Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM › 2013.08–2017.10
RM30M0E _59 Vehicle Exterior _017121 WINDOW / GLASS _0086434 POWER WINDOW CONTROL SYSTEM J

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  Rear Power Window LH Manual Function does not Operate with Rear Power Window Switch LH  


DESCRIPTION

If the rear LH side manual up/down function does not operate, a malfunction may be present in the rear power window regulator motor assembly LH, rear power window regulator switch assembly LH, power window regulator master switch assembly or wire harness.

WIRING DIAGRAM

E263566
3.25,0.656 3.406,0.854 0.156,0.198 10 false 2 3.25,0.979 3.406,1.177 0.156,0.198 10 false 1 4.844,0.479 5,0.677 0.156,0.198 10 false 4 5.042,0.563 5.198,0.76 0.156,0.198 10 false U 5.042,1.063 5.198,1.26 0.156,0.198 10 false D 4.833,0.958 4.99,1.156 0.156,0.198 10 false 1 4.844,1.531 5,1.729 0.156,0.198 10 false 3 5.042,1.656 5.198,1.854 0.156,0.198 10 false B 4.844,2.906 5,3.104 0.156,0.198 10 false 5 5.042,3.021 5.313,3.219 0.271,0.198 10 false SU 5.042,3.323 5.375,3.521 0.333,0.198 10 false SD 4.844,3.219 5.021,3.427 0.177,0.208 10 false 2 4.979,3.833 5.156,4.042 0.177,0.208 10 false J1 2.219,3.229 2.469,3.438 0.25,0.208 10 false 13 2.219,2.927 2.49,3.135 0.271,0.208 10 false 12 2.021,3.031 2.198,3.24 0.177,0.208 10 false U 2.021,3.979 2.198,4.188 0.177,0.208 10 false E 2.271,3.875 2.448,4.083 0.177,0.208 10 false 1 2.021,3.333 2.198,3.542 0.177,0.208 10 false D 2.25,1.802 2.917,2.021 0.667,0.219 10 false POWER 0.25,1.646 1.146,2.052 0.896,0.406 10 false from POWER Relay 1.083,0.604 1.313,0.792 0.229,0.188 10 false J2 1.073,0.771 2.969,1.25 1.896,0.479 10 false Rear Power Window Regulator Motor Assembly LH 0.438,4.479 0.688,4.677 0.25,0.198 10 false H8 4.979,4 6.865,4.521 1.885,0.521 10 false Rear Power Window Regulator Switch Assembly LH 0.448,4.646 2.104,5.104 1.656,0.458 10 false Power Window Regulator Master Switch Assembly 0.135,0.125 0.875,0.375 0.74,0.25 12 false for LHD:

E263566
3.25,0.656 3.406,0.854 0.156,0.198 10 false 2 3.25,0.979 3.406,1.177 0.156,0.198 10 false 1 4.844,0.479 5,0.677 0.156,0.198 10 false 4 5.042,0.563 5.198,0.76 0.156,0.198 10 false U 5.042,1.063 5.198,1.26 0.156,0.198 10 false D 4.833,0.958 4.99,1.156 0.156,0.198 10 false 1 4.844,1.531 5,1.729 0.156,0.198 10 false 3 5.042,1.656 5.198,1.854 0.156,0.198 10 false B 4.844,2.906 5,3.104 0.156,0.198 10 false 5 5.042,3.021 5.313,3.219 0.271,0.198 10 false SU 5.042,3.323 5.375,3.521 0.333,0.198 10 false SD 4.844,3.219 5.021,3.427 0.177,0.208 10 false 2 4.979,3.833 5.156,4.042 0.177,0.208 10 false J1 2.219,3.229 2.469,3.438 0.25,0.208 10 false 10 2.219,2.927 2.49,3.135 0.271,0.208 10 false 18 2.021,3.031 2.198,3.24 0.177,0.208 10 false U 2.021,3.979 2.198,4.188 0.177,0.208 10 false E 2.271,3.875 2.448,4.083 0.177,0.208 10 false 9 2.021,3.333 2.198,3.542 0.177,0.208 10 false D 2.25,1.802 2.917,2.021 0.667,0.219 10 false POWER 0.271,1.646 1.156,2.042 0.885,0.396 10 false from POWER Relay 1.083,0.604 1.313,0.792 0.229,0.188 10 false J2 1.073,0.771 2.958,1.229 1.885,0.458 10 false Rear Power Window Regulator Motor Assembly LH 0.438,4.469 0.688,4.667 0.25,0.198 10 false G5 4.979,4 6.865,4.406 1.885,0.406 10 false Rear Power Window Regulator Switch Assembly LH 0.448,4.646 2.104,5.104 1.656,0.458 10 false Power Window Regulator Master Switch Assembly 0.135,0.104 0.885,0.354 0.75,0.25 12 false for RHD:

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH
a.

Remove the rear power window regulator switch assembly LH.

Click hereVehicle Exterior>WINDOW / GLASS>REAR POWER WINDOW SWITCH>REMOVAL


b.

Inspect the rear power window regulator switch assembly LH.

Click hereVehicle Exterior>WINDOW / GLASS>REAR POWER WINDOW SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

2.INSPECT REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

NG

REPLACE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH

2.INSPECT REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH
a.

Remove the rear power window regulator motor assembly LH.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR(for Rear Door)>REMOVAL


b.

Inspect the rear power window regulator motor assembly LH.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR(for Rear Door)>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH - POWER RELAY)

NG

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

3.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH - POWER RELAY)
a.
B276367C08
0.188,0.958 0.719,1.25 0.531,0.292 1.75,1.24 1.833,1.698 true 0.354,1.021 0.563,1.198 0.208,0.177 10 false J1 0.094,0 0.313,0.188 0.219,0.188 10 false *a 1.823,1.719 1.99,1.906 0.167,0.188 10 false B
*a Front view of wire harness connector
(to Rear Power Window Regulator Switch Assembly LH)


Disconnect the rear power window regulator switch assembly LH connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
J1-3 (B) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)
a.

Disconnect the J1 rear power window regulator switch assembly LH connector.


b.

Disconnect the J2 rear power window regulator motor assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J1-1 (D) - J2-1 Always Below 1 Ω
J1-4 (U) - J2-2 Always Below 1 Ω
J1-1 (D) or J2-1 - Body ground Always 10 kΩ or higher
J1-4 (U) or J2-2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH)
a.

for LHD

i.

Disconnect the H8 power window regulator master switch assembly connector.


ii.

Disconnect the J1 rear power window regulator switch assembly LH connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H8-12(U) - J1-5 (SU) Always Below 1 Ω
H8-13 (D) - J1-2 (SD) Always Below 1 Ω
H8-12 (U) or J1-5 (SU) - Body ground Always 10 kΩ or higher
H8-13 (D) or J1-2 (SD) - Body ground Always 10 kΩ or higher




b.

for RHD

i.

Disconnect the G5 power window regulator master switch assembly connector.


ii.

Disconnect the J1 rear power window regulator switch assembly LH connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G5-18(U) - J1-5 (SU) Always Below 1 Ω
G5-10 (D) - J1-2 (SD) Always Below 1 Ω
G5-18 (U) or J1-5 (SU) - Body ground Always 10 kΩ or higher
G5-10 (D) or J1-2 (SD) - Body ground Always 10 kΩ or higher




Result:
Proceed to
OK
NG



OK

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR