Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM › from 2018.01
NM30M0E _58 Vehicle Interior _018322 THEFT DETERRENT / KEYLESS ENTRY _0092837 SMART ENTRY AND START SYSTEM CO CONTROL F

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM  CONTROL  SMART ENTRY AND START CONTROL  


FUNCTION OF MAIN COMPONENTS


a.

The main components of the entry function have the following functions:

Component Function

*1: for sedan

*2: for hatchback

*3: Models with color type multi-information display

*4: Models with monochrome type multi-information display

Electrical Key Transmitter Sub-assembly
·

When receiving the request signals that are output by the No. 1 indoor electrical key antenna assembly (instrument panel), door electrical key antenna (front door outside handle assembly driver side), No. 2 indoor electrical key antenna assembly (rear floor), electrical key antenna (outside luggage compartment) the key outputs information such as the key ID and vehicle ID.

·

When a driver pushes the lock/unlock button or luggage compartment door opener button*1 on the key, the key outputs a request signal.

·

When receiving the radio wave that is output by the transponder key amplifier in the engine switch, the key outputs information such as the key ID and vehicle ID.

·

Integrates with the mechanical key in order to unlock the doors when the key battery is low.


Certification ECU (Smart Key ECU Assembly)
·

Judges and certifies the key.

·

Controls the No. 1 Indoor electrical key antenna assembly (instrument panel), door electrical key antenna (front door outside handle assembly driver side), No. 2 indoor electrical key antenna assembly (rear floor), and electrical key antenna (outside luggage compartment).

·

Transmits door lock/unlock request signals during the entry function.

·

Transmits steering lock/unlock request signals.

·

Transmits engine immobiliser set/unset request signals.

·

Records the ID codes between the steering lock ECU (steering lock actuator assembly).


Body Computer
·

Receives the request signal from the certification ECU (smart key ECU assembly) and actuates the door lock motors to unlock or lock all the doors, and the luggage compartment door*1.

·

Transmits the condition of each door to the certification ECU (smart key ECU assembly).


Door Outside Handle Assembly Lock/Unlock Switch Transmits the door lock/unlock request signal to the certification ECU (smart key ECU assembly).
Door Electrical Key Antenna Receives a request signal from the certification ECU (smart key ECU assembly), and creates an actuation area around the front door of driver side.
Luggage Electrical Key Switch*1 Transmits a luggage door open request signal to the certification ECU (smart key ECU assembly).
Back Door Opener Switch Assembly*2 Back Door Opener Switch Transmits a back door open request signal to the certification ECU (smart key ECU assembly).
Back Door Lock Switch Transmits a door lock request signal to the certification ECU(smart key ECU assembly).
Door Lock Assembly Door Lock Motor Drives the motor in response to signals from the body computer and locks or unlocks the doors.
Door Lock Position Switch (Front Driver Side) Detects whether the door is locked or unlocked and sends this information to the body computer.
Door Lock Position Switch (Front Passenger Side, Rear RH, Rear LH) Detects whether the door is locked or unlocked and sends this information to the certification ECU (smart key ECU assembly).
Luggage Compartment Door Lock Assembly*1 Door Lock Motor Drives the motor in response to signals from the body computer and releases the luggage compartment door latch.
Courtesy Light Switch Detects whether the luggage compartment door is open or closed and sends this information to the body computer.
Back Door Lock Assembly*2 Door Lock Motor Drives the motor in response to signals from the body computer and releases the back door latch.
Courtesy Light Switch Detects whether the back door is open or closed and sends this information to the body computer.
Electrical Key Antenna (Outside Luggage Compartment) Receives a request signal from the certification ECU (smart key ECU assembly), and forms an actuation area around the rear bumper.
Door Control Receiver Receives the ID code from the key in the actuation area and transmits it to the certification ECU (smart key ECU assembly).
Door Courtesy Light Switch Assembly Detects whether the doors are open or closed and sends this information to the body computer.
Wireless Door Lock Buzzer Sounds to inform the driver of malfunctions in the smart entry and start system.
Combination Meter Assembly Buzzer Sounds to inform the driver of malfunctions in the smart entry and start system.
Multi-information Display*3 Informs the driver of power source or system abnormalities by displaying a warning message.
Smart Warning Light*4 Illuminates to inform the driver of power source or system abnormalities.


b.

The main components of the start function have the following functions:

Component Function

*1: Models with CVT

*2: Models with manual transaxle

*3: Models with color type multi-information display

*4: Models with monochrome type multi-information display

Engine Switch
·

Transmits the engine switch signal to the certification ECU (smart key ECU assembly).

·

Receives the ID code and transmits it to the certification ECU (smart key ECU assembly) when the key battery is low.


Electrical Key Transmitter Sub-assembly Receives signals from the antennas and returns the ID code to the door control receiver.
No. 1 Indoor Electrical Key Antenna Assembly (Instrument Panel) Receives a request signal from the certification ECU (smart key ECU assembly) and forms an actuation area in the vehicle.
No. 2 Indoor Electrical Key Antenna Assembly (Rear Floor)
Door Control Receiver Receives the ID code from the key and transmits it to the certification ECU (smart key ECU assembly).
Certification ECU (Smart Key ECU Assembly)
·

Certifies the ID code received from the door control receiver and transmits the certification results to the steering lock ECU.

·

Outputs steering lock ECU (steering lock actuator assembly) lock/unlock command signals.


Stop Light Switch Assembly*1 Outputs the state of the brake pedal to the certification ECU (smart key ECU assembly).
Clutch Start Switch Assembly*2 Outputs the state of the clutch pedal to the certification ECU (smart key ECU assembly).
ECM Receives the signal from certification ECU (smart key ECU assembly) and performs engine ignition.
Steering Lock ECU (Steering Lock Actuator Assembly)
·

Receives the command signal from the certification ECU (smart key ECU assembly) and activates the steering lock actuator.

·

Registers the ID verification code.


Combination Meter Assembly Buzzer Sounds to inform the driver of malfunctions in the smart entry and start system.
Multi-information Display*3 Informs the driver of power source or system abnormalities by displaying a warning message.
Smart Warning Light*4 Illuminates to inform the driver of power source or system abnormalities.
Shift Lock Control ECU*1 Outputs the shift position P detection switch signal to the certification ECU (smart key ECU assembly).



OPERATING CONDITION


a.

The smart entry and start system is activated only when the key is within the actuation area formed by the 4 antennas located within the vehicle.


b.

Each antenna attempts to detect whether the key is within the actuation area and responds with the following actions.

Y217251C01
3.594,1.375 3.917,0.417 3.917,0.417 4.083,0.417 true 4.708,2.333 5.167,3.25 5.167,3.25 5.333,3.25 true 2.458,2.333 2.083,3.25 2.083,3.25 1.917,3.25 true 3.552,3.729 2.25,4.667 2.25,4.667 2.083,4.667 true 3.531,4.563 2.5,5.333 2.5,5.333 2.333,5.333 true 1.469,3.125 1.969,3.292 0.5,0.167 10 false *1 (*A) 1.906,4.531 2.167,4.729 0.26,0.198 10 false *2 2.146,5.219 2.375,5.385 0.229,0.167 10 false *3 5.375,3.125 5.823,3.302 0.448,0.177 10 false *4 (*B) 4.135,0.313 4.385,0.458 0.25,0.146 10 false *5 2.073,1.906 2.333,2.083 0.26,0.177 10 false *a 4.875,1.906 5.135,2.083 0.26,0.177 10 false *a 3.458,4.896 3.719,5.073 0.26,0.177 10 false *a
*A LHD Models *B RHD Models
*1 Front Door Outside Handle Assembly LH
·

Door Electrical Key Antenna


*2 No. 2 Indoor Electrical Key Antenna Assembly (Rear Floor)
*3 Electrical Key Antenna (Outside Luggage Compartment) *4 Front Door Outside Handle Assembly RH
·

Door Electrical Key Antenna


*5 No. 1 Indoor Electrical Key Antenna Assembly (Instrument Panel) - -
*a Approximately 0.7 to 1.0 m (27.6 to 39.4 in.) - -
V100144

Interior Actuation Area
V100145

Exterior Actuation Area


Each Actuation Area
Actuation Area Details

*1: Models with CVT

*2: Models with manual transaxle

*3: for sedan

*4: for hatchback

Interior This actuation area becomes active and the system will attempt to detect the key when any one of the following situations occurs:
·

Driver door is opened or closed

·

Engine switch is pressed while the brake pedal*1 or clutch pedal*2 is depressed

·

Warning for the smart entry and start system occurs

·

Lock/unlock switch is pressed


Exterior Around Front Door The range of the actuation area is approximately 0.7 to 1.0 m (27.6 to 39.4 in.) radius of the outside handle of the driver door. When the lock/unlock switch provided on the driver door outside handle is pressed, the actuation area becomes active and the system will attempt to detect key.
Around Luggage Compartment Door*3 The range of the actuation area is approximately 0.7 to 1.0 m (27.6 to 39.4 in.) radius of the center of the luggage compartment door. When the luggage electrical key switch is pressed, the actuation area becomes active and the system will attempt to detect key.
Around Back Door*4 The range of the actuation area is approximately 0.7 to 1.0 m (27.6 to 39.4 in.) radius of the center of the back door. When the back door opener switch or back door lock switch is pressed, the actuation area becomes active and the system will attempt to detect key.



FUNCTION


a.

Start Function

i.

The start function has different power source patterns to suit the brake pedal state and shift lever position. (Models with CVT)

Pattern Brake Pedal Shift Lever Power Source Pattern
A Depressed P or N Position When the engine switch is pushed once.
·

OFF→IG-ON (after the engine is started)


B Not Depressed P Position Each time the engine switch is pushed.
·

OFF→ACC→IG-ON→ACC


C Except P Position Each time the engine switch is pushed.
·

OFF→ACC→IG-ON→ACC


D - P Position When the engine switch is pushed in the IG-ON condition.
·

IG-ON (engine is started or not started)→OFF


E - Except P Position When the engine switch is pushed in the IG-ON condition.
·

IG-ON (engine is started or not started)→ACC



Transition of Power Source Mode
Y131891E10
0.208,0.688 0.719,1.083 0.51,0.396 10 false Shift Position 4.531,0.688 5.042,1.083 0.51,0.396 10 false N 2.167,0.708 2.677,1.104 0.51,0.396 10 false P 5.74,0.698 6.802,1.073 1.063,0.375 10 false Except P and N 0.229,1.365 0.771,1.698 0.542,0.333 10 false Pattern 1.063,1.365 1.604,1.698 0.542,0.333 10 false B or D 1.938,1.365 2.479,1.698 0.542,0.333 10 false A or D 4,1.375 4.542,1.708 0.542,0.333 10 false C or E 4.802,1.375 5.344,1.708 0.542,0.333 10 false A or E 5.594,1.365 6.135,1.698 0.542,0.333 10 false C or E 0.229,1.781 0.688,2.208 0.458,0.427 10 false Engine Switch 1.031,1.771 1.521,2.177 0.49,0.406 10 false Pushed 1.854,1.792 2.344,2.198 0.49,0.406 10 false Pushed 3.948,1.781 4.438,2.188 0.49,0.406 10 false Pushed 4.75,1.771 5.24,2.177 0.49,0.406 10 false Pushed 5.563,1.781 6.052,2.188 0.49,0.406 10 false Pushed 6.354,1.792 6.844,2.198 0.49,0.406 10 false Pushed 6.292,2.5 6.979,2.885 0.688,0.385 10 false Depressed 4.688,2.469 5.375,2.854 0.688,0.385 10 false Depressed 5.49,2.479 6.167,2.927 0.677,0.448 10 false Not Depressed 2.625,3.167 3.135,3.677 0.51,0.51 10 false After 20 Minutes 0.917,2.469 1.594,2.917 0.677,0.448 10 false Not Depressed 1.76,2.479 2.448,2.865 0.688,0.385 10 false Depressed 0.26,2.49 0.667,2.927 0.406,0.438 10 false Brake Pedal 0.302,3.24 0.708,3.677 0.406,0.438 10 false Time 3.865,2.458 4.542,2.906 0.677,0.448 10 false Not Depressed 3.292,3.167 3.719,3.677 0.427,0.51 10 false After 1 Hour 0.188,3.896 0.854,4.208 0.667,0.313 10 false Off (Lock) 0.188,4.26 0.823,4.594 0.635,0.333 10 false On (ACC) 0.25,4.667 0.792,4.99 0.542,0.323 10 false On (IG) 0.281,5.063 0.76,5.375 0.479,0.313 10 false Start 4.083,4.229 4.344,4.479 0.26,0.25 10 false "A" 4.354,4.229 4.615,4.479 0.26,0.25 10 false "A" 5.188,4.25 5.448,4.5 0.26,0.25 10 false "A" 5.677,4.24 5.938,4.49 0.26,0.25 10 false "A" 5.927,4.25 6.188,4.5 0.26,0.25 10 false "A" 6.76,4.24 7.021,4.49 0.26,0.25 10 false "A" 0.76,5.573 1.74,5.823 0.979,0.25 10 false : Transition 0.781,5.917 3.25,6.177 2.469,0.26 10 false : Only when the key has been certified 0.76,6.26 3.229,6.521 2.469,0.26 10 false : Only when the vehicle is stopped 0.74,6.563 6.813,7.083 6.073,0.521 10 false - When vehicle is running, if the engine switch is pressed for 2 seconds or more, or briefly 3 times or more in succession, then the engine is stopped, and the engine switch will be turned on (ACC). 0.719,7.24 6.99,7.625 6.271,0.385 10 false : Power transition is available only when the shift lever is moved to P after "A" has come into effect.

NOTICE:
·

Normally, the operation of the engine switch is disabled while the vehicle is being driven. However, if the engine must be stopped in an emergency while the vehicle is in motion, the driver can press the engine switch for approximately 2 seconds or more, or press it briefly for 3 times or more in succession to stop the engine.

·

If no signals are transmitted to the certification ECU (smart key ECU assembly) due to a malfunction in the stop light switch assembly or park/neutral position switch assembly, the engine will not start even if the driver presses the engine switch while depressing the brake pedal. In this case, the driver can start the engine by the following operations. Press the engine switch to turn the power source mode from off (Lock) to on (ACC), and press the engine switch again and hold it for 15 seconds or more.

·

The above 2 operations must be applied only in emergency situations. Under normal conditions, the engine must not be stopped by pressing the engine switch during driving or started without depressing the brake pedal when the shift lever is in any position other than P or N.




ii.

The start function has different power source patterns to suit the clutch pedal (Models with Manual Transaxle).

Pattern Clutch Pedal Power Source Pattern
A Depressed When the engine switch is pushed once.
·

OFF →IG-ON (after the engine is started)


B Not Depressed Each time the engine switch is pushed.
·

OFF →ACC →IG-ON →OFF



Transition of Power Source Mode
Y137935E13
1.74,0.854 2.219,1.052 0.479,0.198 10 false Pattern 1.5,1.26 2.417,1.458 0.917,0.198 10 false Engine Switch 1.74,1.667 2.208,1.833 0.469,0.167 10 false Clutch 1.781,2.188 2.115,2.375 0.333,0.188 10 false Time 1.01,3.333 1.896,3.521 0.885,0.188 10 false Power Source 2.281,2.688 2.594,2.885 0.313,0.198 10 false OFF 2.24,3.115 2.635,3.323 0.396,0.208 10 false (ACC) 2.208,3.51 2.677,3.729 0.469,0.219 10 false On (IG) 2.052,3.896 2.854,4.104 0.802,0.208 10 false Engine Start 3.448,0.833 3.594,1.021 0.146,0.188 10 false B 4.573,0.833 4.719,1.021 0.146,0.188 10 false A 5.719,0.885 5.865,1.073 0.146,0.188 10 false - 5.719,1.292 5.865,1.479 0.146,0.188 10 false - 5.719,1.677 5.865,1.865 0.146,0.188 10 false - 3.229,1.219 3.74,1.406 0.51,0.188 10 false Pushed 4.385,1.24 4.896,1.427 0.51,0.188 10 false Pushed 4.292,1.656 4.979,1.833 0.688,0.177 10 false Depressed 3.469,1.677 3.615,1.865 0.146,0.188 10 false - 3.458,2.219 3.604,2.406 0.146,0.188 10 false - 4.573,2.219 4.719,2.406 0.146,0.188 10 false - 5.198,2.021 5.698,2.375 0.5,0.354 10 false After 20 Minutes 5.802,2.021 6.24,2.375 0.438,0.354 10 false After 1 Hour 0.688,4.521 1.406,4.708 0.719,0.188 10 false : Transition 0.688,4.906 3.073,5.083 2.385,0.177 10 false : Only when the key certification is OK. 0.688,5.292 2.833,5.521 2.146,0.229 10 false : Only when the vehicle is stopped.

NOTICE:
·

Normally, the operation of the engine switch is disabled while the vehicle is being driven. However, if the engine must be stopped in an emergency while the vehicle is in motion, the driver can press the engine switch for approximately 2 seconds or more, or press it briefly for 3 times or more in succession to stop the engine.

·

If no signals are transmitted to the certification ECU (smart key ECU assembly) due to a malfunction in the clutch start switch assembly, the engine will not start even if the driver presses the engine switch while depressing the clutch pedal. In this case, the driver can start the engine by the following operations. Press the engine switch to turn the power source mode from off (Lock) to on (ACC), and press the engine switch again and hold it for 15 seconds or more.

·

The above 2 operations must be applied only in emergency situations. Under normal conditions, the engine must not be stopped by pressing the engine switch while driving or started without depressing the clutch pedal.






SYSTEM CONTROL


a.

Entry Function

i.

The entry function consists of the following functions:

Function Outline

*1: for sedan

*2: for hatchback

*3: Models with color type multi-information display

*4: Models with monochrome type multi-information display

Wireless Door Lock Control This function is a convenient system for locking and unlocking all the doors at a distance. The operation of this function in the smart entry and start system is the same as that of the wireless door lock control system. However, the receiver in the certification ECU (smart key ECU assembly) uses a door control receiver to perform the control.
Entry Unlock When a key is located in the exterior actuation area of the outside handle of the driver door, pressing a lock/unlock switch will cause all doors to unlock.
Entry Lock*1 When a key is located in the exterior actuation area of the outside handle of the driver door and the engine switch is off (Lock), all doors can be locked by simply pressing the lock/unlock switch.
Entry Lock*2 When a key is located in the exterior actuation area of the outside handle of the driver door and the engine switch is off (Lock), all doors can be locked by simply pressing the lock/unlock switch or pressing the back door lock switch.
Luggage Compartment Door Open*1 When a key is in an exterior actuation area of the center of the luggage compartment door, the luggage compartment door can be opened manually by simply pressing the luggage electrical key switch.
Back Door Open*2 When a key is in an exterior actuation area of the center of the back door, the back door can be opened manually by simply pressing the back door opener switch.
Prevention of Key Confinement Prevents the confinement of the key if the door is locked from the door outside handle while the key is still inside the vehicle. When locking the doors while the key is inside the vehicle, a buzzer sounds to prevent the key from being confined.
Warning The smart entry and start system causes the certification ECU (smart key ECU assembly) to sound the buzzer in the combination meter assembly and wireless door lock buzzer and indicates a warning on the multi-information display*3 or the smart warning light*4 in order to alert the driver.
Battery Saving When the vehicle remains unused for a long period of time, a battery saving function can prevent discharge of the electrical key transmitter sub-assembly battery.
Key Cancel The following key functions can be cancelled by following certain procedures:
·

Entry unlock/lock

·

Luggage compartment door open*1

·

Back door open*2

·

Prevention of key confinement

·

Warning


Key Code Registration Function A total of 4 keys can be registered. Key registration enables the registering (writing and storing) of transmitter recognition codes in the EEPROM that is contained in the certification ECU (smart key ECU assembly).



b.

Wireless Door Lock Control Function

i.

The wireless door lock control function has the following functions:

Function Outline

*: for sedan

All Doors Lock Pressing the lock button of the electrical key transmitter sub-assembly locks all doors.
All Doors Unlock Pressing the unlock button of the electrical key transmitter sub-assembly unlocks all doors.
Luggage Compartment Door Open* Pressing the luggage compartment door open button of the electrical key transmitter sub-assembly for longer than approximately 0.8 seconds opens the luggage compartment door.
Automatic Lock If none of the doors are opened for approximately 30 seconds after being unlocked by the wireless door lock control, all the doors are locked again automatically.
Answer Back The hazard light blinks once and wireless door lock buzzer sounds when locking, and blinks twice when unlocking, to inform that the operation has been completed.
Door Ajar Warning If any door is open or ajar, pressing the lock button of the electrical key transmitter sub-assembly will cause the wireless door lock buzzer to sound for about 5 seconds as a warning.



c.

Entry Unlock

i.

While the user carries the key in the exterior actuation area, and presses the lock/unlock switch of the front door outside handle (driver side).

Y217173C02
3.938,0.865 4.75,0.333 4.75,0.333 4.917,0.333 true 4.969,0.229 5.167,0.417 0.198,0.188 10 false *1 0.156,1.469 0.354,1.677 0.198,0.208 10 false *a
*1 Lock/unlock Switch - -
*a The illustrations shown are examples only. - -



ii.

When the doors are unlocked, the hazard warning lights flash twice as an answer back.



d.

Entry Lock

i.

When the user gets out of the vehicle while carrying the key and presses the lock/unlock switch of the front door outside handle (driver side) within the exterior actuation area with all the doors closed, the doors are locked.


ii.

For hatchback, when the user gets out of the vehicle while carrying the key and presses the back door lock switch within the back door exterior actuation area with all the doors closed, the doors are locked.

Y215223C01
5.344,2.156 5.51,2.156 5.51,2.156 5.896,1.51 true 5.156,2.063 5.469,2.219 0.313,0.156 10 false *1 0.188,2.396 0.5,2.552 0.313,0.156 10 false *a
*1 Back Door Lock Switch - -
*a The illustrations shown are examples only. - -



iii.

When the doors are locked, the hazard warning lights flash once as an answer back.



e.

Luggage Compartment Door Open (for Sedan)

i.

The luggage compartment door is opened when the luggage electrical key switch is pressed within the luggage compartment door exterior actuation area while the user is carrying the key.

Y215224C01
5.271,2.021 5.438,2.021 5.438,2.021 5.688,1.604 true 5.083,1.927 5.396,2.083 0.313,0.156 10 false *1 0.167,2.365 0.479,2.521 0.313,0.156 10 false *a
*1 Luggage Electrical Key Switch - -
*a The illustrations shown are examples only. - -




f.

Back Door Open (for Hatchback)

i.

The back door is opened and all doors are unlocked when the back door opener switch is pressed within the back door exterior actuation area while the user is carrying the key.

Y215223C02
5.167,2.083 5.333,2.083 5.333,2.083 5.5,1.365 true 4.969,1.99 5.281,2.146 0.313,0.156 10 false *1 0.25,2.469 0.521,2.677 0.271,0.208 10 false *a
*1 Back Door Opener Switch - -
*a The illustrations shown are examples only. - -




g.

Warning Function

i.

When any of the situations below occur, the smart entry and start system sounds the wireless door lock buzzer and a buzzer in the combination meter assembly and displays a message on the multi-information display*1 and illuminates the smart warning light*2 in order to alert the driver.

*1: Models with color type multi-information display

*2: Models with monochrome type multi-information display

Situation Condition
A The engine is left running and the shift lever is in a position other than P when the driver gets out of the vehicle.
B The driver door is opened while the steering is unlocked.
C The engine is left running when a passenger gets out of the vehicle while holding the electrical key transmitter.
D The electrical key transmitter is not within the actuation areas.
E The vehicle is driven without an electrical key transmitter.
F The electrical key transmitter is left in the vehicle.
G A door is ajar.
H The key reminder sounds.
I The key battery is weak.
J Steering lock does not release.
K A malfunction has been detected in a vehicle speed signal, etc.
L The engine cannot be started (system/driver error).
M Immobiliser system certification confirmation occurs.
N Engine start operation guide (ACC ON)
O Engine start operation guide (IG ON)
P The engine switch cannot be turned off (shift lever in any position except P).
Q The engine switch cannot be turned off (shift lever in P).
R Auto power off operation occurs.
S Engine emergency stop operation is performed.
T Engine switch is operated while driving.
U Engine switch is operated while driving.
V Accessory state
W Ignition on state


ii.

Situation A (Models with CVT)

There are 2 patterns for situation A.

Pattern 1:

When the shift lever is in a position other than P, the driver opens the door and attempts to get out of the vehicle.

In this situation, the following control is performed:

*1: Models with monochrome type multi-information display

*2: Models with color type multi-information display

Possible Effects without Warning Sudden vehicle movement, Vehicle theft, Vehicle roll-away (Vehicle creep, such as when N is selected)
Warning Active Condition The warning is activated when all of the following conditions are met:
·

The engine switch is on (ACC) or on (IG).

·

The shift lever is in any position except P.

·

The driver door is opened.

·

The vehicle speed is not detected.


Warning Method Combination Meter Assembly Buzzer Sounds continuously
Smart Warning Light*1 -
Wireless Door Lock Buzzer -
Multi-information Display*2 The following warning message is displayed:
·

Shift to P Position When Parked


Warning Stop Condition The warning is stopped when one of the following conditions is met:
·

The engine switch is turned off.

·

The shift lever is moved to P.

·

The driver door is closed.

·

The vehicle speed is above 5 km/h (3 mph).



Pattern 2:

Under the situation of pattern 1, the driver closes the door and attempts to leave the vehicle while holding the electrical key transmitter.

In this situation, the following control is performed:

*1: Models with monochrome type multi-information display

*2: Models with color type multi-information display

Possible Effects without Warning Sudden vehicle movement, Vehicle theft, Vehicle roll-away (Vehicle creep, such as when N is selected)
Warning Active Condition The warning is activated when all of the following conditions are met:
·

The engine switch is on (ACC) or on (IG).

·

The shift lever is in any position except P.

·

The driver door is opened → closed.

·

The electrical key transmitter is not detected in the vehicle (interior key certification fails).

·

The vehicle speed is not detected.


Warning Method Combination Meter Assembly Buzzer Sounds continuously
Smart Warning Light*1 Blinks yellow
Wireless Door Lock Buzzer Sounds continuously
Multi-information Display*2 The following warning messages are alternately displayed:
·

Shift to P Position When Parked

·

Key Not Detected Check Key Location


Buzzer and Wireless Door Lock Buzzer Warning Stop Condition The warning is stopped when one of the following conditions is met:
·

The engine switch is turned off.

·

The shift lever is moved to P.

·

The vehicle speed is above 5 km/h (3 mph).

·

The electrical key transmitter is detected in the vehicle (interior key certification result is OK).


"Shift to P Position When Parked" Message Warning Stop Condition The warning is stopped when either of the following conditions is met:
·

The shift lever is moved to P.

·

The vehicle speed is above 5 km/h (3 mph).


"Key Not Detected Check Key Location" Message and Smart Warning Light Warning Stop Condition The warning is stopped when either of the following conditions is met:
·

The engine switch is turned off.

·

The electrical key transmitter is detected in the vehicle (interior key certification result is OK).






iii.

Situation B

There are 3 patterns for situation B.

Pattern 1:

When the shift lever is in P*1 and the engine switch is in a mode other than off (the steering remains unlocked), the driver door is opened and the driver attempts to leave the vehicle.

In this situation, the following control is performed:

*1: Models with CVT

*2: Models with monochrome type multi-information display

*3: Models with color type multi-information display

Possible Effects without Warning Vehicle theft
Warning Active Condition Condition 1
The warning is activated when both of the following conditions are met:
·

The engine switch is on (ACC).

·

The driver door is open.


Condition 2
The warning is activated when all of the following conditions are met for 1 second:
·

The engine switch is turned off.

·

The steering lock remains unlocked.

·

The driver door is open.


Warning Method Combination Meter Assembly Buzzer Sounds continuously at short and even intervals
Smart Warning Light*2 -
Wireless Door Lock Buzzer -
Multi-information Display*3 -
Warning Stop Condition The warning is stopped when one of the following conditions is met:
·

The engine switch is turned on (IG).

·

The driver door is closed.

·

The engine switch is turned off and the steering wheel lock control is performed.



Pattern 2:

Under the situation of pattern 1, the driver opens and closes the driver door and attempts to leave the vehicle while holding the electrical key transmitter.

In this situation, the following control is performed:

*1: Models with CVT

*2: Models with monochrome type multi-information display

*3: Models with color type multi-information display

Possible Effects without Warning Vehicle theft
Warning Active Condition The warning is activated when all of the following conditions are met:
·

The engine switch is on (ACC) or on (IG).

·

The shift lever is in P. *1

·

The driver door is opened → closed.

·

The electrical key transmitter is not detected in the vehicle (interior key certification fails).

·

The vehicle speed is not detected.


Warning Method Combination Meter Assembly Buzzer Sounds once
Smart Warning Light*2 Blinks yellow
Wireless Door Lock Buzzer Sounds 3 times
Multi-information Display*3 The following warning message is displayed:
·

Key Not Detected Check Key Location


Warning Stop Condition The warning is stopped when either of the following conditions is met:
·

The engine switch is turned off.

·

The electrical key transmitter is detected in the vehicle (interior key certification result is OK).



Pattern 3:

Under the situation of pattern 2, the driver touches the lock switch on a front door outside handle assembly.

In this situation, the following control is performed:

*1: Models with CVT

*2: Models with monochrome type multi-information display

*3: Models with color type multi-information display

Possible Effects without Warning Vehicle theft
Warning Active Condition The warning is activated when all of the following conditions are met:
·

The engine switch is on (ACC) or on (IG).

·

The shift lever is in P. *1

·

The electrical key transmitter is not detected in the vehicle (interior key certification fails), but detected in an outside detection area (exterior key certification result is OK).

·

The lock switch on a front door outside handle assembly is on (pressed).

·

The vehicle speed is not detected.


Warning Method Combination Meter Assembly Buzzer Sounds once
Smart Warning Light*2 Blinks yellow
Wireless Door Lock Buzzer Sounds continuously
Multi-information Display*3 The following warning messages are alternately displayed:
·

Turn Power Off

·

Key Not Detected Check Key Location


Wireless Door Lock Buzzer Warning Stop Condition The warning is stopped when one of the following conditions is met:
·

5 seconds elapse.

·

The engine switch is turned off.

·

The shift lever is moved to any position except P. *1

·

The vehicle speed is above 5 km/h (3 mph).

·

The electrical key transmitter is detected in the vehicle (interior key certification result is OK).

·

Any door is opened or closed.


"Turn Power Off" Message Warning Stop Condition The warning is stopped when one of the following conditions is met:
·

60 seconds elapse.

·

The engine switch is turned off.

·

The shift lever is moved to any position except P. *1

·

The vehicle speed is above 5 km/h (3 mph).


"Key Not Detected Check Key Location" Message and Smart Warning Light Warning Stop Condition The warning is stopped when either of the following conditions is met:
·

The engine switch is turned off.

·

The electrical key transmitter is detected in the vehicle (interior key certification result is OK).






iv.

Situation C

When the engine is left running, a passenger leaves the vehicle while holding the electrical key transmitter.

In this situation, the following control is performed:

*1: Models with monochrome type multi-information display

*2: Models with color type multi-information display

Possible Effects without Warning Engine cannot be restarted.
Warning Active Condition The warning is activated when all of the following conditions are met:
·

The engine switch is on (ACC) or on (IG).

·

A door other than the driver door is opened → closed.

·

The electrical key transmitter is not detected in the vehicle (interior key certification fails).

·

The vehicle speed is not detected.


Warning Method Combination Meter Assembly Buzzer Sounds once
Smart Warning Light*1 Blinks yellow
Wireless Door Lock Buzzer Sounds 3 times
Multi-information Display*2 The following warning message is displayed:
·

Key Not Detected Check Key Location


Warning Stop Condition The warning is stopped when either of the following conditions is met:
·

The engine switch is turned off.

·

The electrical key transmitter is detected in the vehicle (interior key certification result is OK).





v.

Situation D

When the electrical key transmitter is not in the vehicle, the driver attempts to turn the engine switch on (IG) (emergency key operation*1 is included).

In this situation, the following control is performed:

*1: The emergency key operation is an operation that changes the power source by touching the engine switch with the electrical key transmitter.

*2: Models with monochrome type multi-information display

*3: Models with color type multi-information display

Possible Effects without Warning User becomes confused
Warning Active Condition The warning is activated when all of the following conditions are met:
·

The immobiliser system is set.

·

The electrical key transmitter is not in the vehicle (interior key certification fails and transponder certification fails).

·

No records of unlock operation using a mechanical key and key certification failure when the engine switch was turned on (IG).


Warning Method Combination Meter Assembly Buzzer Sounds once
Smart Warning Light*2 Blinks yellow
Wireless Door Lock Buzzer -
Multi-information Display*3 The following warning message is displayed:
·

Key Not Detected Check Key Location


Warning Stop Condition The warning is stopped when one of the following conditions is met:
·

15 seconds elapse.

·

The electrical key transmitter is detected in the vehicle (interior key certification result is OK and transponder certification result is OK).

·

30 seconds have elapsed since a door was opened using a door outside handle assembly.





vi.

Situation E

The vehicle starts moving without a registered electrical key transmitter in the vehicle.

In this situation, the following control is performed:

*1: Models with monochrome type multi-information display

*2: Models with color type multi-information display

Possible Effects without Warning Engine cannot be restarted.
Warning Active Condition The warning is activated when all of the following conditions are met:
·

The engine switch is on (IG).

·

The warning is activated in situation C.

·

The vehicle speed is above 5 km/h (3 mph).

·

The electrical key transmitter is not detected in the vehicle (interior key certification fails).


Warning Method Combination Meter Assembly Buzzer Sounds 9 times
Smart Warning Light*1 Blinks yellow
Wireless Door Lock Buzzer -
Multi-information Display*2 The following warning message is displayed:
·

Key Not Detected Check Key Location


Warning Stop Condition The warning is stopped when either of the following conditions is met:
·

The engine switch is turned off.

·

The electrical key transmitter is detected in the vehicle (interior key certification result is OK).





vii.

Situation F

The lock switch on a front door outside handle assembly is pressed to perform entry lock with the electrical key transmitter left in the vehicle.

In this situation, the following control is performed:

*1: Models with monochrome type multi-information display

*2: Models with color type multi-information display

Possible Effects without Warning Vehicle theft
Warning Active Condition The warning is activated when all of the following conditions are met:
·

The engine switch is off.

·

All doors are closed.

·

The electrical key transmitter is detected in the vehicle (interior key certification result is OK).

·

The lock switch on a front door outside handle assembly is on (pressed).

·

Any door is unlocked.

·

The vehicle speed is not detected.


Warning Method Combination Meter Assembly Buzzer -
Smart Warning Light*1 -
Wireless Door Lock Buzzer Sounds continuously
Multi-information Display*2 The following warning message is displayed:
·

Key Detected in Vehicle


Wireless Door Lock Buzzer Warning Stop Condition The warning is stopped when any of the following conditions is met:
·

5 seconds elapse.

·

The engine switch is turned on (ACC) or on (IG).

·

The vehicle speed is above 5 km/h (3 mph).

·

Any door is opened.

·

Lock operation is detected.


"Key Detected in Vehicle" Message Warning Stop Condition The warning is stopped when any of the following conditions is met:
·

60 seconds elapse.

·

The engine switch is turned on (ACC) or on (IG).

·

The vehicle speed is above 5 km/h (3 mph).

·

Lock operation is detected.





viii.

Situation G

The lock switch on a front door outside handle assembly is pressed to perform entry lock, however, a door is open.

In this situation, the following control is performed:

*1: Models with monochrome type multi-information display

*2: Models with color type multi-information display

Possible Effects without Warning Vehicle theft
Warning Active Condition The warning is activated when all of the following conditions are met:
·

The engine switch is off.

·

Any door is open other than the door where the entry lock operation is performed.

·

The lock switch on a front door outside handle assembly is on (pressed) or the lock switch on the electrical key transmitter is pressed.

·

The electrical key transmitter is in an outside detection area (exterior key certification result is OK).


Warning Method Combination Meter Assembly Buzzer -
Smart Warning Light*1 -
Wireless Door Lock Buzzer Sounds continuously
Multi-information Display*2 -
Warning Stop Condition The warning is stopped when one of the following conditions is met:
·

5 seconds elapse.

·

The engine switch is turned on (ACC) or on (IG).

·

All doors are closed.

·

Unlock operation is performed using the wireless door lock remote function.

·

Unlock operation is performed using the unlock switch on a front door outside handle assembly.





ix.

Situation H

The door is locked with the electrical key transmitter left in the vehicle.

In this situation, the following control is performed:

*1: Keyless lock operation is door lock operation without using the electrical key transmitter. First, set the lock position (door lock knob) when the door is open, and close the door while pulling the door handle to lock the door.

*2: Models with monochrome type multi-information display

*3: Models with color type multi-information display

Possible Effects without Warning Vehicle theft
Warning Active Condition The warning is activated when all of the following conditions are met:
·

The door is locked using the keyless lock operation.*1

·

The electrical key transmitter is in the vehicle (interior key certification result is OK).

·

The vehicle speed is not detected.


Warning Method Combination Meter Assembly Buzzer Sounds once
Smart Warning Light*2 -
Wireless Door Lock Buzzer Sounds continuously
Multi-information Display*3 The following warning message is displayed:
·

Key Detected in Vehicle


Wireless Door Lock Buzzer Warning Stop Condition The warning is stopped when one of the following conditions is met:
·

5 seconds elapse.

·

The power source mode is changed to another mode.

·

Any door is opened.

·

Lock operation is detected.

·

The vehicle speed is above 5 km/h (3 mph).


"Key Detected in Vehicle" Message Warning Stop Condition The warning is stopped when one of the following conditions is met:
·

60 seconds elapse.

·

The power source mode is changed to another mode.

·

Lock operation is detected.

·

The vehicle speed is above 5 km/h (3 mph).





x.

Situation I

The vehicle is driven using an electrical key transmitter that has a low battery.

In this situation, the following control is performed:

*1: Warning performed 20 minutes after the engine switch is turned on (IG)

*2: Models with monochrome type multi-information display

*3: Models with color type multi-information display

Possible Effects without Warning Usability function, engine cannot be restarted
Warning Active Condition Condition 1: The warning is activated when all of the following conditions are met:
·

The engine switch is turned off after being left on (IG) for more than 20 minutes.

·

The key battery voltage is low (key battery low code is received).

·

The electrical key transmitter is in the vehicle (interior key certification result is OK).

·

The vehicle speed is not detected.


Condition 2: The warning is activated when all of the following conditions are met:
·

The engine is stopped → restarted (engine speed is 200 rpm or more).

·

The key battery voltage is low (key battery low code is received).

·

The electrical key transmitter is in the vehicle (interior key certification result is OK).

·

The vehicle speed is not detected.

·

The low key battery warning for condition 1 was performed.*1


Warning Method Combination Meter Assembly Buzzer Sounds once
Smart Warning Light*2 Blinks yellow
Wireless Door Lock Buzzer -
Multi-information Display*3 The following warning message is displayed:
·

Key Battery Low Replace Key Battery


Warning Stop Condition The warning is stopped when either of the following conditions is met:
·

15 seconds elapse.

·

The vehicle speed is above 5 km/h (3 mph).





xi.

Situation J

The steering lock cannot be released or the shift lever is moved to a position other than P*1 before the steering lock is unlocked.

In this situation, the following control is performed:

*1: Models with CVT

*2: Models with monochrome type multi-information display

*3: Models with color type multi-information display

Possible Effects without Warning Usability function
Warning Active Condition The warning is activated when the following condition is met:
The steering lock cannot be released (the steering lock ECU judgment).
Warning Method Combination Meter Assembly Buzzer Sounds once
Smart Warning Light*2 Blinks green (fast)
Wireless Door Lock Buzzer -
Multi-information Display*3 The following warning message is displayed:
·

Push ENGINE Switch while Turning Steering Wheel in Either Direction


Warning Stop Condition The engine switch is pressed while the steering wheel is turned left and right.
The warning is stopped when either of the following conditions is met:
·

15 seconds elapse.

·

The steering lock is released.





xii.

Situation K

A vehicle speed signal malfunction or malfunction that interferes with steering lock ECU (steering lock actuator assembly) operation has been detected.

In this situation, the following control is performed:

*1: Models with manual transaxle

*2: Models with monochrome type multi-information display

*3: Models with color type multi-information display

Possible Effects without Warning Malfunction Detection
Warning Active Condition The warning is activated when either of the following conditions is met:
·

The steering lock ECU (steering lock actuator assembly), driver of the certification ECU (smart key ECU assembly) or steering lock/unlock position switch is malfunctioning.

·

Power source mode is off (Lock), clutch start switch assembly*1 remains ON for 5 minutes or more, and driver door is closed → opened.

·

An IG relay output circuit error has been detected.

·

The vehicle speed is judged as abnormal or vehicle speed signal communication is malfunctioning.


Warning Method Combination Meter Assembly Buzzer Sounds once
Smart Warning Light*2 Blinks yellow
Wireless Door Lock Buzzer -
Multi-information Display*3 The following warning message is displayed:
·

Entry & Start System Malfunction See Owner's Manual


Warning Stop Condition The warning is stopped when either of the following conditions is met:
·

15 seconds elapse.

·

The system returns to normal.





xiii.

Situation L

When the driver attempts to start the engine after unlocking the driver door using the mechanical key, the electrical key transmitter cannot be detected in the vehicle or cannot be detected in the vehicle 2 times in a row.

In this situation, the following control is performed:

*1: Models with monochrome type multi-information display

*2: Models with color type multi-information display

Possible Effects without Warning Usability function
Warning Active Condition The warning is activated when the engine switch is pressed with all of the following conditions met:
·

The immobiliser system is set.

·

The electrical key transmitter is not detected in the vehicle (interior key certification fails).

·

The doors were unlocked using a mechanical key or when the engine switch is pressed, a certification error occurs 2 times in a row.


Warning Method Combination Meter Assembly Buzzer Sounds once
Smart Warning Light*1 Blinks yellow
Wireless Door Lock Buzzer -
Multi-information Display*2 The following warning message is displayed for 60 seconds (and then automatically turned off):
·

Depress Brake Pedal and Touch ENGINE Switch with Key


Warning Stop Condition The warning is stopped when one of the following conditions is met:
·

60 seconds elapse.

·

The electrical key transmitter is detected in the vehicle (interior key certification result is OK and transponder certification result is OK.).

·

30 seconds have elapsed since the door was opened using a door outside handle assembly.





xiv.

Situation M

The engine switch is touched with an electrical key transmitter when the transmitter battery voltage is low, smart operation is canceled or radio interference occurs.

In this situation, the following control is performed:

*1: Models with monochrome type multi-information display

*2: Models with color type multi-information display

Possible Effects without Warning Usability function
Warning Active Condition Transponder certification result is OK.
Warning Method Combination Meter Assembly Buzzer Sounds once
Smart Warning Light*1 -
Wireless Door Lock Buzzer -
Multi-information Display*2 The following warning message is displayed:
·

Depress Brake Pedal and Push ENGINE Switch to Start


Warning Stop Condition The warning is stopped when either of the following conditions is met:
·

10 seconds elapse.

·

The electrical key transmitter is detected in the vehicle (interior key certification result is OK).

·

The engine is running at 500 rpm or more.

·

The engine is started.

·

The immobiliser system is set and interior certification is stopped or key certification fails.





xv.

Situation N

The system recognizes a situation that indicates the driver may start the engine (when the driver enters the vehicle or the engine switch is on (ACC)).

In this situation, the following control is performed:

*1: Models with monochrome type multi-information display

*2: Models with color type multi-information display

Possible Effects without Warning Usability function
Warning Active Condition The warning is activated when either of the following conditions is met:
·

When the door is unlocked from the outside of the vehicle with the engine switch off, the driver door is closed → opened.

·

Each time the power source mode is changed from off to on (ACC) without the brake pedal depressed.


Warning Method Combination Meter Assembly Buzzer -
Smart Warning Light*1 -
Wireless Door Lock Buzzer -
Multi-information Display*2 The following warning message is displayed:
·

Depress Brake Pedal and Push ENGINE Switch to Start


Warning Stop Condition The warning is stopped when one of the following conditions is met:
·

20 seconds have elapsed since the warning started.

·

The engine is running.

·

Door lock operation is performed from the outside of the vehicle.

·

Wireless operation is performed from the inside of the vehicle or door lock operation is performed using a keyless lock function.





xvi.

Situation O

The system recognizes a situation that indicates the driver may start the engine (when the engine switch is on (IG)).

In this situation, the following control is performed:

*1: Models with monochrome type multi-information display

*2: Models with color type multi-information display

Possible Effects without Warning Usability function
Warning Active Condition The warning is activated when either of the following conditions is met:
·

Each time the power source mode is changed from off to on (IG) (the engine is not started) with the shift lever in P or N and without the brake pedal depressed.

·

When the engine switch is on (IG) (the engine is not started) with the shift lever in a position other than P or N, the shift lever is moved to P or N.


Warning Method Combination Meter Assembly Buzzer -
Smart Warning Light*1 -
Wireless Door Lock Buzzer -
Multi-information Display*2 The following warning message is displayed:
·

Depress Brake Pedal and Push ENGINE Switch to Start


Warning Stop Condition The warning is stopped when one of the following conditions is met:
·

The power source mode is changed to any mode other than on (IG).

·

The vehicle speed is above 5 km/h (3 mph).

·

The shift lever is in a position other than P or N.





xvii.

Situation P

The driver attempts to turn the engine switch off with the shift lever in any position other than P or N.

In this situation, the following control is performed:

*1: Models with monochrome type multi-information display

*2: Models with color type multi-information display

Possible Effects without Warning Discharged vehicle battery, vehicle roll-away (vehicle creep, such as when N is selected)
Warning Active Condition The engine switch is turned off when the shift lever is in a mode other than P or N. (Excluding an emergency stop by pressing the engine switch 3 times quickly or pressing and holding the engine switch for 2 seconds or more.)
Warning Method Combination Meter Assembly Buzzer Sounds once
Smart Warning Light*1 -
Wireless Door Lock Buzzer -
Multi-information Display*2 The following warning message is displayed:
·

Shift to P Position When Parked


Warning Stop Condition The warning is stopped when either of the following conditions is met:
·

The shift lever is moved to P.

·

The power source mode is changed to a mode other than on (ACC).





xviii.

Situation Q

Under the situation P the shift lever is moved to P.

In this situation, the following control is performed:

*1: Models with monochrome type multi-information display

*2: Models with color type multi-information display

Possible Effects without Warning Discharged vehicle battery, vehicle roll-away (vehicle creep, such as when N is selected)
Warning Active Condition The shift lever is moved to P.
Warning Method Combination Meter Assembly Buzzer Sounds once
Smart Warning Light*1 -
Wireless Door Lock Buzzer -
Multi-information Display*2 The following warning message is displayed:
·

Turn Power Off


Warning Stop Condition The warning is stopped when either of the following conditions is met:
·

The power source mode is changed to a mode other than on (ACC).

·

The shift lever is in any position other than P.





xix.

Situation R

Automatic power off operation occurs.

In this situation, the following control is performed:

*1: Models with monochrome type multi-information display

*2: Models with color type multi-information display

Possible Effects without Warning Usability function
Warning Active Condition The warning is activated when all of the following conditions are met:
·

The shift lever is in P.

·

The engine switch is on (ACC) or on (IG).

·

The vehicle speed is not detected and the engine is stopped.

·

The power source is turned off by the automatic power off function (the vehicle remains not operated for 20 minutes with the engine switch on (ACC) or for 1 hour with the engine switch on (IG)).


Warning Method Combination Meter Assembly Buzzer -
Smart Warning Light*1 -
Wireless Door Lock Buzzer -
Multi-information Display*2 The following warning message is displayed:
·

Auto Power Off to Conserve Battery


Warning Stop Condition The warning is stopped when either of the following conditions is met:
·

10 seconds have elapsed since the warning started.

·

The engine switch is turned on (ACC) or on (IG).





xx.

Situation S

The driver stopped the engine using emergency operation while driving.

In this situation, the following control is performed:

*1: Models with monochrome type multi-information display

*2: Models with color type multi-information display

Possible Effects without Warning Usability function
Warning Active Condition The warning is activated when either of the following conditions is met:
·

The engine is stopped by emergency stop operation while driving.

·

After emergency stop operation, the engine switch is turned on (IG), the vehicle speed is detected and the engine is not started.


Warning Method Combination Meter Assembly Buzzer Sounds continuously
Smart Warning Light*1 -
Wireless Door Lock Buzzer -
Multi-information Display*2 The following warning message is displayed:
·

Shift to N Position and Push ENGINE Switch to Restart


Warning Stop Condition The warning is stopped when one of the following conditions is met:
·

The shift lever is moved to P.

·

The vehicle speed is not detected (after the power source mode is changed to on (IG) using engine switch operation).

·

The engine switch is operated.

·

The engine has started.





xxi.

Situation T

The driver pressed the engine switch while driving.

In this situation, the following control is performed:

*1: Models with monochrome type multi-information display

*2: Models with color type multi-information display

Possible Effects without Warning Wrong operation is prevented
Warning Active Condition The vehicle is moving, the vehicle speed is detected and the engine switch is pressed.
Warning Method Combination Meter Assembly Buzzer Sounds intermittently
Smart Warning Light*1 -
Wireless Door Lock Buzzer -
Multi-information Display*2 -
Warning Stop Condition The warning is stopped when either of the following conditions is met:
·

2 seconds have elapsed since the engine switch operation was stopped.

·

The engine switch is turned off.





xxii.

Situation U

The driver pressed the engine switch while driving.

In this situation, the following control is performed:

Possible Effects without Warning Usability function
Warning Active Condition The vehicle is moving, the vehicle speed is detected and the engine switch is pressed.
Warning Method Combination Meter Assembly Buzzer Sounds once
Wireless Door Lock Buzzer -
Multi-information Display The following warning message is displayed:
·

Push and Hold ENGINE Switch for Emergency Stop


Warning Stop Condition The warning is stopped when either of the following conditions is met:
·

10 seconds elapse.

·

The engine switch is turned off.





xxiii.

Situation V

The power source is changed to on (ACC). In this situation, the following control is performed:

*1: Models with monochrome type multi-information display

*2: Models with color type multi-information display

Possible Effects without Warning Usability function
Warning Active Condition The power source is changed to on (ACC).
Warning Method Combination Meter Assembly Buzzer -
Smart Warning Light*1 Blinks green (slow)
Wireless Door Lock Buzzer -
Multi-information Display*2 ACCESSORY
Warning Stop Condition The warning is stopped when the following condition is met:
·

The power source is changed to a mode other than on (ACC).




xxiv.

Situation W

The power source is changed to on (IG). In this situation, the following control is performed:

*1: Models with monochrome type multi-information display

*2: Models with color type multi-information display

Possible Effects without Warning Usability function
Warning Active Condition The power source is changed to on (IG).
Warning Method Combination Meter Assembly Buzzer -
Smart Warning Light*1 Blinks green (slow)
Wireless Door Lock Buzzer -
Multi-information Display*2 IGNITION ON
Warning Stop Condition The warning is stopped when either of the following conditions is met:
·

The power source is changed to a mode other than on (IG).

·

The display in the odometer area is changed due to user operation.





h.

Battery Saving Function of Electrical Key Transmitter Sub-assembly

i.

This function cancels the signal reception waiting state of the electrical key transmitter sub-assembly, reducing the consumption of current from its battery.


ii.

The electrical key transmitter sub-assembly can be placed into and taken out of battery saving mode. When the electrical key transmitter sub-assembly is in battery saving mode, the smart entry and start system will not be able to detect the transmitter, as the transmitter will not respond to signals from the vehicle. The function of the smart entry and start system will not operate if the electrical key transmitter sub-assembly is in battery saving mode.


iii.

Pressing the unlock switch of the electrical key transmitter sub-assembly twice while pressing the lock switch (the indicator light of the electrical key transmitter sub-assembly blinks 4 times) selects battery saving mode for the electrical key transmitter sub-assembly.


iv.

Battery saving mode can be canceled by pressing any switch on the electrical key transmitter sub-assembly.



i.

Key Cancel Function

i.

A key cancel function is provided to make it possible to disable the smart entry and start system. Key cancel can be operated when certain operations are performed when the vehicle is under the following conditions:

·

Engine switch is off (Lock).

·

Driver door is closed.

·

Driver door is unlocked.



ii.

The operation procedure is as follows:

1.

Press the unlock button of the electrical key transmitter sub-assembly.

2.

Open the driver door within 5 seconds of completing the step above (driver door: close condition → opened).

3.

With the driver door open, press the unlock button of the electrical key transmitter sub-assembly 2 times within 5 seconds of completing the step above.

NOTICE:

If the driver door is closed before or while pressing the unlock button, the entry cancel setting mode will end.


4.

Finish the step (a) to (c) within the 30 seconds of completing the step above.

1.

Close and open the driver door twice (driver door: open condition → closed → opened → closed → opened).

2.

With the driver door open, press the unlock button of the electrical key transmitter sub-assembly 2 times.

NOTICE:

If the driver door is closed before or while pressing the unlock button, the entry cancel setting mode will end.


3.

Close and open the driver door (driver door: open condition → closed → opened).


5.

Close the driver door within 5 seconds of completing the above step.

6.

Check that the wireless buzzer sounds twice (short beeps) to confirm that the smart entry and start system has been canceled.




j.

Key Code Registration Function

i.

The table below shows the 3 special ID code registration function modes through which up to 4 different transmitter recognition codes can be registered. The codes are electronically registered (written to and stored) in the EEPROM. For details, refer to the corresponding Service Bulletin for this model.

Mode Mode Function
Rewrite Clears all previously registered codes and registers only the newly received codes. This mode is used whenever a transmitter or the certification ECU (smart key ECU assembly) is replaced.
Add Adds a newly received code while preserving previously registered codes. This mode is used when adding a new transmitter. If the number of codes exceeds 4, the oldest registered code is cleared first.
Confirm Confirms how many codes are currently registered. When adding a new code, this mode is used to check how many codes already exist.




DIAGNOSIS


a.

The certification ECU (smart key ECU assembly) can detect malfunctions in the smart entry and start system when the power source is on (IG).


b.

When the ECU detects a malfunction, smart warning light*1 blinks in the yellow or a message is displayed on the multi-information display*2 to warn the driver. At the same time, the ECU stores a 5-digit Diagnostic Trouble Code (DTC) in its memory.


c.

The 5-digit DTCs can be read after connecting the Global TechStream (GTS) to the DLC3.


d.

The smart entry and start system may not operate successfully if a malfunction occurs.


e.

For details, refer to the Repair Manual.

*1: Models with monochrome type multi-information display

*2: Models with color type multi-information display