Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2013.08–2014.03
RM30M0E _58 Vehicle Interior _017113 METER / GAUGE / DISPLAY _0087658 METER / GAUGE SYSTEM C

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  B1507  Open in Turn Signal Circuit  B1508  Short in Turn Signal / Hazard Flasher Circuit  


DESCRIPTION

These DTCs are stored when the combination meter assembly detects an open in a turn signal light circuit, a short in a turn signal light circuit, or a short in the hazard warning light circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory Note
B1507 Open in Turn Signal Circuit When IG voltage is 9.5 V or more and the following condition is detected:
·

Open in turn signal light circuit


·

Bulb

·

Harness or connector

·

No. 6 junction connector

·

Combination meter assembly


DTC stored -
B1508 Short in Turn Signal / Hazard Flasher Circuit When IG voltage is 9.5 V or more and the following condition is detected:
·

Short in turn signal light circuit or hazard warning light circuit


·

Bulb

·

Harness or connector

·

No. 6 junction connector

·

Combination meter assembly


DTC stored -

WIRING DIAGRAM

E279542
1.583,0.125 1.74,0.323 0.156,0.198 10 false 1 2.802,0.125 2.958,0.323 0.156,0.198 10 false 2 2.094,0.417 2.708,0.615 0.615,0.198 10 false Turn 2.115,1.635 2.729,1.833 0.615,0.198 10 false Turn 2.115,2.854 2.729,3.052 0.615,0.198 10 false Turn 1.76,0.125 1.917,0.323 0.156,0.198 10 false E 2.646,0.125 2.802,0.323 0.156,0.198 10 false B 4.229,0.188 4.688,0.385 0.458,0.198 10 false F68 4.26,0.031 4.573,0.229 0.313,0.198 10 false 16 4.26,1.26 4.573,1.458 0.313,0.198 10 false 17 5.917,0.104 6.229,0.302 0.313,0.198 10 false 13 6.125,0.188 6.438,0.385 0.313,0.198 10 false LL 1.5,0.76 1.958,0.958 0.458,0.198 10 false A12 1.5,0.896 3,1.333 1.5,0.438 10 false Headlight Assembly LH 5.094,0.188 5.552,0.385 0.458,0.198 10 false F68 5.146,0.031 5.458,0.229 0.313,0.198 10 false 17 4.229,1.406 4.688,1.604 0.458,0.198 10 false F69 4.26,2.49 4.573,2.688 0.313,0.198 10 false 18 4.229,2.646 4.688,2.844 0.458,0.198 10 false F68 2.646,1.344 2.802,1.542 0.156,0.198 10 false B 1.76,1.354 1.917,1.552 0.156,0.198 10 false E 1.552,1.354 1.719,1.563 0.167,0.208 10 false 4 2.802,1.333 3.052,1.688 0.25,0.354 10 false 5 1.083,2.167 6.281,2.365 5.198,0.198 10 false Rear Combination Light Assembly LH 1.083,2.01 2.917,2.208 1.833,0.198 10 false F25 1.583,2.583 1.74,2.781 0.156,0.198 10 false 6 1.76,2.583 1.917,2.781 0.156,0.198 10 false E 2.635,2.583 2.792,2.781 0.156,0.198 10 false B 2.802,2.583 3.167,2.75 0.365,0.167 10 false 10 1.104,3.25 1.917,3.417 0.813,0.167 10 false H6 1.083,3.417 6.583,3.615 5.5,0.198 10 false Outer Rear View Mirror Assembly LH*1 2.385,3.74 2.542,3.938 0.156,0.198 10 false 1 2.01,3.74 2.167,3.938 0.156,0.198 10 false 2 1.083,4 2.688,4.26 1.604,0.26 10 false A15 1.083,4.135 6.583,4.333 5.5,0.198 10 false Side Turn Signal Light Assembly LH*2 2.115,4.906 2.729,5.104 0.615,0.198 10 false Turn 2.635,4.635 2.792,4.833 0.156,0.198 10 false B 1.75,4.635 1.906,4.833 0.156,0.198 10 false E 2.802,4.635 2.958,4.833 0.156,0.198 10 false 2 1.583,4.625 1.74,4.823 0.156,0.198 10 false 1 1.5,5.302 2.313,5.469 0.813,0.167 10 false A11 1.5,5.427 4.708,5.625 3.208,0.198 10 false Headlight Assembly RH 4.229,4.698 4.688,4.896 0.458,0.198 10 false F68 4.302,4.521 4.615,4.719 0.313,0.198 10 false 1 5.083,4.698 5.542,4.896 0.458,0.198 10 false F68 5.188,4.531 5.5,4.729 0.313,0.198 10 false 2 1.594,5.896 1.823,6.125 0.229,0.229 10 false 4 2.802,5.896 3.063,6.25 0.26,0.354 10 false 5 2.115,6.177 2.729,6.375 0.615,0.198 10 false Turn 1.083,6.583 2.917,6.781 1.833,0.198 10 false F26 1.083,6.75 6.281,6.948 5.198,0.198 10 false Rear Combination Light Assembly RH 4.229,5.979 4.688,6.177 0.458,0.198 10 false F69 4.271,5.792 4.583,5.99 0.313,0.198 10 false 10 1.75,5.917 1.906,6.115 0.156,0.198 10 false E 2.635,5.917 2.792,6.115 0.156,0.198 10 false B 2.635,7.219 2.792,7.417 0.156,0.198 10 false B 1.75,7.208 1.906,7.406 0.156,0.198 10 false E 2.802,7.208 3.167,7.375 0.365,0.167 10 false 10 1.583,7.198 1.74,7.396 0.156,0.198 10 false 6 2.115,7.479 2.729,7.677 0.615,0.198 10 false Turn 1.083,7.875 1.896,8.042 0.813,0.167 10 false G6 1.083,8 6.583,8.198 5.5,0.198 10 false Outer Rear View Mirror Assembly RH*1 2.01,8.25 2.167,8.448 0.156,0.198 10 false 2 2.375,8.25 2.531,8.448 0.156,0.198 10 false 1 4.229,7.271 4.688,7.469 0.458,0.198 10 false F69 4.271,7.094 4.583,7.292 0.313,0.198 10 false 11 1.083,8.51 2.969,8.75 1.885,0.24 10 false A16 1.083,8.667 3.5,8.917 2.417,0.25 10 false Side Turn Signal Light Assembly RH*2 0.333,9.49 3.25,9.875 2.917,0.385 10 false *2: for Front Fender Type Side Turn Signal Light 0.333,9.115 3.917,9.5 3.583,0.385 10 false *1: for Outer Rear View Mirror Type Side Turn Signal Light 4.083,7.875 7.156,8.125 3.073,0.25 10 false No. 6 Junction Connector 5.917,7.885 6.375,8.083 0.458,0.198 10 false F39 5.917,8.031 7.156,8.521 1.24,0.49 10 false Combination Meter Assembly 5.969,4.615 6.281,4.813 0.313,0.198 10 false 7 6.115,4.719 6.427,4.917 0.313,0.198 10 false LR

CAUTION / NOTICE / HINT

NOTICE:

Inspect the bulbs for this system before performing the following procedure.


PROCEDURE

1.INSPECT LIGHTS
a.

Inspect the illumination of each turn signal light.


Result:
Result Proceed to
Turn signal lights for one side do not illuminate. A
Front turn signal light does not illuminate. B
Rear turn signal light does not illuminate. C
Side turn signal light does not illuminate (for Outer Rear View Mirror Type Side Turn Signal Light). D
Side turn signal light does not illuminate (for Front Fender Type Side Turn Signal Light). E



A

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 6 JUNCTION CONNECTOR)

B

3.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY - NO. 6 JUNCTION CONNECTOR)

C

4.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT ASSEMBLY - NO. 6 JUNCTION CONNECTOR)

D

5.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY - NO. 6 JUNCTION CONNECTOR)

E

6.CHECK HARNESS AND CONNECTOR (SIDE TURN SIGNAL LIGHT ASSEMBLY - NO. 6 JUNCTION CONNECTOR)
2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 6 JUNCTION CONNECTOR)
a.

Disconnect the F39 combination meter assembly connector.


b.

Disconnect the F68 No. 6 junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
for LH
Tester Connection Condition Specified Condition
F39-13 (LL) - F68-17 Always Below 1 Ω

for RH
Tester Connection Condition Specified Condition
F39-7 (LR) - F68-2 Always Below 1 Ω


Standard Resistance (Check for Short):
for LH
Tester Connection Condition Specified Condition
F39-13 (LL) or F68-17 - Body ground Always 10 kΩ or higher

for RH
Tester Connection Condition Specified Condition
F39-7 (LR) or F68-2 - Body ground Always 10 kΩ or higher



Result:
Result Proceed to
NG A
OK B



A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

7.INSPECT NO. 6 JUNCTION CONNECTOR
3.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY - NO. 6 JUNCTION CONNECTOR)
a.

Disconnect the A12*1 or A11*2 headlight assembly connector.

*1: for LH

*2: for RH



b.

Disconnect the F68 No. 6 junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
for LH
Tester Connection Condition Specified Condition
A12-2 (B) - F68-16 Always Below 1 Ω
A12-1 (E) - Body ground Always Below 1 Ω

for RH
Tester Connection Condition Specified Condition
A11-2 (B) - F68-1 Always Below 1 Ω
A11-1 (E) - Body ground Always Below 1 Ω


Standard Resistance (Check for Short):
for LH
Tester Connection Condition Specified Condition
A12-2 (B) or F68-16 - Body ground Always 10 kΩ or higher

for RH
Tester Connection Condition Specified Condition
A11-2 (B) or F68-1 - Body ground Always 10 kΩ or higher



Result:
Result Proceed to
NG A
OK B



A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

7.INSPECT NO. 6 JUNCTION CONNECTOR
4.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT ASSEMBLY - NO. 6 JUNCTION CONNECTOR)
a.

Disconnect the F25*1 or F26*2 rear combination light assembly connector.

*1: for LH

*2: for RH



b.

Disconnect the F69 No. 6 junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
for LH
Tester Connection Condition Specified Condition
F25-5 (B) - F69-17 Always Below 1 Ω
F25-4 (E) - Body ground Always Below 1 Ω

for RH
Tester Connection Condition Specified Condition
F26-5 (B) - F69-10 Always Below 1 Ω
F26-4 (E) - Body ground Always Below 1 Ω


Standard Resistance (Check for Short):
for LH
Tester Connection Condition Specified Condition
F25-5 (B) or F69-17 - Body ground Always 10 kΩ or higher

for RH
Tester Connection Condition Specified Condition
F26-5 (B) or F69-10 - Body ground Always 10 kΩ or higher



Result:
Result Proceed to
NG A
OK B



A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

7.INSPECT NO. 6 JUNCTION CONNECTOR
5.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY - NO. 6 JUNCTION CONNECTOR)
a.

Disconnect the H6*1 or G6*2 outer rear view mirror assembly connector.

*1: for LH

*2: for RH



b.

Disconnect the F68*1 or F69*2 No. 6 junction connector.

*1: for LH

*2: for RH



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
for LH
Tester Connection Condition Specified Condition
H6-10 (B) - F68-18 Always Below 1 Ω
H6-6 (E) - Body ground Always Below 1 Ω

for RH
Tester Connection Condition Specified Condition
G6-10 (B) - F69-11 Always Below 1 Ω
G6-8 (E) - Body ground Always Below 1 Ω


Standard Resistance (Check for Short):
for LH
Tester Connection Condition Specified Condition
H6-10 (B) or F68-18 - Body ground Always 10 kΩ or higher

for RH
Tester Connection Condition Specified Condition
G6-10 (B) or F69-11 - Body ground Always 10 kΩ or higher



Result:
Result Proceed to
NG A
OK B



A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

7.INSPECT NO. 6 JUNCTION CONNECTOR
6.CHECK HARNESS AND CONNECTOR (SIDE TURN SIGNAL LIGHT ASSEMBLY - NO. 6 JUNCTION CONNECTOR)
a.

Disconnect the A15*1 or A16*2 side turn signal light assembly connector.

*1: for LH

*2: for RH



b.

Disconnect the F68*1 or F69*2 No. 6 junction connector.

*1: for LH

*2: for RH



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
for LH
Tester Connection Condition Specified Condition
A15-1 - F68-18 Always Below 1 Ω
A15-2 - Body ground Always Below 1 Ω

for RH
Tester Connection Condition Specified Condition
A16-1 - F69-11 Always Below 1 Ω
A16-2 - Body ground Always Below 1 Ω


Standard Resistance (Check for Short):
for LH
Tester Connection Condition Specified Condition
A15-1 or F68-18 - Body ground Always 10 kΩ or higher

for RH
Tester Connection Condition Specified Condition
A16-1 or F69-11 - Body ground Always 10 kΩ or higher



Result:
Result Proceed to
NG A
OK B



A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

7.INSPECT NO. 6 JUNCTION CONNECTOR
7.INSPECT NO. 6 JUNCTION CONNECTOR
a.
E270875C05
0.125,1.063 0.5,1.229 0.375,0.167 0.125,1.313 0.5,1.479 0.375,0.167 0,0 0.313,0.156 0.313,0.156 10 false *a 0.198,1.063 0.583,1.229 0.385,0.167 10 false F68 0.208,1.313 0.604,1.479 0.396,0.167 10 false F69
*a Component without harness connected
(No. 6 Junction Connector)


Remove the No. 6 junction connector.


b.

Front turn signal light

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LH
Tester Connection Condition Specified Condition
F68-17 - F68-16 Always Below 1 Ω


for RH
Tester Connection Condition Specified Condition
F68-2 - F68-1 Always Below 1 Ω



c.

Rear turn signal light

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LH
Tester Connection Condition Specified Condition
F68-17 - F69-17 Always Below 1 Ω


for RH
Tester Connection Condition Specified Condition
F68-2 - F69-10 Always Below 1 Ω



d.

Side turn signal light

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LH
Tester Connection Condition Specified Condition
F68-17 - F68-18 Always Below 1 Ω


for RH
Tester Connection Condition Specified Condition
F68-2 - F69-11 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE NO. 6 JUNCTION CONNECTOR