Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2013.08–2014.03
RM30M0E _57 Power Source / Network _017152 NETWORKING _0084784 CAN COMMUNICATION SYSTEM U

NETWORKING  CAN COMMUNICATION SYSTEM  TERMINALS OF ECU  


NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Turn the ignition switch off before inspecting CAN bus lines for a ground short.

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

This section describes the standard values for all CAN related components.



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



NO. 1 CAN JUNCTION CONNECTOR (for LHD)


a.

Check the No. 1 CAN junction connector.

i.
C287147C03
1.531,0.156 1.906,0.344 0.375,0.188 0.615,0.854 1.406,1.74 true 0.625,1.052 1.25,1.729 true 0.625,1.302 1.115,1.729 true 0.625,1.833 0.948,1.833 true 0.635,2 0.958,2 true 1.125,2.052 0.615,2.375 true 1.281,2.052 0.604,2.667 true 1.417,2.052 0.604,2.927 true 1.74,2.042 2.677,2.729 true 1.708,1.729 2.677,0.896 true 1.885,1.719 2.719,1.271 true 2.031,1.719 2.677,1.469 true 2.031,2.031 2.698,2.313 true 1.854,2.052 2.698,2.5 true 0.083,0.719 1,0.917 0.917,0.198 10 false CANH*e 0.083,0.969 1,1.167 0.917,0.198 10 false CANH*d 0.083,1.219 1,1.417 0.917,0.198 10 false CANH*c 0.083,1.719 1,1.917 0.917,0.198 10 false CANH*b 0.083,1.969 1,2.167 0.917,0.198 10 false CANL*b 0.083,2.302 1,2.5 0.917,0.198 10 false CANL*c 0.083,2.583 1,2.781 0.917,0.198 10 false CANL*d 0.083,2.833 1,3.031 0.917,0.198 10 false CANL*e 2.75,2.667 3.333,2.833 0.583,0.167 10 false CANL*f 2.74,0.802 3.323,1 0.583,0.198 10 false CANH*f 1.594,0.167 2.052,0.365 0.458,0.198 10 false F62 0.042,0.042 0.354,0.24 0.313,0.198 10 false *a 2.75,1.167 3.333,1.365 0.583,0.198 10 false CANH*g 2.729,1.375 3.313,1.573 0.583,0.198 10 false CANH*h 2.75,2.417 3.333,2.615 0.583,0.198 10 false CANL*g 2.75,2.219 3.333,2.417 0.583,0.198 10 false CANL*h
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b to DLC3
*c to Brake Actuator Assembly*1
*d to ECM
*e to Airbag ECU Assembly*2
*f to Combination Meter Assembly
*g to Certification ECU (Smart Key ECU Assembly)*3
*h to Air Conditioning Amplifier Assembly*4


Connection diagram


ii.

Check the connection diagram of the components which are connected to the No. 1 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
F62-1 (CANH) GR DLC3
F62-12 (CANL) W
F62-2 (CANH) L Brake actuator assembly*1
F62-13 (CANL) W
F62-3 (CANH) BE ECM
F62-14 (CANL) W
F62-4 (CANH) B Airbag ECU assembly*2
F62-15 (CANL) W
F62-6 (CANH) G Combination meter assembly
F62-17 (CANL) W
F62-7 (CANH) L Certification ECU (smart Key ECU assembly)*3
F62-18 (CANL) W
F62-8 (CANH) V Air conditioning amplifier assembly*4
F62-19 (CANL) W

*1: w/ ABS

*2: w/ Airbag System

*3: w/ Smart Entry and Start System

*4: for Automatic Air Conditioning System





NO. 2 JUNCTION CONNECTOR (for RHD)


a.

Check the No. 2 junction connector.

i.

Connection diagram

E277252C04
1.781,0.656 2.198,0.917 0.417,0.26 4.958,0.656 5.375,0.917 0.417,0.26 2.583,1.427 2.917,1.083 true 2.594,1.656 2.917,1.917 true 4.594,1.458 4.25,1.417 true 4.583,1.615 4.25,1.75 true 4.729,1.417 4.333,0.917 true 4.729,1.646 4.333,2.167 true 0.146,0.104 0.458,0.302 0.313,0.198 10 false *a 2.958,1 3.573,1.198 0.615,0.198 10 false CANH*b 2.948,1.865 3.563,2.063 0.615,0.198 10 false CANL*b 3.719,1.313 4.333,1.51 0.615,0.198 10 false CANH*c 3.729,1.667 4.344,1.865 0.615,0.198 10 false CANL*c 3.792,0.833 4.406,1.031 0.615,0.198 10 false CANH*d 3.802,2.094 4.417,2.292 0.615,0.198 10 false CANL*d 1.875,0.708 2.333,0.906 0.458,0.198 10 false A34 5.052,0.698 5.51,0.896 0.458,0.198 10 false F71
*a Front view of wire harness connector
(to No. 2 Junction Connector)
*b to Brake Actuator Assembly
*c to Combination Meter Assembly *d to No. 1 CAN Junction Connector



ii.

Check the connection diagram of the components which are connected to the No. 2 junction connector.

Terminal No. (Symbol) Wiring Color Connected to
A34-11 (CANH) L Brake actuator assembly
A34-22 (CANL) W
F71-1 (CANH) G Combination meter assembly
F71-12 (CANL) W
F71-2 (CANH) L No. 1 CAN junction connector
F71-13 (CANL) W




NO. 1 CAN JUNCTION CONNECTOR (for RHD)


a.

Check the No. 1 CAN junction connector.

i.

Connection diagram

E277253C07
3.333,0.656 3.75,0.917 0.417,0.26 2.948,1.458 2.583,1.417 true 2.948,1.625 2.583,1.667 true 3.083,1.427 2.583,1.083 true 3.083,1.646 2.583,2 true 3.198,1.427 2.583,0.833 true 3.198,1.646 2.583,2.25 true 3.313,1.427 2.583,0.583 true 3.323,1.646 2.583,2.5 true 3.677,1.427 4.583,0.917 true 3.677,1.646 4.583,2.25 true 0.24,0.146 0.552,0.344 0.313,0.198 10 false *a 2.052,1.333 2.969,1.531 0.917,0.198 10 false CANH*b 2.052,1.594 2.969,1.792 0.917,0.198 10 false CANL*b 2.052,1 2.969,1.198 0.917,0.198 10 false CANH*c 2.052,0.729 2.969,0.927 0.917,0.198 10 false CANH*d 2.052,0.49 2.969,0.688 0.917,0.198 10 false CANH*e 2.052,1.927 2.969,2.125 0.917,0.198 10 false CANL*c 2.052,2.177 2.969,2.375 0.917,0.198 10 false CANL*d 2.052,2.448 2.969,2.646 0.917,0.198 10 false CANL*e 4.646,0.823 5.563,1.021 0.917,0.198 10 false CANH*g 4.646,2.167 5.563,2.365 0.917,0.198 10 false CANL*g 3.438,0.708 3.896,0.906 0.458,0.198 10 false F62
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b to DLC3
*c to No. 2 Junction Connector *d to ECM
*e to Airbag ECU Assembly *f to Certification ECU (Smart Key ECU Assembly)*1



ii.

Check the connection diagram of the components which are connected to the No. 1 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
F62-1 (CANH) GR DLC3
F62-12 (CANL) W
F62-2 (CANH) L No. 2 junction connector
F62-13 (CANL) W
F62-3 (CANH) BE ECM
F62-14 (CANL) W
F62-4 (CANH) B Airbag ECU assembly
F62-15 (CANL) W
F62-7 (CANH) L Certification ECU (smart key ECU assembly)*1
F62-18 (CANL) W

*1: w/ Smart Entry and Start System





DLC3


a.

Disconnect the cable from the negative (-) battery terminal.

E277254C06
3.448,0.573 3.865,0.823 0.417,0.25 3.542,1.188 2.917,0.75 true 3.833,1.188 4.333,0.75 true 4.156,1.615 4.583,2.083 true 3.854,1.615 3.333,2.083 true 0.208,0.135 0.521,0.333 0.313,0.198 10 false *1 2.677,0.677 2.99,0.875 0.313,0.198 10 false CG 4.375,0.667 4.99,0.865 0.615,0.198 10 false CANH 4.635,2.01 5.094,2.208 0.458,0.198 10 false BAT 2.948,2 3.563,2.198 0.615,0.198 10 false CANL 3.542,0.615 4,0.813 0.458,0.198 10 false F16
*1 DLC3 - -



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F16-6 (CANH) - F16-14 (CANL) GR - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
F16-6 (CANH) - F16-4 (CG) GR - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F16-14 (CANL) - F16-4 (CG) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F16-6 (CANH) - F16-16 (BAT) GR - B HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
F16-14 (CANL) - F16-16 (BAT) W - B LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




ECM (for Automatic Transaxle)


E277255C05
1.344,0.583 1.76,0.833 0.417,0.25 2.688,0.583 3.104,0.833 0.417,0.25 4.198,0.583 4.615,0.833 0.417,0.25 5.469,0.583 5.885,0.833 0.417,0.25 0.177,0.115 0.49,0.313 0.313,0.198 10 false *a 1.448,0.635 1.906,0.833 0.458,0.198 10 false B29 2.792,0.635 3.25,0.833 0.458,0.198 10 false B31 4.292,0.635 4.75,0.833 0.458,0.198 10 false F82 5.563,0.635 6.021,0.833 0.458,0.198 10 false F83
*a Component without harness connected
(ECM)
- -


a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the ECM connectors.

E271710C03
1.135,0.344 1.552,0.594 0.417,0.25 3.365,0.365 3.781,0.615 0.417,0.25 5.708,0.396 6.125,0.646 0.417,0.25 4.208,1.833 4.385,2.323 true 4.063,1.844 3.833,2.333 true 0.75,1.302 0.448,2.271 true 5.906,1.292 6.188,2.344 true 0.146,0.104 0.458,0.302 0.313,0.198 10 false *a 1.219,0.385 1.677,0.583 0.458,0.198 10 false B29 3.469,0.406 3.927,0.604 0.458,0.198 10 false F82 5.792,0.438 6.25,0.635 0.458,0.198 10 false F83 3.604,2.365 4.219,2.563 0.615,0.198 10 false CANH 4.219,2.365 4.833,2.563 0.615,0.198 10 false CANL 0.365,2.313 0.979,2.51 0.615,0.198 10 false E1 6.031,2.396 6.646,2.594 0.615,0.198 10 false BATT
*a Front view of wire harness connector
(to ECM)
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F82-33 (CANH) - F82-34 (CANL) BE - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 108 to 132 Ω
F82-33 (CANH) - B29-1 (E1) BE - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F82-34 (CANL) - B29-1 (E1) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F82-33 (CANH) - F83-4 (BATT) BE - G HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
F82-34 (CANL) - F83-4 (BATT) W - G LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




ECM (for Manual Transaxle)


A295438C03
1.99,0.719 2.375,0.969 0.385,0.25 3.375,0.729 3.76,0.979 0.385,0.25 4.781,0.75 5.167,1 0.385,0.25 2.073,0.771 2.531,0.969 0.458,0.198 10 false F81 3.448,0.771 3.906,0.969 0.458,0.198 10 false B30 4.854,0.792 5.313,0.99 0.458,0.198 10 false B32 0.115,0.104 0.427,0.302 0.313,0.198 10 false *a
*a Component without harness connected
(ECM)
- -


a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the ECM connector.

E271711C02
1.958,0.333 2.396,0.615 0.438,0.281 4.958,0.344 5.396,0.625 0.438,0.281 2.542,1.417 2.083,2.333 true 2.396,1.406 1.542,2.323 true 2.667,1.406 2.563,2.323 true 4.615,1.333 4.198,2.313 true 0.104,0.094 0.417,0.25 0.313,0.156 10 false *a 2.052,0.396 2.51,0.594 0.458,0.198 10 false F81 5.073,0.406 5.531,0.604 0.458,0.198 10 false B32 1.865,2.375 2.479,2.573 0.615,0.198 10 false CANH 1.354,2.365 1.969,2.563 0.615,0.198 10 false CANL 2.406,2.375 3.021,2.573 0.615,0.198 10 false BATT 4.125,2.344 4.74,2.542 0.615,0.198 10 false E1
*a Front view of wire harness connector
(to ECM)
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F81-8 (CANH) - F81-7 (CANL) BE - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
F81-8 (CANH) - B32-1 (E1) BE - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F81-7 (CANL) - B32-1 (E1) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F81-8 (CANH) - F81-9 (BATT) BE - G HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
F81-7 (CANL) - F81-9 (BATT) W - G LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




BRAKE ACTUATOR ASSEMBLY (w/ ABS)


C160258C12
3.26,0.74 3.76,0.99 0.5,0.25 0.438,0.302 0.646,0.5 0.208,0.198 10 false *a 3.385,0.792 4,0.99 0.615,0.198 10 false A35
*a Component without harness connected
(Brake Actuator Assembly)
- -


a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the brake actuator assembly connector.

E277245C04
3.448,0.417 3.865,0.667 0.417,0.25 3.115,1.292 2.313,2.167 true 3.344,1.406 2.948,2.167 true 3.354,1.479 3.469,2.177 true 4.156,1.292 3.979,2.167 true 0.156,0.135 0.469,0.333 0.313,0.198 10 false *a 2.094,2.219 2.708,2.417 0.615,0.198 10 false GND1 2.76,2.219 3.167,2.417 0.406,0.198 10 false CANL 3.281,2.219 3.75,2.417 0.469,0.198 10 false CANH 3.833,2.219 4.302,2.417 0.469,0.198 10 false +BS 3.552,0.458 4.01,0.656 0.458,0.198 10 false A35
*a Front view of wire harness connector
(to Brake Actuator Assembly)
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A35-25 (CANH) - A35-14 (CANL) L - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
A35-25 (CANH) - A35-1 (GND1) L - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A35-14 (CANL) - A35-1 (GND1) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A35-25 (CANH) - A35-12 (+BS) L - W HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A35-14 (CANL) - A35-12 (+BS) W - W LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




AIRBAG ECU ASSEMBLY (w/ Airbag System)


C281391C02
2.802,0.75 3.25,0.917 0.448,0.167 4.167,0.75 4.583,0.917 0.417,0.167 2.896,0.75 3.229,1 0.333,0.25 10 false F21 4.26,0.75 4.594,1 0.333,0.25 10 false F22 0.115,0.063 0.427,0.219 0.313,0.156 10 false *a
*a Component without harness connected
(Airbag ECU Assembly)
- -


a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the airbag ECU assembly connector.

C188802C18
1.552,0.604 1.927,0.813 0.375,0.208 4.927,0.542 5.302,0.75 0.375,0.208 1.229,1.135 1.521,1.615 true 1.417,1.885 1.208,2.354 true 5.719,1.969 5.938,2.313 true 1.698,1.896 1.688,2.354 true 0.188,0.156 0.635,0.563 0.448,0.406 10 false *a 1,2.385 1.573,2.625 0.573,0.24 10 false CANL 0.823,1.063 1.406,1.396 0.583,0.333 10 false CANH 1.615,2.396 2.021,2.688 0.406,0.292 10 false E1 5.854,2.354 6.25,2.552 0.396,0.198 10 false BAT 1.625,0.635 2.125,1.021 0.5,0.385 10 false F21 3.396,0.156 3.875,0.438 0.479,0.281 10 false *1 5.021,0.573 5.406,0.885 0.385,0.313 10 false F16
*1 DLC3 - -
*a Front view of wire harness connector
(to Airbag ECU Assembly)
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F21-13 (CANH) - F21-22 (CANL) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
F21-13 (CANH) - F21-25 (E1) B - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F21-22 (CANL) - F21-25 (E1) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F21-13 (CANH) - F16-16 (BAT) B - B HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
F21-22 (CANL) - F16-16 (BAT) W - B LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (w/ Smart Entry and Start System)


B333750C04
2.427,0.333 2.865,0.615 0.438,0.281 4.094,0.354 4.531,0.635 0.438,0.281 2.521,0.396 2.979,0.594 0.458,0.198 10 false F43 4.188,0.406 4.646,0.604 0.458,0.198 10 false F44 0.156,0.115 0.469,0.313 0.313,0.198 10 false *a
*a Component without harness connected
(Certification ECU (Smart Key ECU Assembly))
- -


a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the certification ECU (smart key ECU assembly) connectors.

E277246C04
1.875,0.667 2.292,0.917 0.417,0.25 4.74,0.667 5.156,0.917 0.417,0.25 1.25,1.344 0.875,2.094 true 2.896,1.333 3.083,2.083 true 6.052,1.354 5.375,2.073 true 6.042,1.49 6.26,2.083 true 0.167,0.104 0.479,0.302 0.313,0.198 10 false *a 0.75,2.135 1.063,2.333 0.313,0.198 10 false +B 3.052,2.135 3.365,2.333 0.313,0.198 10 false E 5.177,2.135 5.573,2.333 0.396,0.198 10 false CANL 6.094,2.135 6.583,2.333 0.49,0.198 10 false CANH 1.969,0.708 2.427,0.906 0.458,0.198 10 false F43 4.844,0.708 5.302,0.906 0.458,0.198 10 false F44
*a Front view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly))
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F44-40 (CANH) - F44-18 (CANL) L - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
F44-40 (CANH) - F43-10 (E) L- W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F44-18 (CANL) - F43-10 (E) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F44-40 (CANH) - F43-1 (+B) L - B HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
F44-18 (CANL) - F43-1 (+B) W - B LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




COMBINATION METER ASSEMBLY


E277247C03
2.083,0.583 2.5,0.833 0.417,0.25 5.542,0.583 5.958,0.833 0.417,0.25 0.167,0.115 0.479,0.313 0.313,0.198 10 false *a 2.177,0.625 2.635,0.823 0.458,0.198 10 false F38 5.635,0.625 6.094,0.823 0.458,0.198 10 false F39
*a Component without harness connected
(Combination Meter Assembly)
- -


a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the combination meter assembly connector.

E277248E03
3.375,0.583 3.792,0.833 0.417,0.25 2.677,1.604 2.229,2.188 true 3.625,1.594 3.396,2.188 true 3.719,1.594 3.906,2.167 true 4.479,1.604 4.708,2.188 true 0.167,0.104 0.479,0.302 0.313,0.198 10 false *a 2.115,2.229 2.427,2.427 0.313,0.198 10 false ED 3.188,2.229 3.604,2.427 0.417,0.198 10 false CANL 3.74,2.229 4.156,2.427 0.417,0.198 10 false CANH 4.688,2.229 5.104,2.427 0.417,0.198 10 false B 3.469,0.635 3.927,0.833 0.458,0.198 10 false F38


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F38-32 (CANH) - F38-31 (CANL) G - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 108 to 132 Ω
F38-32 (CANH) - F38-21 (ED) G - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F38-31 (CANL) - F38-21 (ED) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F38-32 (CANH) - F38-40 (B) G - B HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
F38-31 (CANL) - F38-40 (B) W - B LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




AIR CONDITIONING AMPLIFIER ASSEMBLY (for Automatic Air Conditioning System)


E277249C03
2.833,0.5 3.25,0.75 0.417,0.25 4.958,0.5 5.375,0.75 0.417,0.25 0.167,0.135 0.479,0.333 0.313,0.198 10 false *a 2.969,0.542 3.281,0.74 0.313,0.198 10 false F3 5.104,0.542 5.417,0.74 0.313,0.198 10 false z2
*a Component without harness connected
(Combination Meter Assembly)
- -


a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the air conditioning amplifier assembly connector.

E277248C07
3.375,0.583 3.792,0.833 0.417,0.25 2.677,1.604 2.229,2.188 true 3.625,1.5 3.396,2.188 true 3.729,1.49 3.906,2.167 true 3.927,1.5 4.708,2.188 true 0.167,0.104 0.479,0.302 0.313,0.198 10 false *a 2.146,2.229 2.458,2.427 0.313,0.198 10 false B 3.26,2.229 3.677,2.427 0.417,0.198 10 false TX+ 3.813,2.229 4.229,2.427 0.417,0.198 10 false TX- 4.688,2.229 5.104,2.427 0.417,0.198 10 false GND 3.51,0.635 3.969,0.833 0.458,0.198 10 false F3
*a Front view of wire harness connector
(to Air Conditioning Amplifier Assembly)
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F3-11 (TX+) - F3-12 (TX-) V - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
F3-11 (TX+) - F3-14 (GND) V - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F3-12 (TX-) - F3-14 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F3-11 (TX+) - F3-21 (B) V - GR HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
F3-12 (TX-) - F3-21 (B) W - GR LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher