Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)
RM30M0E _58 Vehicle Interior _017118 HEATING / AIR CONDITIONING _0086573 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) J

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  Back-up Power Source Circuit  


DESCRIPTION

The back-up power source circuit for the air conditioning amplifier assembly is shown below. Power is supplied even when the ignition switch is off. This power is used for diagnostic trouble code memory, etc.

WIRING DIAGRAM

E272058E02
4.74,0.729 5.052,0.927 0.313,0.198 10 false B 4.438,0.615 4.75,0.813 0.313,0.198 10 false 21 4.438,1.302 4.75,1.5 0.313,0.198 10 false 14 4.729,1.417 5.146,1.604 0.417,0.188 10 false GND 4.448,1.948 4.76,2.146 0.313,0.198 10 false F3 4.438,2.094 6.667,2.344 2.229,0.25 10 false Air Conditioning Amplifier Assembly 2.708,0.906 3.177,1.104 0.469,0.198 10 false DOME 0.688,0.719 1.51,0.969 0.823,0.25 10 false from Battery

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - POWER SOURCE)
a.

Disconnect the air conditioning amplifier assembly connector.


b.
E281476C04
1.479,0.115 1.927,0.323 0.448,0.208 0.354,1.375 0.24,1.688 true 1.615,0.115 1.927,0.313 0.313,0.198 10 false F3 0.198,1.698 0.51,1.896 0.313,0.198 10 false B 0.125,0.094 0.438,0.292 0.313,0.198 10 false *a
*a Front view of wire harness connector (to Air Conditioning Amplifier Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F3-21 (B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - BODY GROUND)
a.
E281476C05
1.479,0.115 1.927,0.323 0.448,0.208 2.177,1.188 2.021,1.698 true 1.615,0.115 1.927,0.313 0.313,0.198 10 false F3 1.865,1.698 2.177,1.906 0.313,0.208 10 false GND 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a
*a Front view of wire harness connector (to Air Conditioning Amplifier Assembly)


Disconnect the air conditioning amplifier assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F3-14 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR