Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2013.08–2014.03
RM30M0E _57 Power Source / Network _017152 NETWORKING _0084784 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Combination Meter ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Combination Meter ECU Communication Stop Mode Either condition is met:
·

"Combination Meter" is not displayed on the CAN Bus Check screen of the GTS

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "Combination Meter ECU Communication Stop Mode" in "DTC Combination Table" are output

Click here(Click here)


·

Combination meter assembly main line or connector

·

Power source circuit of combination meter assembly

·

Combination meter assembly ground circuit

·

Combination meter assembly



WIRING DIAGRAM

E273510E05
3.583,4.698 3.833,5.198 3.833,5.198 4,5.198 false 0.083,0.021 1.625,0.271 1.542,0.25 12 false V Bus (for LHD): 1.281,0.313 3.823,0.531 2.542,0.219 10 false : CAN Main Bus Line (CANH) 1.281,0.656 3.823,0.875 2.542,0.219 10 false : CAN Main Bus Line (CANL) 1.281,1 3.823,1.219 2.542,0.219 10 false : CAN Branch Line (CANH) 1.281,1.344 3.823,1.563 2.542,0.219 10 false : CAN Branch Line (CANL) 3.917,0.333 6.323,0.531 2.406,0.198 10 false *1: for Manual Transaxle 3.917,0.667 6.323,0.865 2.406,0.198 10 false *2: for Automatic Transaxle 0.813,2.417 3.094,2.771 2.281,0.354 10 false from Ignition or Starter Switch Assembly*3 or No. 2 Ignition Relay*4 4.26,2.5 4.875,2.698 0.615,0.198 10 false DLC3 1.469,3.177 1.781,3.375 0.313,0.198 10 false 39 1.427,3.719 1.74,3.917 0.313,0.198 10 false 40 1.458,4.552 1.771,4.75 0.313,0.198 10 false 21 1.708,3.26 2.188,3.469 0.479,0.208 10 false IG+ 1.688,3.802 2.167,4.01 0.479,0.208 10 false B 1.698,4.604 2.177,4.813 0.479,0.208 10 false ED 0.885,3.385 1.656,3.583 0.771,0.198 10 false METER 0.813,3.958 1.583,4.156 0.771,0.198 10 false SECURITY 0.802,4.26 1.573,4.458 0.771,0.198 10 false from Battery 1.313,4.896 1.625,5.094 0.313,0.198 10 false F38 1.302,5.042 3.396,5.26 2.094,0.219 10 false Combination Meter Assembly 1.115,5.5 2.083,5.708 0.969,0.208 10 false Trouble Area 2.219,4.146 2.99,4.344 0.771,0.198 10 false 120 Ω 6.146,4.125 6.917,4.323 0.771,0.198 10 false 120 Ω 4.104,5.281 6.167,5.448 2.063,0.167 10 false No. 1 CAN Junction Connector 4.104,5.125 4.417,5.323 0.313,0.198 10 false F62 5.875,4.75 6.917,4.938 1.042,0.188 10 false F81*1, F82*2 5.885,4.917 6.458,5.104 0.573,0.188 10 false ECM 2.396,3.26 2.865,3.49 0.469,0.229 10 false CANH 2.396,3.875 2.865,4.104 0.469,0.229 10 false CANL 2.844,3.26 3.083,3.427 0.24,0.167 10 false 32 2.844,3.875 3.083,4.042 0.24,0.167 10 false 31 3.917,1 6.417,1.25 2.5,0.25 10 false *3: w/o Smart Entry and Start System 3.917,1.333 6.417,1.583 2.5,0.25 10 false *4: w/ Smart Entry and Start System

E273503E06
3.74,4.708 4.167,5.333 4.167,5.333 4.333,5.333 false 4.708,3.188 3.583,1.75 3.583,1.75 3.417,1.75 false 0.792,4.26 1.604,4.49 0.813,0.229 10 false from Battery 0.813,2.406 3.094,2.781 2.281,0.375 10 false from Ignition or Starter Switch Assembly*3 or No. 2 Ignition Relay*4 0.823,3.958 1.521,4.156 0.698,0.198 10 false SECURITY 0.885,3.385 1.375,3.604 0.49,0.219 10 false METER 1.719,3.813 1.875,4.01 0.156,0.198 10 false B 1.708,3.271 2.167,3.469 0.458,0.198 10 false IG+ 1.719,4.646 2.031,4.844 0.313,0.198 10 false ED 1.469,3.708 1.781,3.906 0.313,0.198 10 false 40 1.469,3.188 1.781,3.385 0.313,0.198 10 false 39 1.49,4.552 1.802,4.75 0.313,0.198 10 false 21 1.25,5.469 2.083,5.667 0.833,0.198 10 false Trouble Area 2.031,4.135 2.552,4.385 0.521,0.25 10 false 120 Ω 6.167,4.115 6.667,4.354 0.5,0.24 10 false 120 Ω 0.073,0.052 1.542,0.281 1.469,0.229 12 false V Bus (for RHD): 1.25,0.313 3.104,0.521 1.854,0.208 10 false : CAN Main Bus Line (CANH) 1.25,0.667 3.104,0.875 1.854,0.208 10 false : CAN Main Bus Line (CANL) 1.25,1.01 2.917,1.24 1.667,0.229 10 false : CAN Branch Line (CANH) 1.25,1.344 2.917,1.583 1.667,0.24 10 false : CAN Branch Line (CANL) 4.167,0.302 5.698,0.5 1.531,0.198 10 false *1: for Manual Transaxle 4.167,0.646 5.938,0.844 1.771,0.198 10 false *2: for Automatic Transaxle 4.167,1 6.646,1.333 2.479,0.333 10 false *3: w/o Smart Entry and Start System 4.865,2.448 5.24,2.615 0.375,0.167 10 false DLC3 5.938,4.729 6.833,4.927 0.896,0.198 10 false F81*1, F82*2 5.927,4.906 6.771,5.104 0.844,0.198 10 false ECM 4.385,5.271 4.688,5.479 0.302,0.208 10 false F71 4.385,5.427 6.385,5.656 2,0.229 10 false No. 2 Junction Connector 1.542,1.677 1.833,1.896 0.292,0.219 10 false F62 1.531,1.854 3.448,2.073 1.917,0.219 10 false No. 1 CAN Junction Connector 1.323,4.865 1.625,5.073 0.302,0.208 10 false F38 1.313,5.021 3.229,5.24 1.917,0.219 10 false Combination Meter Assembly 4.167,1.354 6.51,1.698 2.344,0.344 10 false *4: w/ Smart Entry and Start System 2.396,3.24 2.917,3.49 0.521,0.25 10 false CANH 2.396,3.875 2.917,4.125 0.521,0.25 10 false CANL 2.854,3.24 3.094,3.49 0.24,0.25 10 false 32 2.854,3.875 3.083,4.115 0.229,0.24 10 false 31

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the ignition switch to ON and wait at least 20 seconds.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (COMBINATION METER ASSEMBLY MAIN LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
E221291C18
1.5,0.25 1.917,0.5 0.417,0.25 1.781,1.385 1.552,1.771 true 1.906,1.396 2.104,1.75 true 1.604,0.292 2.083,0.51 0.479,0.219 10 false F38 0.073,0.052 0.281,0.26 0.208,0.208 10 false *a 1.365,1.802 1.792,2.042 0.427,0.24 10 false CANL 1.938,1.792 2.375,2.031 0.438,0.24 10 false CANH
*a Front view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F38-32 (CANH) - F38-31 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (COMBINATION METER ASSEMBLY MAIN LINE)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
E221291C19
1.5,0.25 1.917,0.5 0.417,0.25 0.458,1.406 0.177,1.781 true 2.823,1.406 2.563,1.76 true 2.969,1.406 3.125,1.75 true 1.604,0.292 2.125,0.521 0.521,0.229 10 false F38 0.073,0.052 0.281,0.26 0.208,0.208 10 false *a 0.052,1.802 0.479,2.042 0.427,0.24 10 false ED 2.438,1.792 2.875,2.031 0.438,0.24 10 false IG+ 3.094,1.792 3.333,2.021 0.24,0.229 10 false B
*a Front view of wire harness connector
(to Combination Meter Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F38-21 (ED) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Connect the cable to the negative (-) battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F38-40 (B) - Body ground Always 11 to 14 V
F38-39 (IG+) - Body ground Ignition switch ON 11 to 14 V



Result:
Result
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)