The air mix damper servo sub-assembly sends pulse signals to indicate the damper position to the air conditioning amplifier assembly. The air conditioning amplifier assembly activates the motor (normal or reverse) based on these signals to move the air mix damper servo sub-assembly to the appropriate position. This adjusts the amount of air passing through the heater core after passing the evaporator and controls the temperature of the output air. The air conditioning amplifier assembly communicates with the servo through a communication/driver IC and wiring assembly called the air conditioning harness assembly.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Memory |
|---|---|---|---|---|
| B1441 | Air Mix Damper Control Servo Motor Circuit (Passenger Side) | Air mix damper position sensor value does not change even if air conditioning amplifier assembly operates air mix damper servo sub-assembly | ·
Air mix damper servo sub-assembly ·
Air conditioning harness assembly ·
Air conditioning amplifier assembly |
Memorized
(30 seconds or more)*1 |
*1: The air conditioning amplifier assembly stores this DTC if the malfunction has occurred for the period of time indicated in the brackets.
Confirm that no mechanical problem is present because this DTC can be output when either a damper link or damper is mechanically locked.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Operate the set temperature switch.
Enter the following menus: Body Electrical / Air Conditioner / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Air Mix Servo Targ Pulse(D) | Air mix damper servo sub-assembly target pulse | Min.: 128
Max.: 383 |
MAX COLD: 257 (pulse)
MAX HOT: 183 (pulse) |
- |
| Air Mix Servo Actual Pulse(D) | Air mix damper servo sub-assembly actual pulse | Min.: 128
Max.: 383 |
MAX COLD: 257 (pulse)
MAX HOT: 183 (pulse) |
- |
| Tester Display |
|---|
| Air Mix Servo Targ Pulse(D) |
| Tester Display |
|---|
| Air Mix Servo Actual Pulse(D) |
The display is as specified in the normal condition column.
| Result | Proceed to |
|---|---|
| NG | A |
| OK (When troubleshooting according to Problem Symptoms Table) | B |
| OK (When troubleshooting according to the DTC) | C |
A
B
C
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Air Conditioner / Active Test.
According to the display on the GTS, perform the Active Test.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Air Mix Servo Targ Pulse(D) | Air mix damper servo sub-assembly pulse | Min.: 128
Max.: 383 |
Operates between 183 and 257 pulses |
| Tester Display |
|---|
| Air Mix Servo Targ Pulse(D) |
Recirculation damper servo sub-assembly operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the air mix damper servo sub-assembly.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING UNIT>DISASSEMBLY
Since the air mix damper servo sub-assembly cannot be inspected while it is removed from the vehicle, replace the air mix damper servo sub-assembly with a new or known good one and check that the condition returns to normal.
Check for the DTC.
If the battery is disconnected, the past DTCs will be cleared.
| Result | Proceed to |
|---|---|
| DTC B1441 is output | A |
| DTC B1441 is not output | B |
A
B
Replace the air conditioning harness assembly.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING UNIT>DISASSEMBLY
Since the air conditioning harness assembly cannot be inspected while it is removed from the vehicle, replace the air conditioning harness assembly with a new or known good one and check that the condition returns to normal.
Check for the DTC.
If the battery is disconnected, the past DTCs will be cleared.
| Result | Proceed to |
|---|---|
| DTC B1441 is output | A |
| DTC B1441 is not output | B |
A
B