Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO & VISUAL SYSTEM › 2013.08–2016.10
RM30M0E _56 Audio / Visual / Telematics _017106 AUDIO / VIDEO _0084785 AUDIO & VISUAL SYSTEM J

AUDIO / VIDEO  AUDIO & VISUAL SYSTEM  Radio Receiver Power Source Circuit  


DESCRIPTION

This is the power source circuit to operate the radio receiver assembly.

WIRING DIAGRAM

B287558
0.531,0.667 2.396,1.052 1.865,0.385 10 false from SFT LOCK-ACC Fuse*1 or ECU-ACC Fuse*2 1.625,1.417 4.833,1.615 3.208,0.198 10 false from Battery 3.948,0.823 7.156,1.021 3.208,0.198 10 false ECU-ACC 4.042,1.625 5.26,1.854 1.219,0.229 10 false RADIO 5.802,0.563 6.51,0.75 0.708,0.188 10 false 3 5.802,1.333 6.51,1.521 0.708,0.188 10 false 4 6,0.656 6.708,0.844 0.708,0.188 10 false ACC1 5.979,1.448 6.688,1.635 0.708,0.188 10 false +B1 5.802,2.135 6.51,2.323 0.708,0.188 10 false 7 5.531,2.865 6.24,3.052 0.708,0.188 10 false F1 5.979,2.25 6.688,2.438 0.708,0.188 10 false GND1 5.531,3.052 7.135,3.313 1.604,0.26 10 false Radio Receiver Assembly 0.063,3.063 1.823,3.25 1.76,0.188 10 false *1: for Automatic Transaxle 0.063,3.375 1.823,3.563 1.76,0.188 10 false *2: for Manual Transaxle

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - BATTERY, BODY GROUND)
a.
E259248C15
1.51,0.396 1.896,0.594 0.385,0.198 2.271,1.656 2.083,1.354 true 1.271,1.646 1.594,1.365 true 2.542,1.073 2.135,1.073 true 2.292,0.656 1.938,1.01 true 0.146,0.115 0.458,0.271 0.313,0.156 10 false *a 1.604,0.406 1.948,0.615 0.344,0.208 10 false F1 2.198,1.708 2.75,1.927 0.552,0.219 10 false ILL+ 1.063,1.677 1.5,1.875 0.438,0.198 10 false GND1 2.615,0.969 3.167,1.188 0.552,0.219 10 false +B1 2.375,0.521 2.927,0.74 0.552,0.219 10 false ACC1

Disconnect the radio receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F1-7 (GND1) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F1-4 (+B1) -F1-7 (GND1) Always 11 to 14 V
F1-3 (ACC1) - F1-7 (GND1) Ignition switch ACC 11 to 14 V



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR