Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2013.08–2016.04
RM30M0E _57 Power Source / Network _017152 NETWORKING _0084784 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Open in CAN Main Bus Line (RHD Models)  


DESCRIPTION

There may be an open circuit in one of the V bus main lines and/or a DLC3 branch line when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is 70 Ω or higher.

Symptom Trouble Area
Resistance between terminals 6 (CANH) and 14 (CANL) of DLC3 is 70 Ω or higher.
·

DLC3 branch line or connector

·

CAN main bus line or connector

·

ECM

·

Combination meter assembly

·

No. 2 junction connector

·

No. 1 CAN junction connector



This malfunction is not related to the lines of a CAN main bus branch or to ECUs or sensors connected to a CAN main bus branch.

WIRING DIAGRAM

E271698E04
0.083,0.083 1.333,0.375 1.25,0.292 10 false V Bus: 3.375,0.271 4.146,0.469 0.771,0.198 10 false 120 Ω 4.51,0.24 5.281,0.438 0.771,0.198 10 false F38 4.521,0.396 6.708,0.594 2.188,0.198 10 false Combination Meter Assembly 2.656,0.865 3.229,1.156 0.573,0.292 10 false CANL 3.99,0.865 4.563,1.156 0.573,0.292 10 false CANH 2.885,1.104 3.167,1.344 0.281,0.24 10 false 31 3.979,1.115 4.26,1.354 0.281,0.24 10 false 32 4.01,1.5 4.292,1.74 0.281,0.24 10 false G 2.875,1.479 3.156,1.719 0.281,0.24 10 false W 3.969,1.844 4.25,2.083 0.281,0.24 10 false 1 2.875,1.854 3.156,2.094 0.281,0.24 10 false 12 4.271,2.063 5.042,2.26 0.771,0.198 10 false F71 4.271,2.219 6.458,2.417 2.188,0.198 10 false No. 2 Junction Connector 2.854,3.052 3.135,3.292 0.281,0.24 10 false 13 3.969,3.052 4.25,3.292 0.281,0.24 10 false 2 4.021,3.375 4.302,3.615 0.281,0.24 10 false L 2.854,3.75 3.135,3.99 0.281,0.24 10 false 13 3.979,3.74 4.26,3.979 0.281,0.24 10 false 2 4.885,3.979 5.323,4.26 0.438,0.281 10 false GR 4.885,4.781 5.167,5.021 0.281,0.24 10 false W 4.26,4.042 4.51,4.292 0.25,0.25 10 false 1 4.25,4.698 4.531,4.938 0.281,0.24 10 false 12 5.552,4.042 5.833,4.281 0.281,0.24 10 false 6 5.594,4.698 5.875,4.938 0.281,0.24 10 false 14 5.969,4.802 6.74,5 0.771,0.198 10 false F16 5.958,4.979 6.75,5.24 0.792,0.26 10 false DLC3 5.875,4.552 6.448,4.844 0.573,0.292 10 false CANL 5.74,4.198 6.313,4.49 0.573,0.292 10 false CANH 2.854,4.969 3.135,5.208 0.281,0.24 10 false 14 3.979,4.958 4.198,5.177 0.219,0.219 10 false 3 2.865,3.385 3.146,3.625 0.281,0.24 10 false W 2.875,5.208 3.156,5.448 0.281,0.24 10 false W 4,5.188 4.438,5.469 0.438,0.281 10 false BE 2.76,5.5 3.042,5.74 0.281,0.24 10 false 34 3.552,5.51 3.833,5.75 0.281,0.24 10 false 33 2.813,5.677 3.094,5.917 0.281,0.24 10 false 7 3.625,5.688 3.906,5.927 0.281,0.24 10 false 8 3.323,5.51 3.604,5.75 0.281,0.24 10 false *2 3.323,5.677 3.573,5.938 0.25,0.26 10 false *1 4.083,5.5 4.333,5.76 0.25,0.26 10 false *2 4.083,5.677 4.333,5.938 0.25,0.26 10 false *1 3.771,5.5 4.083,5.708 0.313,0.208 10 false F82 3.021,5.5 3.333,5.708 0.313,0.208 10 false F82 3.01,5.688 3.323,5.896 0.313,0.208 10 false F81 3.771,5.688 4.083,5.896 0.313,0.208 10 false F81 3.354,6.521 4.125,6.719 0.771,0.198 10 false 120 Ω 2.625,5.906 3.198,6.198 0.573,0.292 10 false CANL 3.969,5.927 4.542,6.219 0.573,0.292 10 false CANH 4.531,6.156 5.323,6.417 0.792,0.26 10 false ECM 0.844,4.063 1.615,4.26 0.771,0.198 10 false F62 0.844,4.219 3.031,4.417 2.188,0.198 10 false No. 1 CAN Junction Connector 0.198,6 2.385,6.198 2.188,0.198 10 false *1: for Manual Transaxle 0.188,6.292 2.375,6.49 2.188,0.198 10 false *2: for Automatic Transaxle 0.208,6.615 2.396,6.813 2.188,0.198 10 false x: Suspected Area 0.719,7 2.906,7.198 2.188,0.198 10 false : CAN Main Bus Line (CANH) 0.729,7.406 2.917,7.604 2.188,0.198 10 false : CAN Main Bus Line (CANL) 3.844,6.979 6.031,7.177 2.188,0.198 10 false : CAN Branch Line (CANH) 3.875,7.375 6.063,7.573 2.188,0.198 10 false : CAN Branch Line (CANL)

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the ignition switch to ON and wait at least 60 seconds, and then drive the vehicle at a speed of 20 km/h (12 mph) or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (DLC3 BRANCH LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
C152423C11
1.427,0.167 1.854,0.427 0.427,0.26 1.938,0.927 2.354,0.417 true 1.938,1.438 1.49,1.844 true 0.073,0.083 0.385,0.24 0.313,0.156 10 false *1 1.51,0.198 1.969,0.396 0.458,0.198 10 false F16 2.417,0.292 3.031,0.49 0.615,0.198 10 false CANH 1.094,1.792 1.708,1.99 0.615,0.198 10 false CANL
*1 DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F16-6 (CANH) - F16-14 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


NOTICE:

When the measured value is 133 Ω or higher and a CAN communication system DTC is output, there may be a fault besides disconnection of the DLC3 branch line. For that reason, troubleshooting should be performed again from How to Proceed with Troubleshooting after repairing the trouble area.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING



Result:
Proceed to
OK
NG



OK

2.CHECK FOR OPEN IN CAN BUS LINES (COMBINATION METER ASSEMBLY - NO. 2 JUNCTION CONNECTOR)

NG

REPAIR OR REPLACE CAN BRANCH LINE CONNECTED TO DLC3

2.CHECK FOR OPEN IN CAN BUS LINES (COMBINATION METER ASSEMBLY - NO. 2 JUNCTION CONNECTOR)
a.
C263368C40
1.542,0.427 1.906,0.646 0.365,0.219 1.74,2.406 1.479,2.719 true 1.865,2.417 2.135,2.74 true 0.083,0.073 0.438,0.333 0.354,0.26 10 false *a 1.604,0.469 1.917,0.667 0.313,0.198 10 false F38 1.25,2.76 1.677,2.979 0.427,0.219 10 false CANL 1.969,2.771 2.396,2.99 0.427,0.219 10 false CANH
*a Front view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F38-32 (CANH) - F38-31 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result Proceed to
OK A
NG (for Manual Transaxle) B
NG (for Automatic Transaxle) C



A

REPLACE COMBINATION METER ASSEMBLY

B

3.CHECK FOR OPEN IN CAN BUS LINES (ECM - NO. 1 CAN JUNCTION CONNECTOR)

C

6.CHECK FOR OPEN IN CAN BUS LINES (ECM - NO. 1 CAN JUNCTION CONNECTOR)
3.CHECK FOR OPEN IN CAN BUS LINES (ECM - NO. 1 CAN JUNCTION CONNECTOR)
a.

Reconnect the F38 combination meter assembly connector.


b.
E271714C04
1.542,0.417 1.969,0.667 0.427,0.25 1.677,2.781 2.021,1.688 true 2.188,1.698 2.469,2.76 true 0.125,0.094 0.438,0.292 0.313,0.198 10 false *a 1.635,0.458 2.094,0.656 0.458,0.198 10 false F81 2.302,2.823 2.917,3.021 0.615,0.198 10 false CANH 1.5,2.833 2.115,3.031 0.615,0.198 10 false CANL
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F81-8 (CANH) - F81-7 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

4.CHECK FOR OPEN IN CAN BUS LINES (JUNCTION CONNECTOR)
4.CHECK FOR OPEN IN CAN BUS LINES (JUNCTION CONNECTOR)
a.

Reconnect the F81*1 or F82*2 ECM connector.

*1: for Manual Transaxle

*2: for Automatic Transaxle



b.
C290986C02
1.427,0.667 1.906,0.927 0.479,0.26 1.125,1.74 0.667,1.156 true 0.979,1.74 0.667,1.458 true 0.99,2.042 0.698,2.354 true 1.135,2.042 0.688,2.667 true 0.208,0.219 0.521,0.375 0.313,0.156 10 false *a 0.135,1.063 0.781,1.25 0.646,0.188 10 false CANH*c 1.552,0.708 1.875,0.896 0.323,0.188 10 false F71 0.135,1.365 0.781,1.552 0.646,0.188 10 false CANH*b 0.167,2.271 0.813,2.458 0.646,0.188 10 false CANL*b 0.177,2.594 0.823,2.781 0.646,0.188 10 false CANL*c
*a Front view of wire harness connector
(to No. 2 Junction Connector)
*b to Combination Meter Assembly
*c to No. 1 CAN Junction Connector


Disconnect the No. 2 junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F71-1 (CANH) - F71-12 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Combination meter assembly
F71-2 (CANH) - F71-13 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 1 CAN junction connector



Result:
Result Proceed to
OK A
NG (Combination meter assembly main line) B
NG (No. 1 CAN junction connector main line) C



A

REPLACE NO. 2 JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (COMBINATION METER ASSEMBLY - NO. 2 JUNCTION CONNECTOR)

C

5.CHECK FOR OPEN IN CAN BUS LINES (NO. 1 CAN JUNCTION CONNECTOR)
5.CHECK FOR OPEN IN CAN BUS LINES (NO. 1 CAN JUNCTION CONNECTOR)
a.

Reconnect the F71 No. 2 junction connector.


b.
C290986C03
1.427,0.667 1.906,0.927 0.479,0.26 1.271,1.74 0.667,1.156 true 1.135,1.729 0.667,1.458 true 1.135,2.031 0.698,2.354 true 1.281,2.042 0.688,2.667 true 0.208,0.219 0.521,0.375 0.313,0.156 10 false *a 0.135,1.063 0.781,1.25 0.646,0.188 10 false CANH*c 1.552,0.708 1.875,0.896 0.323,0.188 10 false F62 0.135,1.365 0.781,1.552 0.646,0.188 10 false CANH*b 0.167,2.271 0.813,2.458 0.646,0.188 10 false CANL*b 0.177,2.594 0.823,2.781 0.646,0.188 10 false CANL*c
*a Front view of wire harness connector
(to No. 1 Junction Connector)
*b to No. 2 Junction Connector
*c to ECM


Disconnect the No. 1 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F62-2 (CANH) - F62-13 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 2 junction connector
F62-3 (CANH) - F62-14 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω ECM



Result:
Result Proceed to
OK A
NG (Junction connector main line) B
NG (ECM main line) C



A

REPLACE NO. 1 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 2 JUNCTION CONNECTOR - NO. 1 CAN JUNCTION CONNECTOR)

C

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (ECM - NO. 1 CAN JUNCTION CONNECTOR)

6.CHECK FOR OPEN IN CAN BUS LINES (ECM - NO. 1 CAN JUNCTION CONNECTOR)
a.

Reconnect the F38 combination meter assembly connector.


b.
E271715C18
1.49,0.5 1.896,0.75 0.406,0.25 2.271,2.26 2,2.896 true 2.458,2.271 2.75,2.896 true 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 1.573,0.542 2.031,0.74 0.458,0.198 10 false F82 1.781,2.917 2.396,3.115 0.615,0.198 10 false CANH 2.604,2.917 3.219,3.115 0.615,0.198 10 false CANL
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F82-33 (CANH) - F82-34 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

4.CHECK FOR OPEN IN CAN BUS LINES (JUNCTION CONNECTOR)