Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO & VISUAL SYSTEM › 2013.08–2017.10
RM30M0E _56 Audio / Visual / Telematics _017106 AUDIO / VIDEO _0084785 AUDIO & VISUAL SYSTEM J

AUDIO / VIDEO  AUDIO & VISUAL SYSTEM  Radio Broadcast cannot be Received or Poor Reception  


PROCEDURE

1.CHECK RADIO RECEIVER ASSEMBLY
a.

Check the radio automatic station search function.

i.

Check the radio automatic station search function by activating it.

Result:
Result Proceed to
Automatic station search function does not stop A
Automatic station search function stops on a station B





A

2.CHECK OPTIONAL COMPONENTS

B

REPLACE RADIO RECEIVER ASSEMBLY

2.CHECK OPTIONAL COMPONENTS
a.

Check if any optional components that may decrease reception capacity, such as sunshade film, are installed.

Result:
Result Proceed to
Optional components are not installed A
Optional components are installed B


NOTICE:

Do not remove optional components without the permission of the customer.




A

3.CHECK RADIO RECEIVER ASSEMBLY

B

REMOVE OPTIONAL COMPONENTS AND CHECK AGAIN (SEE NOTICE ABOVE)

3.CHECK RADIO RECEIVER ASSEMBLY
a.
E187251

Preparation for check

i.

Remove the antenna connector from the radio receiver assembly.



b.

Check for noise

i.

Turn the ignition switch to ACC with the radio receiver assembly connector connected.


ii.

Turn the radio on and tune into AM mode.


iii.

Place a screwdriver, thin wire or other metal object on the radio receiver assembly antenna jack and check that noise can be heard from the speakers.

OK:

Noise occurs.




Result:
Proceed to
OK
NG



OK

4.CHECK RADIO ANTENNA

NG

REPLACE RADIO RECEIVER ASSEMBLY

4.CHECK RADIO ANTENNA
a.

Preparation for check

i.

Remove the roof antenna pole sub-assembly from the amplifier antenna assembly.



b.

Check for noise

i.

Turn the ignition switch to ACC with the radio receiver assembly connector connected.


ii.

Turn the radio on and tune into AM mode.


iii.

Place a screwdriver, thin wire, or other metal object on the amplifier antenna assembly threaded installation portion for the roof antenna pole sub-assembly and check that noise can be heard from the speakers.

Result:
Result Proceed to
Noise does not occur A
Noise occurs B





A

5.INSPECT RADIO RECEIVER ASSEMBLY

B

5.INSPECT RADIO RECEIVER ASSEMBLY
a.

Disconnect the radio receiver assembly connector.


b.
E188455C20
0.646,0.99 1.021,1.229 0.375,0.24 1.542,1.094 1.135,1.448 true 0.177,0.104 0.74,0.469 0.563,0.365 10 false *a 0.74,1.031 1.177,1.333 0.438,0.302 10 false RA 0.833,1.479 1.448,1.792 0.615,0.313 10 false ANT+
*a Component without harness connected
(Radio Receiver Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
RA-5 (ANT+) - Body ground Ignition switch ACC
Radio switch on and FM or AM selected
11 to 14 V



Result:
Proceed to
OK
NG



OK

6.REPLACE ANTENNA CORD SUB-ASSEMBLY

NG

REPLACE RADIO RECEIVER ASSEMBLY

6.REPLACE ANTENNA CORD SUB-ASSEMBLY
a.

Replace the antenna cord sub-assembly and check if radio broadcasts can be received normally.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA CORD>REMOVAL

OK:

Radio broadcasts can be received normally.



Result:
Proceed to
OK
NG



OK

NORMAL OPERATION

NG

7.CHECK NO. 2 ANTENNA CORD SUB-ASSEMBLY
7.CHECK NO. 2 ANTENNA CORD SUB-ASSEMBLY
a.

Disconnect the No. 2 antenna cord sub-assembly.


b.

Measure the resistance of the No. 2 antenna cord sub-assembly to check for an open circuit in the No. 2 antenna cord sub-assembly.

Standard Resistance:

Below 1 Ω



c.

Measure the resistance between the No. 2 antenna cord sub-assembly and body ground to check for a short circuit in the No. 2 antenna cord sub-assembly.

Standard Resistance:

10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.REPLACE NO. 1 AMPLIFIER ANTENNA ASSEMBLY

NG

REPLACE NO. 2 ANTENNA CORD SUB-ASSEMBLY

8.REPLACE NO. 1 AMPLIFIER ANTENNA ASSEMBLY
a.

Replace the No. 1 amplifier antenna assembly and check if radio broadcasts can be received normally.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AMPLIFIER ANTENNA(for Sedan)>REMOVAL

OK:

Radio broadcasts can be received normally.



Result:
Proceed to
OK
NG



OK

NORMAL OPERATION

NG

REPLACE RADIO RECEIVER ASSEMBLY