OPERATION
ABS with EBD
Based on the signals received from the 4 speed sensors, the skid control ECU calculates each wheel speed and deceleration, and checks wheel slipping conditions. According to the slipping condition, the skid control ECU controls the pressure holding valve and pressure reduction valve in order to adjust the fluid pressure of each wheel cylinder in the following 3 modes: pressure reduction, pressure holding and pressure increase modes.
| *1 | Port A | *2 | Port B |
| *3 | Pressure Holding Valve | *4 | Pressure Reduction Valve |
| *a | Increase Mode | *b | Holding Mode |
| *c | Reduction Mode | *d | to Wheel Cylinder |
| *e | to Reservoir and Pump | *f | from Wheel Cylinder |
| Not Activated | Normal Braking | - | - |
|---|---|---|---|
| Activated | Increase Mode | Holding Mode | Reduction Mode |
| Pressure Holding Valve (Port A) | OFF (Open) | ON (Close) | ON (Close) |
| Pressure Reduction Valve (Port B) | OFF (Close) | OFF (Close) | ON (Open) |
| Wheel Cylinder Pressure | Increased | Held | Reduced |
Brake Assist (Electrical Type Brake Assist)
In the event of emergency braking, the skid control ECU determines the driver's intentions based on the speed of the pressure increase in the master cylinder detected by the master cylinder pressure sensor signal. If the skid control ECU judges the need for additional brake assist, pressure to supplement the amount provided by the master cylinder is generated by the pump in the brake actuator and directed to each wheel cylinder.
| *1 | Brake Actuator Assembly | *2 | Master Cylinder Pressure Sensor |
| *3 | Port (A) | *4 | Port (B) |
| *5 | Port (C) | *6 | Port (D) |
| *7 | Port (E) | *8 | Port (F) |
| *9 | Port (G) | *10 | Port (H) |
| *11 | Port (I) | *12 | Port (J) |
| *13 | Pump | *14 | Reservoir |
| *15 | Front Wheel Cylinder RH | *16 | Rear Wheel Cylinder LH |
| *17 | Rear Wheel Cylinder RH | *18 | Front Wheel Cylinder LH |
| *a | Brake Assist Operation | *b | From Master Cylinder |
Each valve operates as shown below:
| Item | Port | Not Activated | Activated | |
|---|---|---|---|---|
| Master Cylinder Cut Solenoid Valve | (1) | (A) | OFF (Open) | ON* |
| (2) | (B) | OFF (Open) | ON* | |
| Pressure Holding Solenoid Valve | (3) | (C) | OFF (Open) | OFF (Open) |
| (4) | (D) | OFF (Open) | OFF (Open) | |
| (5) | (E) | OFF (Open) | OFF (Open) | |
| (6) | (F) | OFF (Open) | OFF (Open) | |
| Pressure Reduction Solenoid Valve | (7) | (G) | OFF (Closed) | OFF (Closed) |
| (8) | (H) | OFF (Closed) | OFF (Closed) | |
| (9) | (I) | OFF (Closed) | OFF (Closed) | |
| (10) | (J) | OFF (Closed) | OFF (Closed) | |
| Pump | OFF | ON | ||
*: Hydraulic pressure is controlled by continuously cycling the solenoid valves between open and closed, according to the operating conditions.
TRC
The fluid pressure generated by the pump is regulated by the master cylinder cut solenoid valve to the required pressure. Thus, the wheel cylinders of the drive wheels are controlled in the following 3 modes: pressure reduction, pressure holding, and pressure increase modes to control the slippage of the drive wheels. The diagram below shows the hydraulic circuit in pressure increase mode when the TRC is activated. Each pressure holding solenoid valve and the pressure reduction solenoid valve is turned on/off according to the ABS with EBD operation pattern.
| *1 | Brake Actuator Assembly | *2 | Master Cylinder Pressure Sensor |
| *3 | Port (A) | *4 | Port (B) |
| *5 | Port (C) | *6 | Port (D) |
| *7 | Port (E) | *8 | Port (F) |
| *9 | Port (G) | *10 | Port (H) |
| *11 | Port (I) | *12 | Port (J) |
| *13 | Pump | *14 | Reservoir |
| *15 | Front Wheel Cylinder RH | *16 | Rear Wheel Cylinder LH |
| *17 | Rear Wheel Cylinder RH | *18 | Front Wheel Cylinder LH |
| *a | TRC Operation | *b | From Master Cylinder |
| Item | Port | Not Activated | Activated | ||||
|---|---|---|---|---|---|---|---|
| Increase Mode | Holding Mode | Reduction Mode | |||||
| Master Cylinder Cut Solenoid Valve | (1) | (A) | OFF (Open) | ON* | ON* | ON* | |
| (2) | (B) | OFF (Open) | ON* | ON* | ON* | ||
| Front Brake | Pressure Holding Solenoid Valve | (3) | (C) | OFF (Open) | OFF (Open) | OFF (Open) | ON (Closed) |
| (6) | (F) | OFF (Open) | OFF (Open) | OFF (Open) | ON (Closed) | ||
| Pressure Reduction Solenoid Valve | (7) | (G) | OFF (Closed) | OFF (Closed) | OFF (Closed) | ON (Open) | |
| (10) | (J) | OFF (Closed) | OFF (Closed) | OFF (Closed) | ON (Open) | ||
| Brake Wheel Cylinder Pressure | Right | - | - | Increase | Hold | Reduce | |
| Left | - | - | Increase | Hold | Reduce | ||
| Rear Brake | Pressure Holding Solenoid Valve | (4) | (D) | OFF (Open) | ON (Closed) | ON (Closed) | ON (Closed) |
| (5) | (E) | OFF (Open) | ON (Closed) | ON (Closed) | ON (Closed) | ||
| Pressure Reduction Solenoid Valve | (8) | (H) | OFF (Closed) | OFF (Closed) | OFF (Closed) | OFF (Closed) | |
| (9) | (I) | OFF (Closed) | OFF (Closed) | OFF (Closed) | OFF (Closed) | ||
| Brake Wheel Cylinder Pressure | Right | - | - | - | - | - | |
| Left | - | - | - | - | - | ||
| Pump | OFF | ON | ON | ON | |||
*: Hydraulic pressure is controlled by continuously cycling the solenoid valves between open and closed, according to the operating conditions.
VSC
The VSC, by the way of solenoid valves, controls the fluid pressure that is generated by the pump and applies it to the brake wheel cylinder of each wheel in the following 3 modes: pressure reduction, pressure holding, and pressure increase modes. As a result, the tendency of front wheel skid or rear wheel skid is controlled.
In front wheel skid restraining control, the brakes of the front and rear wheels of the inner circle of the turn are applied. Also, depending on whether the brake is on or off and the condition of the vehicle, there are circumstances in which the brake might not be applied to the wheels even if the wheel is targeted for braking. The diagram below shows the hydraulic circuit in pressure increase mode, as it controls a front wheel skid condition while the vehicle is making a right turn. In other operating modes, each pressure holding valve and pressure reduction valve is turned on/off according to the ABS with EBD operation pattern.
| *1 | Brake Actuator Assembly | *2 | Master Cylinder Pressure Sensor |
| *3 | Port (A) | *4 | Port (B) |
| *5 | Port (C) | *6 | Port (D) |
| *7 | Port (E) | *8 | Port (F) |
| *9 | Port (G) | *10 | Port (H) |
| *11 | Port (I) | *12 | Port (J) |
| *13 | Pump | *14 | Reservoir |
| *15 | Front Wheel Cylinder RH | *16 | Rear Wheel Cylinder LH |
| *17 | Rear Wheel Cylinder RH | *18 | Front Wheel Cylinder LH |
| *a | VSC Operation (Front Wheel Skid Restraining Control) | *b | From Master Cylinder |
| Item | Port | Not Activated | Activated | ||||
|---|---|---|---|---|---|---|---|
| Increase Mode | Holding Mode | Reduction Mode | |||||
| Master Cylinder Cut Solenoid Valve | (1) | (A) | OFF (Open) | ON* | ON* | ON* | |
| (2) | (B) | OFF (Open) | ON* | ON* | ON* | ||
| Front Brake | Pressure Holding Solenoid Valve | (3) | (C) | OFF (Open) | OFF (Open) | ON (Closed) | ON (Closed) |
| (6) | (F) | OFF (Open) | OFF (Open) | ON (Closed) | ON (Closed) | ||
| Pressure Reduction Solenoid Valve | (7) | (G) | OFF (Closed) | OFF (Closed) | OFF (Closed) | ON (Open) | |
| (10) | (J) | OFF (Closed) | OFF (Closed) | OFF (Closed) | ON (Open) | ||
| Brake Wheel Cylinder Pressure | Right | - | - | Increase | Hold | Reduce | |
| Left | - | - | Increase | Hold | Reduce | ||
| Rear Brake | Pressure Holding Solenoid Valve | (4) | (D) | OFF (Open) | ON (Closed) | ON (Closed) | ON (Closed) |
| (5) | (E) | OFF (Open) | OFF (Open) | ON (Closed) | ON (Closed) | ||
| Pressure Reduction Solenoid Valve | (8) | (H) | OFF (Closed) | OFF (Closed) | OFF (Closed) | OFF (Closed) | |
| (9) | (I) | OFF (Closed) | OFF (Closed) | OFF (Closed) | ON (Open) | ||
| Brake Wheel Cylinder Pressure | Right | - | - | Increase | Hold | Reduce | |
| Left | - | - | - | - | - | ||
| Pump | OFF | ON | ON | ON | |||
*: Hydraulic pressure is controlled by continuously cycling the solenoid valves between open and closed, according to the operating conditions.
In rear wheel skid restraining control, the brakes of the front wheels on the outer circle of the turn are applied. Also, depending on whether the brake is on or off and the condition of the vehicle, there are circumstances in which the brake might not be applied to the wheels even if the wheel is targeted for braking. The diagram below shows the hydraulic circuit in the pressure increase mode, as it controls a rear wheel skid condition while the vehicle is making a right turn. In other operating modes, each pressure holding valve and pressure reduction valve is turned on/off according to the ABS with EBD operation patterns.
| *1 | Brake Actuator Assembly | *2 | Master Cylinder Pressure Sensor |
| *3 | Port (A) | *4 | Port (B) |
| *5 | Port (C) | *6 | Port (D) |
| *7 | Port (E) | *8 | Port (F) |
| *9 | Port (G) | *10 | Port (H) |
| *11 | Port (I) | *12 | Port (J) |
| *13 | Pump | *14 | Reservoir |
| *15 | Front Wheel Cylinder RH | *16 | Rear Wheel Cylinder LH |
| *17 | Rear Wheel Cylinder RH | *18 | Front Wheel Cylinder LH |
| *a | VSC Operation (Rear Wheel Skid Restraining Control) | *b | From Master Cylinder |
| Item | Port | Not Activated | Activated | ||||
|---|---|---|---|---|---|---|---|
| Increase Mode | Holding Mode | Reduction Mode | |||||
| Master Cylinder Cut Solenoid Valve | (1) | (A) | OFF (Open) | ON* | ON* | ON* | |
| (2) | (B) | OFF (Open) | ON* | ON* | ON* | ||
| Front Brake | Pressure Holding Solenoid Valve | (3) | (C) | OFF (Open) | ON (Closed) | ON (Closed) | ON (Closed) |
| (6) | (F) | OFF (Open) | OFF (Open) | ON (Closed) | ON (Closed) | ||
| Pressure Reduction Solenoid Valve | (7) | (G) | OFF (Closed) | OFF (Closed) | OFF (Closed) | OFF (Closed) | |
| (10) | (J) | OFF (Closed) | OFF (Closed) | OFF (Closed) | ON (Open) | ||
| Brake Wheel Cylinder Pressure | Right | - | - | - | - | - | |
| Left | - | - | Increase | Hold | Reduce | ||
| Rear Brake | Pressure Holding Solenoid Valve | (4) | (D) | OFF (Open) | OFF (Open) | ON (Closed) | ON (Closed) |
| (5) | (E) | OFF (Open) | ON (Closed) | ON (Closed) | ON (Closed) | ||
| Pressure Reduction Solenoid Valve | (8) | (H) | OFF (Closed) | OFF (Closed) | OFF (Closed) | ON (Open) | |
| (9) | (I) | OFF (Closed) | OFF (Closed) | OFF (Closed) | OFF (Closed) | ||
| Brake Wheel Cylinder Pressure | Right | - | - | - | - | - | |
| Left | - | - | Increase | Hold | Reduce | ||
| Pump | OFF | ON | ON | ON | |||
*: Hydraulic pressure is controlled by continuously cycling the solenoid valves between open and closed, according to the operating conditions.
Hill-start Assist Control
Hill-start Assist Control controls the brakes by maintaining the master cylinder fluid pressure produced by depressing the brake pedal.
| *1 | Brake Actuator Assembly | *2 | Master Cylinder Pressure Sensor |
| *3 | Port (A) | *4 | Port (B) |
| *5 | Port (C) | *6 | Port (D) |
| *7 | Port (E) | *8 | Port (F) |
| *9 | Port (G) | *10 | Port (H) |
| *11 | Port (I) | *12 | Port (J) |
| *13 | Pump | *14 | Reservoir |
| *15 | Front Wheel Cylinder RH | *16 | Rear Wheel Cylinder LH |
| *17 | Rear Wheel Cylinder RH | *18 | Front Wheel Cylinder LH |
| *a | Hill-start Assist Control Operation | *b | From Master Cylinder |
| Item | Port | Hill-start Assist Control Activated | ||||
|---|---|---|---|---|---|---|
| Not Activated | Pressure Holding Mode | Pressure Reduction Mode | ||||
| Master Cylinder Cut Solenoid Valve | (1) | (A) | OFF (Open) | ON* | ON* | |
| (2) | (B) | OFF (Open) | ON* | ON* | ||
| Front Brake | Pressure Holding Solenoid Valve | (3) | (C) | OFF (Open) | OFF (Open) | OFF (Open) |
| (6) | (F) | OFF (Open) | OFF (Open) | OFF (Open) | ||
| Pressure Reduction Solenoid Valve | (7) | (G) | OFF (Closed) | OFF (Closed) | OFF (Closed) | |
| (10) | (J) | OFF (Closed) | OFF (Closed) | OFF (Closed) | ||
| Brake Wheel Cylinder Pressure | Right | - | - | Hold | Reduce | |
| Left | - | - | Hold | Reduce | ||
| Rear Brake | Pressure Holding Solenoid Valve | (4) | (D) | OFF (Open) | OFF (Open) | OFF (Open) |
| (5) | (E) | OFF (Open) | OFF (Open) | OFF (Open) | ||
| Pressure Reduction Solenoid Valve | (8) | (H) | OFF (Closed) | OFF (Closed) | OFF (Closed) | |
| (9) | (I) | OFF (Closed) | OFF (Closed) | OFF (Closed) | ||
| Brake Wheel Cylinder Pressure | Right | - | - | Hold | Reduce | |
| Left | - | - | Hold | Reduce | ||
| Pump | OFF | OFF | OFF | |||
*: Hydraulic pressure is controlled by continuously cycling the solenoid valves between open and closed, according to the operating conditions.
Engine Output Control during TRC or VSC Operation
During the TRC or VSC operation, the skid control ECU outputs the engine output control signal to the ECM. Upon receiving this signal, the ECM inhibits the engine output.