CONSTRUCTION
A sound insulation material is used in the body frame profile, thus reducing the various noises which intrude from the outside of the vehicle to the inside of the cabin.
| *a | A-A Cross Section | *b | B-B Cross Section |
| *c | C-C Cross Section | *d | D-D Cross Section |
| *e | E-E Cross Section | *f | F-F Cross Section |
| *g | G-G Cross Section | *h | H-H Cross Section |
| *i | I-I Cross Section | *j | J-J Cross Section |
|
Polyurethane Foam |
|
Expanded Foam |
| *a | A-A Cross Section | *b | B-B Cross Section |
| *c | C-C Cross Section | *d | D-D Cross Section |
| *e | E-E Cross Section | *f | F-F Cross Section |
| *g | G-G Cross Section | *h | H-H Cross Section |
| *i | I-I Cross Section | *j | J-J Cross Section |
|
Polyurethane Foam |
|
Expanded Foam |
| *a | A-A Cross Section | *b | B-B Cross Section |
| *c | C-C Cross Section | *d | D-D Cross Section |
| *e | E-E Cross Section | *f | F-F Cross Section |
| *g | G-G Cross Section | *h | H-H Cross Section |
| *i | I-I Cross Section | *j | J-J Cross Section |
|
Polyurethane Foam |
|
Expanded Foam |
A material having high sound-shielding property is used for the intermediate film of the laminated glass of the windshield to reduce wind noise.
A hood insulator is fitted to the underneath the engine hood, so that an air layer is provided between the hood panel and the insulator, forming a dual-layer structure, thus enhancing the noise shielding performance.
The front fender side panel protector is used in the front fenders to block noise and air flow from between the fender and the front pillar to the doors, thus reducing noise from the wheel house and engine room.
A fender liner silencer is provided. These reduce the amount of engine noise leaking into and out of the cabin.
A urethane radiator grille seal and front side air guide is used in the front fender to reduce the noise which travels through the fender toward the cabin.
| *1 | Radiator Grille Seal | *2 | Front Side Air Guide |
| *3 | Hood Panel | *4 | Hood Insulator |
| *5 | Front Fender Sub-assembly | *6 | Front Fender Liner |
| *7 | Fender Liner Silencer | *8 | Front Fender Side Panel Protector |
| *9 | Front Door Panel | *10 | Side Panel Outer |
| *11 | Glass | *12 | Intermediate Film |
| *a | A-A Cross Section | *b | B-B Cross Section |
| *c | C-C Cross Section | *d | D-D Cross Section |
| *e | E-E Cross Section | *f | Air Layer |
For the dash panel insulator, a rubber layer has been added between the felt layers, as well as increasing the thickness of the felt material, so that the sound insulation and sound absorption performances will increase.
For the outer dash panel insulator, the amount of fiberglass has been optimized to enhance the sound absorption capability, improving the sound insulation.
| *1 | Outer Dash Panel Insulator | *2 | Dash Panel |
| *3 | Dash Panel Insulator Assembly | *4 | Non Woven Fabric |
| *5 | Fiberglass | *6 | Rubber Layer |
| *7 | Felt (Sound Absorption) | - | - |
| *a | Cross Section | *b | Engine Compartment Side |
| *c | Interior Side | - | - |
| *1 | Outer Dash Panel Insulator | *2 | Dash Panel |
| *3 | Dash Panel Insulator Assembly | *4 | Non Woven Fabric |
| *5 | Fiberglass | *6 | Rubber Layer |
| *7 | Felt (Sound Absorption) | - | - |
| *a | Cross Section | *b | Engine Compartment Side |
| *c | Interior Side | - | - |
To reduce the amount of road noise, engine noise and droning sound that enters the cabin, vibration damping sheet is applied to the floor panel.
| *A | For Sedan Models | *B | For Hatchback Models |
|
Sheet Type Damping Material Application Area | - | - |
|
Sheet Type Damping Material Application Area | - | - |