Home › Engine / Hybrid System › 2NR-FE ENGINE CONTROL › SFI SYSTEM › from 2017.10
NM30M0E _51 Engine / Hybrid System _052894 2NR-FE ENGINE CONTROL _0256063 SFI SYSTEM CO CONTROL F

2NR-FE ENGINE CONTROL  SFI SYSTEM  CONTROL  ENGINE CONTROL  


FUNCTION OF MAIN COMPONENTS


a.

The main components of the 2NR-FE engine control system are as follows.

Components Outline Quantity Function
ECM 32-bit CPU 1 The ECM optimally controls the SFI, ESA and ETCS-i to suit the operating conditions of the engine in accordance with the signals provided by the sensors.
Crank Position Sensor (Rotor Teeth) Magnetic Resistance Element (MRE) Type (36-2) 1 This sensor detects the engine speed and performs cylinder identification.
Cam Position Sensor (No. 1 Crank Position Sensor) (Rotor Teeth) Magnetic Resistance Element (MRE) Type (3) 2 This sensor performs cylinder identification.
Knock Control Sensor Built-in Piezoelectric Element Type (Flat Type) 1 This sensor detects an occurrence of the engine knocking indirectly from the vibration of the cylinder block caused by the occurrence of engine knocking.
Intake Mass Air Flow Meter Sub-assembly Hot-wire Type 1 This sensor uses a built-in hot-wire to directly detect the intake air mass.
Throttle Position Sensor Non-contact Type 1 This sensor detects the throttle valve opening angle.
Oxygen Sensor Cup Type with Heater 1 This sensor detects the oxygen concentration in the exhaust emission by measuring the electromotive force which is generated in the sensor itself.
Air Fuel Ratio Sensor Planar Type with Heater 1 As with the oxygen sensor, this sensor detects the oxygen concentration in the exhaust gas. However, it detects the oxygen concentration in the exhaust gas linearly.
Accelerator Pedal Sensor Assembly Non-contact Type 1 This sensor detects the amount of pedal effort applied to the accelerator pedal.
Fuel Injector Assembly 8-hole Type 4 The fuel injector is an electromagnetically-operated solenoid with a nozzle which injects fuel in accordance with signals from the ECM.
E.F.I. Engine Coolant Temperature Sensor Thermistor Type 1 This sensor detects the water temperature by means of an internal thermistor.



SYSTEM CONTROL


a.

The engine control system of the 2NR-FE engine has the following systems.

System Function

*1: Models with CVT

*2: Models with smart entry and start system

*3: Models with air conditioning system

Sequential Multiport Fuel Injection (SFI) An L-type SFI system is used, the intake air mass is detected with a hot-wire type air flow meter. The fuel injection system is a sequential multiport fuel injection system.
Electronic Spark Advance (ESA) The ECM determines the optimal ignition timing in accordance with the signals received from the sensors and sends (IGt) ignition signal to the igniter. The ECM corrects ignition timing in response to engine knocking.
Electronic Throttle Control System-intelligent (ETCS-i) Optimally controls the throttle valve opening in accordance with the amount of accelerator pedal effort, the throttle valve opening control request from the ECM, and the condition of the engine and the vehicle.
Dual Variable Valve Timing-intelligent (VVT-i) Regulates operation of the intake and exhaust camshafts to ensure optimal valve timing in accordance with engine operating conditions.
Cooling Fan Control Cooling fan operation is controlled by signals from the ECM based on the E.F.I. engine coolant temperature sensor signal.
Fuel Pump Control Fuel pump operation is controlled by signals from the ECM. The fuel pump is stopped when the SRS airbags deploy.
Evaporative Emission Control The ECM controls the purge flow of evaporative emissions (HC) from the charcoal canister in accordance with engine conditions.
Brake Booster Vacuum Ejector Control*1 The ECM controls the No. 2 vacuum switching valve assembly to compensate for the reduction in negative pressure of the brake booster assembly.
Starter Control (Cranking Hold Function)*2 Once the engine switch is pushed, this control continues to operate the starter until the engine is started.
Air Conditioning Cut-off Control*3
·

By turning the air conditioning compressor on or off in accordance with engine operating conditions, drivability is maintained.

·

By using the pressure inside the brake booster and the atmospheric pressure to calculate the negative pressure inside the brake booster, the compressor assembly operation stop time is optimized and the engine load is reduced, reducing the pressure inside the intake manifold and maintaining the negative pressure of the brake booster.


Air Fuel Ratio Sensor and Oxygen Sensor Heater Control Maintains the temperature of the air fuel ratio sensor and oxygen sensor at an appropriate level to increase the detection accuracy of the exhaust gas oxygen concentration.
Engine Immobiliser Prohibits fuel delivery and ignition if an attempt is made to start the engine with an invalid ignition key.
Brake Override System The driving torque is restricted when both the accelerator and brake pedals are depressed. (For the Activation Conditions and Inspection Method, refer to the repair manual)



FAIL-SAFE


a.

When the ECM detects a malfunction, the ECM stops or controls the engine according to the data already stored in the memory. For details, refer to the Repair Manual.



DIAGNOSIS


a.

When the ECM detects a malfunction, the ECM diagnoses and memorizes the failed section. For details, refer to the Repair Manual.