84870A
1.INSPECT OUTER MIRROR SWITCH ASSEMBLY (w/ Power Retract Mirror)
| *a | Component without harness connected
(Outer Mirror Switch Assembly) |
| *b | Left/Right Select Switch |
| *c | Mirror Adjust Switch |
Check the mirror adjust switch.
Select "L" on the left/right select switch.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition | |
|---|---|---|---|
| 4 (VL) - 8 (B)
6 (M+) - 7 (E) |
UP | Pushed | Below 1 Ω |
| Not Pushed | 10 kΩ or higher | ||
| 4 (VL) - 7 (E)
6 (M+) - 8 (B) |
DOWN | Pushed | Below 1 Ω |
| Not Pushed | 10 kΩ or higher | ||
| 5 (HL) - 8 (B)
6 (M+) - 7 (E) |
LEFT | Pushed | Below 1 Ω |
| Not Pushed | 10 kΩ or higher | ||
| 5 (HL) - 7 (E)
6 (M+) - 8 (B) |
RIGHT | Pushed | Below 1 Ω |
| Not Pushed | 10 kΩ or higher | ||
Select "R" on the left/right select switch.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition | |
|---|---|---|---|
| 3 (VR) - 8 (B)
6 (M+) - 7 (E) |
UP | Pushed | Below 1 Ω |
| Not Pushed | 10 kΩ or higher | ||
| 3 (VR) - 7 (E)
6 (M+) - 8 (B) |
DOWN | Pushed | Below 1 Ω |
| Not Pushed | 10 kΩ or higher | ||
| 2 (HR) - 8 (B)
6 (M+) - 7 (E) |
LEFT | Pushed | Below 1 Ω |
| Not Pushed | 10 kΩ or higher | ||
| 2 (HR) - 7 (E)
6 (M+) - 8 (B) |
RIGHT | Pushed | Below 1 Ω |
| Not Pushed | 10 kΩ or higher | ||
If the result is not as specified, replace the outer mirror switch assembly.
| *a | Component without harness connected
(Outer Mirror Switch Assembly) |
| *b | Fold Away Switch |
Check the fold away switch.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 10 (MF) - 7 (E)
9 (MR) - 8 (B) |
Pushed | Below 1 Ω |
| 10 (MF) - 8 (B)
9 (MR) - 7 (E) |
Not Pushed | Below 1 Ω |
If the result is not as specified, replace the outer mirror switch assembly.
84870A
2.INSPECT OUTER MIRROR SWITCH ASSEMBLY (w/o Power Retract Mirror)
| *a | Component without harness connected
(Outer Mirror Switch Assembly) |
| *b | Left/Right Select Switch |
| *c | Mirror Adjust Switch |
Check the mirror adjust switch.
Select "L" on the left/right select switch.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition | |
|---|---|---|---|
| 4 (VL) - 8 (B)
6 (M+) - 7 (E) |
UP | Pushed | Below 1 Ω |
| Not Pushed | 10 kΩ or higher | ||
| 4 (VL) - 7 (E)
6 (M+) - 8 (B) |
DOWN | Pushed | Below 1 Ω |
| Not Pushed | 10 kΩ or higher | ||
| 5 (HL) - 8 (B)
6 (M+) - 7 (E) |
LEFT | Pushed | Below 1 Ω |
| Not Pushed | 10 kΩ or higher | ||
| 5 (HL) - 7 (E)
6 (M+) - 8 (B) |
RIGHT | Pushed | Below 1 Ω |
| Not Pushed | 10 kΩ or higher | ||
Select "R" on the left/right select switch.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition | |
|---|---|---|---|
| 3 (VR) - 8 (B)
6 (M+) - 7 (E) |
UP | Pushed | Below 1 Ω |
| Not Pushed | 10 kΩ or higher | ||
| 3 (VR) - 7 (E)
6 (M+) - 8 (B) |
DOWN | Pushed | Below 1 Ω |
| Not Pushed | 10 kΩ or higher | ||
| 2 (HR) - 8 (B)
6 (M+) - 7 (E) |
LEFT | Pushed | Below 1 Ω |
| Not Pushed | 10 kΩ or higher | ||
| 2 (HR) - 7 (E)
6 (M+) - 8 (B) |
RIGHT | Pushed | Below 1 Ω |
| Not Pushed | 10 kΩ or higher | ||
If the result is not as specified, replace the outer mirror switch assembly.