Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM › 2013.08–2017.10
RM30M0E _57 Power Source / Network _017152 NETWORKING _0084783 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B2785  Communication Malfunction between ECUs Connected by LIN  


DESCRIPTION

The certification ECU (smart key ECU assembly) monitors communication between all the ECUs connected to the certification bus lines. When the certification ECU (smart key ECU assembly) detects errors in communication with all the ECUs connected to the certification bus lines at a set interval and 3 times in a row, DTC B2785 will be stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2785 Communication Malfunction between ECUs Connected by LIN
·

Errors in LIN communication between ECUs or an open or short in communication lines

·

LIN communication error detected by the certification ECU (smart key ECU assembly) 3 times in a row.


·

Certification ECU (smart key ECU assembly)

·

Steering lock ECU (steering lock actuator assembly)

·

Wire harness or connector

·

STRG LOCK fuse



WIRING DIAGRAM

B325121E10
0.375,1.479 0.833,1.677 0.458,0.198 10 false F43 0.375,1.625 2.281,1.938 1.906,0.313 10 false Certification ECU (Smart Key ECU Assembly) 3.24,1.625 5.01,2.031 1.771,0.406 10 false Steering Lock ECU (Steering Lock Actuator Assembly) 3.25,1.479 3.708,1.677 0.458,0.198 10 false F15 1.688,0.969 2.146,1.167 0.458,0.198 10 false LIN 3.271,0.969 3.729,1.167 0.458,0.198 10 false LIN 1.969,0.76 2.177,0.938 0.208,0.177 10 false 5 4.438,1.156 4.896,1.354 0.458,0.198 10 false GND 4.844,0.708 5.052,0.885 0.208,0.177 10 false 7 4.823,1.031 5.031,1.208 0.208,0.177 10 false 1 5.115,0.979 6.104,1.188 0.99,0.208 10 false STRG LOCK 6.167,0.792 7.156,1 0.99,0.208 10 false from Battery 0.688,2.448 2.656,2.646 1.969,0.198 10 false : LIN Communication Line 3.146,0.771 3.354,0.948 0.208,0.177 10 false 5 4.604,0.802 4.813,0.979 0.208,0.177 10 false B

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

If the certification ECU (smart key ECU assembly) is replaced, register the keys (refer to Service Bulletin).

·

If the steering lock ECU (steering lock actuator assembly) is replaced, register the ECU code (refer to Service Bulletin).

·

If the ID code box (immobiliser code ECU) is replaced, register the ECU code and ECU communication ID (refer to Service Bulletin).

·

Before performing the inspection, check that DTC B2786, B2789 is not output.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - EACH ECU)
a.

Disconnect the F43 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the F15 steering lock ECU (steering lock actuator assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F43-5 (LIN) - F15-5 (LIN) Always Below 1 Ω
F43-5 (LIN) - Body ground Always 10 kΩ or higher
F15-5 (LIN) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK DTC OUTPUT (STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK DTC OUTPUT (STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY))
a.

Reconnect the F43 certification ECU (smart key ECU assembly) connector.


b.

Clear the DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Clear DTCs
50002 125

c.

Recheck for DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Trouble Codes
50001 125

Result:
Result Proceed to
DTC B2785 is output A
DTC B2785 is not output B



A

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)