Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM › 2017.10–2018.01
NM30M0E _55 Steering _018317 POWER ASSIST SYSTEMS _0090433 POWER STEERING SYSTEM CO CONTROL F

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  CONTROL  POWER STEERING CONTROL  


FUNCTION OF MAIN COMPONENTS


Component Function

*1: TMMIN made models

*2: TMT made models

*3: Models with color type multi-information display

Steering Column Assembly Power Steering Motor Generates power assist in accordance with a signal received from the power steering ECU assembly.
Reduction Mechanism Reduces the speed of the power steering motor through the use of a worm gear and a wheel gear and transmits it to the column shaft.
Torque Sensor Detects the amount of twist of the torsion bar. Based on the torque applied to the torsion bar, the sensor creates an electrical signal, and outputs this signal to the power steering ECU assembly.
Combination Meter Assembly Power Steering Warning Light (Red)*1 Lights up to alert the driver when the power steering ECU assembly detects a malfunction in the EPS system.
Power Steering Warning Light (Red/Yellow)*2
·

Illuminates in red to alert the driver when the power steering ECU assembly detects a malfunction in the EPS system which results in a loss of steering assist torque.

·

Illuminates in yellow to alert the driver when the power steering ECU assembly detects a malfunction in the EPS system which limits the steering assist torque.


Speedometer Outputs the vehicle speed signal to the power steering ECU assembly.*1
Multi-information Display*3 Displays the warning message to inform the driver of a malfunction in the EPS system.
Buzzer Sounds to alert the driver when the power steering ECU assembly detects a malfunction in the EPS system.*2
Power Steering ECU Assembly
·

Actuates the power steering motor mounted on the steering column assembly to provide power assist, based on the signals received from various sensors and ECUs.

·

Outputs idle up request signals to the ECM.


Brake Actuator Assembly Skid Control ECU Outputs the vehicle speed signal to the power steering ECU assembly.*2
ECM Outputs the engine speed signal to the power steering ECU assembly.


SYSTEM CONTROL


a.

On TMMIN made models, the power steering ECU assembly calculates the steering assist force based on steering torque information from the torque sensor, vehicle speed information from the speedometer and information from each ECU and controls the power steering motor to generate the required steering assist torque.


b.

On TMT made models, the power steering ECU assembly calculates the steering assist force based on steering torque information from the torque sensor, vehicle speed information from the skid control ECU and information from each ECU and controls the power steering motor to generate the required steering assist torque.


c.

The EPS system consists of the control function listed below:

Control Outline
Steering Assist Control Basic Control Calculates the assist current required based on the steering torque value and the vehicle speed and actuates the power steering motor.
Compensation Control Compensates with a force, according to the driver's steering maneuver, improving the comfort of steering.



FAIL-SAFE


a.

TMMIN Made Models

i.

If the power steering ECU assembly detects a malfunction in the EPS system, the power steering ECU assembly illuminates the power steering warning light (red) to alert the driver of the malfunction.


ii.

If a system malfunction occurs, the power steering ECU assembly changes control mode to fail-safe mode. For details, refer to the Repair Manual.



b.

TMT Made Models

i.

If the power steering ECU assembly detects a malfunction in the EPS system, the power steering ECU assembly illuminates the power steering warning light (red*1 and yellow*2) and master warning light*3, and displays the warning message on the multi-information display*3, and sounds the buzzer to alert the driver of the malfunction.

HINT:

*1: Illuminates when a malfunction which results in a loss of steering assist torque occurs.

*2: Illuminates when a malfunction which limits the steering assist torque occurs.

*3: Models with color type multi-information display



ii.

If a system malfunction occurs, the power steering ECU assembly changes control mode to fail-safe mode. For details, refer to the Repair Manual.




DIAGNOSIS


a.

If the power steering ECU assembly detects a malfunction in the EPS system, the power steering ECU assembly lights up the power steering warning light in order to alert the driver. At the same time, Diagnostic Trouble Codes (DTCs) are stored in memory.


b.

The DTCs can be read by connecting the Global TechStream (GTS) to the DLC3. For details, refer to the Repair Manual.