The recirculation damper servo sub-assembly sends pulse signals to inform the air conditioning amplifier assembly of the damper position. The air conditioning amplifier assembly activates the motor (normal, reverse) based on the signals to move the air inlet mode selection recirculation damper servo sub-assembly to any position, which controls the air inlet mode (fresh, fresh/recirculation, and recirculation).
The air conditioning amplifier assembly communicates with the servo through a communication/driver IC and wiring assembly called the air conditioning harness assembly.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Memory |
|---|---|---|---|---|
| B1442 | Air Inlet Damper Control Servo Motor Circuit | Air inlet damper position sensor value does not change even if air conditioning amplifier assembly operates recirculation damper servo sub-assembly | ·
Recirculation damper servo sub-assembly ·
Air conditioning harness assembly ·
Air conditioning amplifier assembly |
Memorized
(30 seconds or more)*1 |
*1: The air conditioning amplifier assembly stores this DTC if the malfunction has occurred for the period of time indicated in the brackets.
Confirm that no mechanical problem is present because this DTC can be output when either a damper link or damper is mechanically locked.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Operate the recirculation/fresh switch.
Enter the following menus: Body Electrical / Air Conditioner / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Air Inlet Damper Targ Pulse | Recirculation damper servo sub-assembly target pulse | Min.: 128
Max.: 383 |
RECIRCULATION: 255 (pulse)
FRESH: 270 (pulse) |
- |
| Air Inlet Damper Actual Pulse | Recirculation damper servo sub-assembly actual pulse | Min.: 128
Max.: 383 |
RECIRCULATION: 255 (pulse)
FRESH: 270 (pulse) |
- |
| Tester Display |
|---|
| Air Inlet Damper Targ Pulse |
| Tester Display |
|---|
| Air Inlet Damper Actual Pulse |
The display is as specified in the normal condition column.
| Result | Proceed to |
|---|---|
| NG | A |
| OK (When troubleshooting according to Problem Symptoms Table) | B |
| OK (When troubleshooting according to the DTC) | C |
A
B
C
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Air Conditioner / Active Test.
According to the display on the GTS, perform the Active Test.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Air Inlet Damper Targ Pulse | Recirculation damper servo sub-assembly pulse | Min.: 128
Max.: 383 |
Operates between 255 and 270 pulses |
| Tester Display |
|---|
| Air Inlet Damper Targ Pulse |
Recirculation damper servo sub-assembly operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the recirculation damper servo sub-assembly.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING UNIT>DISASSEMBLY
Since the recirculation damper servo sub-assembly cannot be inspected while it is removed from the vehicle, replace the recirculation damper servo sub-assembly with a new or known good one and check that the condition returns to normal.
Check for the DTC.
If the battery is disconnected, the past DTCs will be cleared.
| Result | Proceed to |
|---|---|
| DTC B1442 is output | A |
| DTC B1442 is not output | B |
A
B
Replace the air conditioning harness assembly.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING UNIT>DISASSEMBLY
Since the air conditioning harness assembly cannot be inspected while it is removed from the vehicle, replace the air conditioning harness assembly with a new or known good one and check that the condition returns to normal.
Check for the DTC.
If the battery is disconnected, the past DTCs will be cleared.
| Result | Proceed to |
|---|---|
| DTC B1442 is output | A |
| DTC B1442 is not output | B |
A
B