SYSTEM CONTROL
Eco Driving Indicator Light (Models with CVT)
Eco Driving Indicator Light starts to operate when the following conditions are met:
|
*: Models with shift paddle switch |
|
| Condition | ·
Ignition switch is ON. ·
Engine is running. ·
Shift lever is in D. ·
Shift paddle switch is not operating.* ·
When the vehicle is at a speed of 130 km/h (81 mph) or below. |
Eco Driving Indicator Light stops operation when any of the following conditions is met:
|
*: Models with shift paddle switch |
|
| Condition | ·
Ignition switch is off. ·
Engine is stopped. ·
Shift lever is in any position other than D. ·
Shift paddle switch is operating.* ·
When the vehicle is at a speed of 130 km/h (81 mph) or over. |
When the ECM determines that Eco driving (environment-friendly acceleration operation) is being performed, the ECM outputs an Eco Driving Indicator Light illumination request signal to the combination meter assembly and illuminates the Eco Driving Indicator Light.
Eco Driving Indicator Zone Display (Models with Color Type Multi-information Display)
Eco Driving Indicator Zone Display can operate when all of the following conditions are met:
Ignition switch is ON and the engine is running.
Shift lever is in D.
When the vehicle is at a speed of 130 km/h (81 mph) or below.
The following table shows the operation of Eco Driving Indicator Zone Display under different driving conditions:
| Driving Condition | Eco Driving Indicator Light | Eco Driving Indicator Zone Display |
|---|---|---|
·
While stopped ·
When any of the following conditions is met, operation is stopped: ·
Engine is stopped. ·
Shift lever is in any position other than D. ·
When the vehicle is at a speed of 130 km/h (81 mph) or over. |
Turns off |
|
| During Eco Driving | Turns on |
|
| During Non-Eco Driving | Turns off |
|
Front Seat Belt Warning (Models for the regions except for G.C.C. Countries)
When the ignition switch is ON, this system detects the state of the seat belts based on the signals from the front seat belt buckle switch (driver side and passenger side*).
The front seat belt warning light located in the combination meter is used for the driver and front passenger* seats.
After the ignition switch is turned ON, if the driver or front passenger* has not fastened their seat belt, the seat belt warning light will begin flashing.
When the seat belt remains unfastened and the vehicle speed reaches approximately 20 km/h (12 mph), the buzzer will start sounding intermittently. At this time, the seat belt warning light flashing will change in sync with the intermittent buzzer sound. These buzzer and indicator warnings will continue for approximately 30 seconds until the seat belt is fastened.
If the seat belt still remains unfastened after approximately 30 seconds, the intervals of the intermittent buzzer sound and flashing light will change, and such warnings will continue for approximately 90 seconds until the seat belt is fastened.
While the seat belt warning light and buzzer are operating, fastening the seat belt will bring them to a stop.
*: Models with Front Passenger Seat Belt Warning
Front Seat Belt Warning (Models for G.C.C. Countries)
When the ignition switch is ON, this system detects the state of the seat belts based on the signals from the front seat belt buckle switch LH.
The front seat belt warning light located in the combination meter is used for the driver seat.
After the ignition switch is turned ON, if the driver seat belt has remained unfastened for 1.8 seconds, the front seat belt warning light will flash for 6 seconds. If either of the following conditions is met, the seat belt warning light will continue flashing:
The driver seat belt remains unfastened, and the vehicle is in a condition other than the conditions described below for approximately 24 seconds or more:
The vehicle speed is 0 km/h with the shift lever in P or the parking brake applied.
The driver seat belt remains unfastened, and the seat belt warning buzzer sounds just once. Furthermore, when the seat belt is not fastened within approximately 24 seconds from the time the seat belt warning buzzer started sounding periodically, the warning light will commence flashing at short intervals.
If the driver seat belt is still unfastened even after the ignition switch is turned ON, the seat belt warning buzzer will sound 5 times. And then, if the driver seat belt remains unfastened and the vehicle speed reaches approximately 20 km/h (12 mph), the seat belt warning buzzer will sound once. Furthermore, when approximately 24 seconds has elapsed with the seat belt unfastened, the seat belt warning buzzer will start sounding periodically for 9.6 seconds. If the seat belt is not fastened within this 9.6 seconds, the seat belt warning buzzer will commence sounding at short intervals.
While the seat belt warning light is flashing and the seat belt warning buzzer is sounding, fastening the seat belt will bring the warning light flashing and warning buzzer sounding to a stop.
Rear Seat Belt Warning (Models with Rear Seat Belt Warning)
If the meter ECU receives an off signal from the rear door courtesy light switch assembly when the ignition switch is ON, a rear passenger seat belt warning light is shown of the air conditioning control assembly. At this time, if the meter ECU receives an on signal from a rear seat belt buckle switch, it will extinguish the seat belt warning light corresponding to the rear seat belt buckle switch which sent the on signal. In addition, the rear passenger seat belt reminder display will automatically turn off approximately 34 seconds after the display.
If any of the rear seat belts are released while the vehicle speed is above 20 km/h (12 mph), the rear passenger seat belt reminder belt warning light illuminates and the buzzer is sounded. After 30 seconds, the sound change for emphasis. The sound continues for 90 seconds. Once the buzzer begins to sound, it will continue until the rear seat belt is buckled or the ignition switch is turned off.