Home › Drivetrain › K312 CVT › CVT SYSTEM › from 2017.10
NM30M0E _52 Drivetrain _052301 K312 CVT _0252107 CVT SYSTEM CO CONTROL F

K312 CVT  CVT SYSTEM  CONTROL  CVT CONTROL  


FUNCTION OF MAIN COMPONENTS


a.

The main components of the K312 Continuously Variable Transaxle (CVT) are as follows:

Component Function

*1: Models with air conditioning system

*2: Models with shift paddle switch

Continuously Variable Transaxle Assembly On-off Solenoid Valve SC (for Clutch) Used to switch control of the linear solenoid valve SLU for forward and reverse clutch control.
On-off Solenoid Valve SL (for Lock-up) Used to switch control of the linear solenoid valve SLU for lock-up clutch control.
Linear Solenoid Valve SLU (for Lock-up Control) Performs forward and reverse clutch control or lock-up clutch control depending on the state of the on-off solenoid valves SC and SL.
Linear Solenoid Valve SLP (for Primary Pulley Control) Controls the oil pressure of the primary pulley in accordance with the vehicle speed and accelerator pedal position signals to control the speed ratio.
Linear Solenoid Valve SLS (for Secondary Pulley Control) Controls the oil pressure of the secondary pulley in accordance with the input shaft torque to control belt clamping force.
Transmission Revolution Sensor (NIN) Detects the primary pulley speed (input speed).
Transmission Revolution Sensor (NOUT) Detects the secondary pulley speed (output speed).
Transmission Revolution Sensor (NT) Detects the turbine speed of the torque converter.
CVT Fluid Temperature Sensor Detects the CVT fluid temperature.
Oil Pressure Sensor Detects the steel belt clamping force.
E.F.I. Engine Coolant Temperature Sensor Detects the engine coolant temperature.
Throttle Body with Motor Assembly Throttle Position Sensor Detects the opening angle of the throttle valve.
Airbag ECU Assembly Yawrate Sensor Detects the vehicle's yaw rate.
Acceleration Sensor Detects the vehicle's longitudinal and lateral acceleration and deceleration.
Stop Light Switch Assembly Detects the brake pedal depressing signal.
Park/Neutral Position Switch Assembly Detects the shift lever position.
Shift Lock Control Unit Assembly Transmission Control Switch
·

Detects that the shift lever is in M.

·

Detects the driver's shift-up and shift-down operations when the shift lever is in M.


Shift Paddle Switch (Transmission Shift Switch Assembly)*2
·

Detects the driver's shift-up and shift-down operations in 7-speed sport sequential shiftmatic mode.

·

Operating this switch when the shift lever is in D changes the mode temporarily to 7-speed sport sequential shiftmatic mode.


Crank Position Sensor Detects the engine speed.
Accelerator Pedal Sensor Detects the accelerator pedal opening angle.
Air Conditioning Amplifier Assembly*1 Transmits the operating state of the air conditioning system to the ECM.
ECM Drives each solenoid valve based on signals from each sensor and switch and optimally controls the CVT.
Combination Meter Assembly Shift Position and Shift Range Indicator
·

Indicates the shift lever position.

·

Indicates the shift range.


Malfunction Indicator Lamp (MIL) Illuminates or blinks to inform the driver when the ECM detects a malfunction.



SYSTEM CONTROL


a.

Control List

i.

The electronic control system of the K312 CVT consists of the controls listed below.

Control Outline
Engine-CVT Integrated Control Effects coordinated control of the CVT system and engine control system to ensure both smooth and powerful driving that excels in shift response and fuel economy.
Automatic Shift Control (Speed Ratio Control) Controls the primary pulley speed to approach the calculated target input rotation speed based on information such as the accelerator pedal position, vehicle speed and stop light switch signals.
Acceleration Improvement Control Controls the acceleration rate in proportion to the accelerator pedal position, improving the feeling of linear acceleration and expanding the feeling of accelerator pedal input.
Deceleration Improvement Control Determines a pulley ratio which allows for high engine speed to be maintained during deceleration, thus ensuring adequate engine braking.
Uphill/Downhill Shift Control Uses the ECM to determine whether the vehicle is traveling uphill or downhill in order to restrict upshifts or provide appropriate engine braking force by restricting downshifts.
Lock-up Control By enhancing the lock-up operation range into the low vehicle speed range, the fuel cut range has been enlarged, achieving improved fuel economy.
Flex Lock-up Control
7-speed Sport Sequential Shiftmatic Enables driving in a gear step selected using the shift lever, providing engine braking force appropriate to each gear step.



b.

Engine - CVT Integrated Control

i.

To effect fine-tuned control in accordance with driving conditions, various signals are exchanged between the engine control system and the CVT system. As a result, both smooth and powerful driving that excels in shift response and fuel economy has been achieved.

X109756E08
1.76,0.438 2.302,0.646 0.542,0.208 10 false Engine 4.938,1.167 5.479,1.375 0.542,0.208 10 false CVT 4.656,0.083 6.167,0.469 1.51,0.385 10 false Transmission Revolution Sensor (NIN) Signal 5.281,2.063 6.208,2.417 0.927,0.354 10 false Fluid Pressure Control Circuit 4.031,3.125 5.188,3.49 1.156,0.365 10 false Calculation of CVT Control Amount 1.979,3.125 3.302,3.469 1.323,0.344 10 false Calculation of Engine Control Amount 1.99,4.052 3.26,4.417 1.271,0.365 10 false Calculation of Target Torque 1.979,5 3.26,5.365 1.281,0.365 10 false Calculation of Target Engine Output 4.146,4.979 5.021,5.323 0.875,0.344 10 false Calculation of Target Speed 4.281,5.667 5.052,5.865 0.771,0.198 10 false CVT Control 2.219,5.667 3.156,5.865 0.938,0.198 10 false Engine Control 1.26,6.479 2.781,6.781 1.521,0.302 10 false Vehicle Speed Signal 2.74,6.479 5.25,6.75 2.51,0.271 10 false Accelerator Pedal Position Signal 0.802,2.906 1.344,3.115 0.542,0.208 10 false ECM



c.

Automatic Shift Control (Speed Ratio Control)

i.

The ECM determines the driving conditions through each input signal and selects the optimal control to achieve output which meets the driver's intentions.


ii.

The ECM calculates the target primary pulley speed in accordance with the accelerator pedal position signal, vehicle speed signal, and stop light switch signal, in order to attain an optimal pulley ratio and shifting speed. To adjust the actual primary pulley speed (acquired from the primary speed sensor) to match the target primary pulley speed, the ECM actuates linear solenoid valves SLP and SLS in order to control the pressure of primary pulley and secondary pulley. As a result, the optimal pulley ratio and shifting speed are achieved.

X109757E03
0.75,0.375 2.323,0.573 1.573,0.198 10 false Vehicle Speed Signal 0.563,0.698 2.365,0.875 1.802,0.177 10 false Stop Light Switch Signal 0.99,1.021 2.125,1.625 1.135,0.604 10 false Accelerator Pedal Position Signal 0.594,1.917 2.094,2.594 1.5,0.677 10 false Transmission Revolution Sensor (NIN) Signal 2.677,0.438 3.635,1.167 0.958,0.729 10 false Target Primary Pulley Speed 2.667,1.635 3.635,2.281 0.969,0.646 10 false Actual Primary Pulley Speed 4.281,0.813 5.167,1.802 0.885,0.99 10 false Calculation of Control Amount 5.813,0.906 6.792,1.365 0.979,0.458 10 false Linear Solenoid Valve SLP 5.802,1.719 6.771,2.25 0.969,0.531 10 false Linear Solenoid Valve SLS


iii.

When the shift lever is in D, the system effects engine integrated control to optimize fuel economy characteristics and driving performance.

X114042E01
4.875,0.667 6.333,1.198 1.458,0.531 10 false : Control Area 2.448,0.302 3.833,0.979 1.385,0.677 10 false Pulley Ratio (Low) 0.906,1.281 2.344,2.063 1.438,0.781 10 false Primary Pulley Speed 2.74,2.156 4.24,2.563 1.5,0.406 10 false Vehicle Speed 4.25,1.333 5.813,1.896 1.563,0.563 10 false Pulley Ratio (High)


iv.

When the shift lever is in M, the shift characteristic is as shown below. The system will upshift automatically when the vehicle reaches the set speed during acceleration.

X100456E12
2.938,1.083 3.156,1.323 0.219,0.24 10 1st 3.406,1.073 3.677,1.323 0.271,0.25 10 2nd 3.813,1.135 4.208,1.417 0.396,0.281 10 3rd 4.333,1.125 4.771,1.406 0.438,0.281 10 4th 4.906,1.146 5.292,1.427 0.385,0.281 10 5th 5.469,1.25 5.792,1.531 0.323,0.281 10 6th 5.458,1.688 5.844,1.969 0.385,0.281 10 7th 0.604,2.052 2.385,2.49 1.781,0.438 10 Primary Pulley Speed 3.615,3.875 5.438,4.313 1.823,0.438 10 Vehicle Speed 2.188,0.594 3.76,0.906 1.573,0.313 10 Pulley Ratio (Low) 5.125,2.448 6.698,2.813 1.573,0.365 10 Pulley Ratio (High)



d.

Acceleration Improvement Control

i.

The system determines the driver's acceleration request based on the vehicle speed and changes in the accelerator pedal position. When the system determines this request, it will change the shift characteristics to ones in which the engine speed and vehicle speed increase linearly, providing improved acceleration feeling.

X104368E04
2.625,4.354 2.344,4.354 2.344,4.354 2.594,3.729 true 2.792,2.802 2.51,2.802 2.51,2.802 2.677,2.302 true 3.417,1.323 3.135,1.323 3.135,1.323 3.333,1.823 true 1.271,3.396 2.271,3.906 1,0.51 10 false Acceleration 1.198,1.896 2.448,2.323 1.25,0.427 10 false Engine Speed 5.24,0.948 5.906,1.281 0.667,0.333 10 false Time 0.938,0.51 2.073,1.188 1.135,0.677 10 false Accelerator Pedal Position 5.25,2.438 5.917,2.771 0.667,0.333 10 false Time 5.208,3.865 5.875,4.198 0.667,0.333 10 false Time 3.49,1.25 6.896,1.646 3.406,0.396 10 false Increases Linearly in Accordance with Vehicle Speed 2.875,2.719 7.052,3.115 4.177,0.396 10 false Suppresses Engine Speed Increase at Beginning of Acceleration 2.698,4.271 6.917,4.667 4.219,0.396 10 false Linearly Increases Acceleration Immediately Following Acceleration



e.

Deceleration Improvement Control

i.

During deceleration, a pulley ratio which allows high engine speed to be maintained, is calculated, thus providing adequate engine braking.


ii.

During subsequent acceleration, the engine is controlled to generate driving force quickly.

X104369E03
3.073,0.396 2.802,0.396 2.802,0.396 2.802,1.021 false 4.469,1.49 5.396,1.49 false 0.458,2.865 1.604,3.635 1.146,0.771 10 false Accelerator Pedal Operation 0.875,1.281 2.021,1.677 1.146,0.396 10 false Engine Speed 1.625,2.76 1.99,3.156 0.365,0.396 10 false On 1.625,3.281 1.99,3.677 0.365,0.396 10 false Off 4.76,3.438 5.323,3.781 0.563,0.344 10 false Time 4.781,2.313 5.333,2.708 0.552,0.396 10 false Time 3.135,0.323 5.563,1.094 2.427,0.771 10 false Ensures Engine Braking by Maintaining High Engine Speed 5.469,1.396 7.01,2.25 1.542,0.854 10 false Improves Re-acceleration Response through Quick Engine Speed Increase



f.

Uphill/Downhill Shift Control

i.

Uphill/downhill shift control helps perform optimal shifting while driving on a winding uphill or downhill road.


ii.

When the ECM determines the vehicle is traveling uphill, the control restricts upshifting, thus offering smooth driving.


iii.

If a signal indicating that the driver has operated the brake pedal is input when the ECM has determined the vehicle is traveling downhill, the control downshifts to generate optimal engine braking force.

X101083E01
0.552,2.469 1.594,2.719 1.042,0.25 10 without Control 4.552,3.333 5.625,3.542 1.073,0.208 10 Brake Operation 0.74,3.052 1.583,3.271 0.844,0.219 10 with Control 2.094,2.188 2.781,2.396 0.688,0.208 10 Downshift 3.448,2.188 4.135,2.396 0.688,0.208 10 Downshift 5.083,2.802 5.771,3.01 0.688,0.208 10 Downshift 2.854,2.188 3.375,2.396 0.521,0.208 10 Upshift 4.333,2.188 4.854,2.396 0.521,0.208 10 Upshift 4.333,2.802 4.854,3.01 0.521,0.208 10 Upshift 2.542,2.802 3.656,3.01 1.115,0.208 10 Restricts Upshift


iv.

The actual acceleration calculated from the vehicle speed signal is compared with the reference acceleration (based on level road travel) stored in the ECM to determine uphill or downhill travel.

X109760C02
1.219,0.521 1.01,0.521 1.01,0.521 0.75,0.99 true 5.125,0.813 4.917,0.813 4.917,0.813 4.656,1.292 true 1.26,0.458 1.552,0.656 0.292,0.198 10 *c 5.156,0.729 5.448,0.927 0.292,0.198 10 *d 0.271,0.271 0.563,0.469 0.292,0.198 10 *a 3.865,0.292 4.156,0.49 0.292,0.198 10 *b
*a Uphill *b Downhill
*c Smaller *d Greater
V100135

Reference Acceleration
V100136

Actual Acceleration




g.

Lock-up Control

i.

The lock-up operation range has been expanded from that of previous continuously variable transaxles, thus enabling control to start from low speeds.


ii.

The lock-up operation range during deceleration has been expanded to the low-speed range. This expands the fuel cut range and achieves excellent fuel economy.

X109761E02
0.854,0.927 2.302,1.198 1.448,0.271 10 false Throttle Opening Angle 3.542,2.271 4.49,2.458 0.948,0.188 10 false Vehicle Speed 3.5,1.375 4.479,1.625 0.979,0.25 10 false Lock-up On 2.458,0.375 3.229,0.594 0.771,0.219 10 false Lock-up Off



h.

Flex Lock-up Control

i.

In order to improve the transmission efficiency and also the fuel economy, the linear solenoid valve SLU for lock-up engagement pressure control is employed to deliver flex lock-up control that can provide more precise control than that of a conventional lock-up clutch mechanism.


ii.

Flex lock-up control during deceleration is used to expand the fuel-cut range. It operates the lock-up clutch over the low vehicle speed range when the vehicle decelerates so that minimal speed difference between the engine speed and turbine speed can be maintained.



i.

7-speed Sport Sequential Shiftmatic

i.

The driver can select the desired gear step by moving the shift lever to "+" (forward) or to "-"(backward) while the shift lever is in M (7-speed sport sequential shiftmatic mode). Thus, the driver is able to change gear steps with a manual-like feel.


ii.

A shift paddle switch (transmission shift switch assembly), which enables the driver to perform shift operations while holding the steering wheel, is provided depending on the model.


iii.

7-speed sport sequential shiftmatic mode can be selected from normal driving mode by moving the shift lever to M. The driver can change the gear step by selecting it using the shift lever or shift paddle switch (transmission shift switch assembly)*1 and engine braking force is provided in accordance with the selected gear step.*2

*1: Models with shift paddle switch

*2: On models with the shift paddle switch, if the shift paddle switch (transmission shift switch assembly) "+ (UP)" or "- (DOWN)" is operated during normal driving mode with the shift lever in D, gear step change operations are temporarily made available.


iv.

Through the engine-CVT integrated control, pulley ratio and engine torque which corresponds to shifting speed are finely controlled, thus improving shifting response and achieving a reduction in shifting shock.

X115190E13
1.365,0.698 1.823,0.896 0.458,0.198 10 false ECM 5.385,0.125 6.771,0.823 1.385,0.698 10 false Shift Lock Control Unit Assembly 5.438,0.969 6.74,1.51 1.302,0.542 10 false Transmission Control Switch 4.073,2.281 5.281,3.302 1.208,1.021 10 false Shift Paddle Switch (Transmission Shift Switch Assembly)* 2.594,1.958 3.5,2.49 0.906,0.531 10 false Fluid Pressure Control 1.583,1.969 2.344,2.521 0.76,0.552 10 false Pulley Ratio Control 0.146,1.969 0.646,2.281 0.5,0.313 10 false ETCS-i 0.906,1.979 1.406,2.292 0.5,0.313 10 false ESA 2.063,3.854 3.438,4.052 1.375,0.198 10 false Transaxle 0.615,3.542 1.531,3.74 0.917,0.198 10 false Engine 2.917,0.313 4.906,0.51 1.99,0.198 10 false M Position Signal 2.917,0.792 6.125,0.99 3.208,0.198 10 false Shift Range Up Signal 2.906,1.302 6.427,1.5 3.521,0.198 10 false Shift Range Down Signal 0.073,4.458 5.198,4.74 5.125,0.281 10 false *: Models with Shift Paddle Switch


v.

The shift position and shift range indicator is provided in the combination meter assembly. When the shift lever is in P, R, N or D, the shift position is indicated on the shift position and shift range indicator. When the shift lever is in M, or temporary 7-speed sport sequential shiftmatic mode is selected with the shift lever in D,* "M" or "D" and the selected shift range is displayed on the shift position and shift range indicator.

*: Models with shift paddle switch

Models with Monochrome Type Multi-information Display
X137903C02
0.75,0.417 3.583,1.25 2.833,0.833 4.25,0.417 5.167,1.25 0.917,0.833 5.5,0.417 6.417,1.25 0.917,0.833 0.813,0.448 1.125,0.646 0.313,0.198 10 false *a 0.156,1.5 0.469,1.698 0.313,0.198 10 false *d 4.302,0.448 4.615,0.646 0.313,0.198 10 false *b 5.552,0.438 6.052,0.635 0.5,0.198 10 false *c (*A)
*A Models with Shift Paddle Switch - -
*a When shift lever is in P, R, N or D *b When shift lever is in M
*c During temporary 7-speed sport sequential shiftmatic mode with shift lever in D *d This illustration is an example only.


Models with Color Type Multi-information Display
X137897C01
0.76,0.333 4.083,0.333 false 0.75,1.417 4.083,1.417 false 4.583,0.333 6.5,0.333 false 4.583,1.417 6.5,1.417 false 4.583,1.417 4.583,0.333 false 6.5,1.417 6.5,0.333 false 4.083,1.417 4.083,0.333 false 0.75,1.417 0.75,0.333 false 0.854,0.417 1.167,0.573 0.313,0.156 10 false *a 4.688,0.417 5,0.573 0.313,0.156 10 false *b 0.167,1.5 0.479,1.656 0.313,0.156 10 false *c
*a When shift lever is in P, R, N or D *b When shift lever is in M
*c This illustration is an example only. - -



vi.

In 7-speed sport sequential shiftmatic mode, the transmission automatically upshifts or downshifts under the following conditions:

Condition System Control
Engine is under-revving. 1 step downshift
Engine is over-revving. 1 step upshift


vii.

When the vehicle is stopped during 7-speed sport sequential shiftmatic mode, the transmission automatically downshifts to M1.


viii.

The ECM will restrict the changing of the gear step if it detects a malfunction in the CVT system.


ix.

If the vehicle speed and engine speed exceeds or goes below a preset level in response to the driver's downshift operation request, changing the gear step will be prohibited. In this case, the buzzer in the combination meter will sound to alert the driver.




FAIL-SAFE


a.

This function helps reduce the loss of operability when a malfunction occurs in any sensor or shift solenoid valve.


b.

For details, refer to the Repair Manual.



DIAGNOSIS


a.

When the ECM detects a malfunction, it records the malfunction and information related to the fault. Furthermore, the ECM will illuminate or blink the MIL in the combination meter to inform the driver.


b.

At the same time, the Diagnostic Trouble Codes (DTCs) are stored in memory. The DTCs can be read by connecting the Global TechStream (GTS) to the DLC3. For details, refer to the Repair Manual.