Home › Vehicle Exterior › DOOR / HATCH › REAR DOOR › 2013.08–2014.03
RM30M0E _59 Vehicle Exterior _017122 DOOR / HATCH _0087457 REAR DOOR N

DOOR / HATCH  REAR DOOR  ADJUSTMENT  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the LH side and RH side.

·

The procedure listed below is for the LH side.

·
B280381C12
0.729,0.115 1.042,0.313 0.313,0.198 10 false *a 2.531,0.115 2.844,0.313 0.313,0.198 10 false *b
*a Centering Bolt
*b Standard Bolt


Centering bolts are used to mount the door hinge to the vehicle body and the door. The door cannot be adjusted with the centering bolts installed. Substitute the centering bolts with standard bolts when making adjustments.

·

Specified torque for standard bolts is shown in the standard bolt chart.

Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS



PROCEDURE

Hide 67004 1.INSPECT REAR DOOR PANEL SUB-ASSEMBLY

a.

Check that the clearance measurements are within the standard ranges.

B346772C01
2.458,0.531 2.615,0.729 0.156,0.198 10 false A 2.438,1.094 2.594,1.292 0.156,0.198 10 false B 3.917,0.427 4.073,0.625 0.156,0.198 10 false C 3.865,0.948 4.021,1.146 0.156,0.198 10 false D 6.813,3.302 6.969,3.5 0.156,0.198 10 false F 6.448,3.531 6.604,3.729 0.156,0.198 10 false E 4.844,5.104 5,5.302 0.156,0.198 10 false H 4.417,5.344 4.573,5.542 0.156,0.198 10 false G 3.24,5.042 3.396,5.24 0.156,0.198 10 false I 0.677,4.167 0.833,4.365 0.156,0.198 10 false J 1.156,3.896 1.313,4.094 0.156,0.198 10 false K 0.688,2.583 0.844,2.781 0.156,0.198 10 false L

Standard Clearance:
Area Measurement Area Measurement
A 4.0 to 7.0 mm (0.157 to 0.276 in.) B 6.3 to 9.3 mm (0.248 to 0.366 in.)
C 4.9 to 7.9 mm (0.193 to 0.311 in.) D 5.3 to 8.3 mm (0.209 to 0.327 in.)
E 2.9 to 5.9 mm (0.114 to 0.232 in.) F -1.5 to 1.5 mm (-0.0591 to 0.0591 in.)
G 2.9 to 5.9 mm (0.114 to 0.232 in.) H -1.5 to 1.5 mm (-0.0591 to 0.0591 in.)
I 4.5 to 7.5 mm (0.177 to 0.295 in.) J 3.2 to 5.6 mm (0.126 to 0.220 in.)
K -1.2 to 1.2 mm (-0.0472 to 0.0472 in.) L 4.4 mm (0.173 in.)



Hide 67004 2.ADJUST REAR DOOR PANEL SUB-ASSEMBLY

HINT:

Use the same procedure for both sides.


a.
B346773

Using SST, adjust the door horizontally and vertically by loosening the 4 body side hinge bolts.

SST
09812-00010  


b.

Tighten the 4 body side hinge bolts after the adjustment.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


c.
B346774

Using SST, adjust the door horizontally and vertically by loosening the 4 door side hinge bolts.

SST
09812-00010  


d.

Tighten the 4 door side hinge bolts after the adjustment.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


e.
B346775

Using a T40 "TORX" socket wrench, slightly loosen the 2 striker mounting screws.


f.

Using a plastic-faced hammer, hit the striker to adjust its position.


g.

Using a T40 "TORX" socket wrench, tighten the striker mounting 2 screws after the adjustment.

Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)