends a vehicle speed signal from the speed sensor to the ECM.

·

Transmits the VSC operation signal to the ECM.*4


Combination Meter Assembly Cruise Main Indicator Light
·

Illuminates when the ON-OFF button on the cruise control main switch has been pressed to turn the cruise control system on.

·

If the ECM detects a malfunction, this light illuminates in yellow to warn the driver.


Cruise SET Indicator Light Illuminates when the vehicle speed is set.
Multi-information Display*5 Displays a warning message to alert the driver in accordance with a signal provided by the ECU.
Throttle Body with Motor Assembly Throttle Control Motor Adjusts the throttle valve to the limiter position in accordance with signals from the ECM.
Throttle Position Sensor Transmits the throttle valve position information to the ECM.



FUNCTION


a.

The cruise control system has the following functions:

Function Outline

*1: Models with CVT

*2: Models with shift paddle switch (transmission shift switch assembly)

*3: Models with manual transaxle

*4: Models with VSC

Constant Speed Control The ECM compares the actual vehicle speed and the set speed and if the vehicle speed is lower than the set speed, it uses the throttle control motor to increase the throttle opening.
Set Control When the ON-OFF button is turned on and the cruise control main switch is pressed in the SET/- direction and released, the ECM stores the vehicle speed in the memory and continues to control the vehicle at that speed. The set speed is between approximately 40 km/h (25 mph) or more.
Coast Control When the cruise control main switch is held down in the SET/- direction while the vehicle is running in the cruise control system, the throttle control motor is energized in the throttle closing direction, and the vehicle keeps decelerating. The ECM stores the vehicle speed when the cruise control main switch is released. From then on, the ECM continues to control the vehicle at that speed.
Tap-down Control When the difference between the actual vehicle speed and the set speed is less than 5 km/h (3 mph), the set speed can be lowered in steps of approximately 1.6 km/h (1 mph) by operating the cruise control main switch in the SET/- direction quickly within approximately 0.6 seconds. However, if the difference between the actual vehicle speed and the set speed is greater than 5 km/h (3 mph), the set speed will change to the speed at which the vehicle is being driven at when the switch is pushed.
Accelerator Control When the cruise control main switch is kept pushed to the RES/+ direction while the vehicle is running in the cruise control system, the throttle control motor is energized in the throttle opening direction. The vehicle keeps accelerating and the ECM stores the vehicle speed when the cruise control main switch is released. From then on, the ECM continues to control the vehicle at that speed.
Tap-up Control When the difference between the actual vehicle speed and the set speed is less than 5 km/h (3 mph), the set speed can be increased in steps of approximately 1.6 km/h (1 mph) by operating the cruise control main switch in the RES/+ direction quickly within approximately 0.6 seconds. However, if the difference between the actual vehicle speed and the set speed is greater than 5 km/h (3 mph), the set speed will not change.
Low Speed Limit Control The low speed limit is the lowest speed that the cruise control system can be set to and is set at approximately 40 km/h (25 mph). The cruise control system cannot be set below that speed. If the vehicle speed drops below that speed while running in the cruise control system, the cruise control system is canceled automatically. However the set speed is kept in memory.
Resume Control When the cruise control system has been canceled by something other than the ON-OFF button operation, the mode can be resumed and controlled at the set speed by operating the cruise control main switch in the RES/+ direction when the vehicle speed returns to above the low speed limit (approximately 40 km/h [25 mph]).
Manual Cancel Control If any of the following signals is sent to the ECM while the vehicle is running in the cruise control system, the cruise control system is canceled accordingly.
·

Stop light switch assembly on signal (depress the brake pedal).

·

Signal to move the shift lever from D or M to others.*1

·

When 1st, 2nd or 3rd range is selected in M mode.*1

·

When 1st, 2nd or 3rd range is selected in D by shift paddle switch (transmission shift switch assembly).*2

·

No. 2 clutch start switch assembly on signal (depress the clutch pedal).*3

·

CANCEL switch on signal.

·

ON-OFF button off signal.


Automatic Cancel Control When any of the following conditions occurs during cruise control driving, the set speed in the memory is cleared to cancel the cruise control system.
·

The stop light switch assembly has an open or short circuit.

·

The vehicle speed signal is abnormal.


(Models with Monochrome Type Multi-information Display) Furthermore, the cruise main indicator light illuminates in yellow until the ON-OFF button is turned off, and the operation of the cruise control system is disabled until the ON-OFF button is turned on again.
(Models with Color Type Multi-information Display) Furthermore, the master warning light illuminates, the cruise control indicator light turns off, and a message indicating a malfunction will be displayed on the multi-information display until the cruise control system is turned off using the cruise control main switch. The operation of the cruise control system is disabled until the cruise control system is turned on again using the ON-OFF button.
When the following condition occurs during cruise control driving, the speed that is set in the memory is cleared and the cruise control system is cancelled.
·

ETCS-i has a malfunction.


Furthermore, the operation of the cruise control system will be disabled until the ON-OFF button is turned on again.
When any of the following conditions occurs during the cruise control driving, the set speed in the memory is cleared to cancel the cruise control system.
·

The stop light switch assembly input signal is abnormal.

·

The cancel circuit has a malfunction.


(Models with Monochrome Type Multi-information Display) Furthermore, the cruise main indicator light illuminates in yellow until the ON-OFF button is turned off, and the operation of the cruise control system is disabled until the ignition switch is turned off.
(Models with Color Type Multi-information Display) Furthermore, the master warning light illuminates, the cruise control indicator light turns off, and a message indicating a malfunction will be displayed on the multi-information display until the cruise control system is turned off using the cruise control main switch. The operation of the cruise control system is disabled until the ignition switch is turned off.
When the following condition occurs during cruise control driving, the speed that is set in the memory is cleared and the cruise control system is cancelled.
·

Vehicle speed decreases by 16 km/h (10 mph) or more below the speed at which the cruise control system was set.


When the following condition occurs during cruise control driving, the cruise control system is cancelled.
·

Vehicle speed is below the low speed limit (approximately 40 km/h [25 mph]).


Other Cancellation Conditions If any of the following conditions occurs during cruise control driving, the cruise control system is canceled. However, the set vehicle speed remains in the memory:
·

VSC operates during cruise control driving.*4

·

TRC operates for a certain period of time during cruise control driving.*4

·

TRC is off or VSC is off.*4





DIAGNOSIS


a.

Models with Monochrome Type Multi-information Display

i.

If a malfunction occurs in the cruise control system, the ECM cancels the cruise control system. The ECM illuminates the cruise main indicator light in yellow to inform the driver of a malfunction. At this time, the ECM memorizes the malfunction in the form of a 5-digit Diagnostic Trouble Code (DTC). For details of the DTC, refer to the Repair Manual.



b.

Models with Color Type Multi-information Display

i.

If a malfunction occurs in the cruise control system during cruise control operation, the ECM cancels cruise control operation, illuminates the master warning light and turns off the cruise control indicator light and cruise SET indicator light. At this time, "Cruise Control Malfunction Visit Your Dealer" is displayed on the multi-information display. The ECM stores the malfunction in the form of a 5-digit Diagnostic Trouble Code (DTC). For details, refer to the Repair Manual.